HT-E8200_XU_0315.indd 16 HT-E8200_XU_0315.indd 16 2012-03-15 오후 1:10:32 2012-03-15 오후 1:10:32English 17 | 03 Connections Installing the Wall Mount You can use the wall mount bracket to mount this unit on a wall. Installation Precautions • Do not install on a place other than a vertical wall. • For the installation, avoid a location with high temperature or humidity. • Check the strength of the wall. If the strength of the wall is insufficient for the product installation, make sure to reinforce the wall before the installation. • Check the material of the wall. If the wall is made of plaster board, marble, or iron board, purchase and use the appropriate fixing screws. • Cables connecting to external devices need to be connected to the set before installing. • Be sure to turn off and unplug the unit before installation. Otherwise, it may cause electric shock. 1 . Rotate a screw on the cradle stand counterclockwise to seperate them from the unit. 2 . Place the wall mount bracket on a wall surface and then secure it with two screws (not supplied). Be sure to install the wall mount bracket so that the arrow (  ) is placed in the centre of the TV. 3 . Then, fit the unit into the corresponding slots of the wall mount bracket. For secure installation, make sure the mounting studs slide firmly down into the bottom of the slots. 4 . This is the completion of the suggested wall mount installation. | NOTE |  Do not hang onto the installed unit and avoid any impact to the unit.  When the unit is installed on a wall, please make sure that a child does not pull any of connecting cables, as it may cause it to fall.  When you install the product with TV on the wall, leave sufficient space for ejecting a CD. (Disc size 12cm+ space for moving hands) HDMI OUT HDMI IN 1 HDMI IN 2 LAN VIDEO OUT OPTICAL IN FM ANT 1 2 1 2 3 4 HT-E8200_XU_0315.indd 17 HT-E8200_XU_0315.indd 17 2012-03-15 오후 1:10:35 2012-03-15 오후 1:10:35| 18 English Connections Connecting to a TV Select either Method 1 or Method 2. • If you have set the product's remote control to operate your TV, press the TV SOURCE button on the remote control, and then select the correct external source from the TV's source list (HDMI, Video In, etc.) to view video from the home Cinema. VIDEO IN HDMI IN HDMI OUT HDMI IN 1 HDMI IN 2 LAN VIDEO OUT OPTICAL IN FM ANT Method 2 (Cable not supplied.) Method 1 Method 1 Connecting to a TV with a Video Cable - Good Quality Connect the supplied Video cable from the VIDEO OUT jack on the back of the product to the VIDEO IN jack on your TV. Method 2 Connecting to a TV with an HDMI Cable - Best Quality (Recommended) Connect an HDMI cable (not supplied) from the HDMI OUT jack on the back of the product to the HDMI IN jack on your TV. If the TV supports ARC, you can hear TV sound from home cinema with only connect this cable. | NOTE |  The VIDEO Out jack always outputs in the 576i/480i resolution regardless of the resolution set in the Setup menu.  Do not connect the unit through a VCR. Video signals fed through VCRs may be affected by copyright protection systems and the picture will be distorted on the television. HT-E8200_XU_0315.indd 18 HT-E8200_XU_0315.indd 18 2012-03-15 오후 1:10:38 2012-03-15 오후 1:10:38English 19 | 03 Connections Connecting to External Devices To select the correct mode for an external device, press the FUNCTION button. Each time you press the button, the mode changes in this order : BD/DVD  D. IN  AUX  HDMI1  HDMI2  FM BT HDMI OUT HDMI IN 1 HDMI IN 2 LAN VIDEO OUT OPTICAL IN FM ANT AUDIO OUT OPTICAL OUT HDMI OUT AUX IN External Devices Method 2 (Cable not supplied.) (Cable not supplied.) Method 3 (Cable not supplied.) Audio Cable (not supplied) If the external analogue component has only one Audio Out, connect either left or right. Method 1 Method 1 AUX IN : Connecting an External Analogue Component Using an RCA audio cable (not supplied), connect the AUDIO In jack on the product to the AUDIO Out jack on the external analogue component.  Select the AUX mode. • Be sure to match the colours on the cable plugs to the colours on the input and output jacks. Method 2 OPTICAL IN : Connecting an External Digital Audio Component To connect the digital audio output of digital signal components such as Cable Boxes and Satellite Receivers (Set-Top-Boxes). Using a digital optical cable (not supplied), connect the Optical Digital Audio In jack on the product to the Digital Optical Out jack of the external digital device using a digital optical cable.  Select the D. IN mode. Method 3 HDMI IN : Connecting to an External Component with an HDMI Cable Connect an HDMI cable (not supplied) from the HDMI IN jack on the back of the product to the HDMI OUT jack on your digital device.  Select the HDMI1 or HDMI2 mode. | NOTE |  To see video from your Cable Box/Satellite receiver, you must connect its video output directly to your TV.  This system supports Digital sampling frequencies of 32 kHz or higher from external digital components.  This system supports only DTS and Dolby Digital audio. MPEG audio, a bitstream format, is not supported. HT-E8200_XU_0315.indd 19 HT-E8200_XU_0315.indd 19 2012-03-15 오후 1:10:40 2012-03-15 오후 1:10:40| 20 English Connections Connecting to a Network Router You can connect your product to your network router using one of the methods illustrated below. Wired Network HDMI OUT HDMI IN 1 HDMI IN 2 LAN VIDEO OUT OPTICAL IN FM ANT Broadband service Broadband service Broadband modem (with integrated router) Broadband modem Router Or | NOTE |  Internet access to Samsung’s Software Update server may not be allowed, depending on the router you use or your ISP’s policy. For more information, contact your ISP (Internet Service Provider).  DSL users, please use a router to make a network connection.  To use the AllShare Play function, you must connect your PC to your network as shown in the illustrations on the left. The connection can be wired or wireless. Wireless Network Wireless IP sharer Broadband service | NOTE |  If your wireless IP router supports DHCP, this product can use a DHCP or static IP address to connect to the wireless network.  Set your wireless IP router to Infrastructure mode. Ad-hoc mode is not supported.  The product supports only the following wireless security key protocols: - WEP (OPEN/SHARED), WPA-PSK (TKIP/AES), WPA2-PSK (TKIP/AES)  Select a channel on the wireless IP router that is not currently being used. If the channel set for the wireless IP router is currently being used by another device nearby, it will result in interference and communication failure.  If you select the Pure High-throughput (Greenfield) 802.11n mode and set the Encryption type on your router or AP to WEP, TKIP or TKIP-AES (WPS2Mixed), the product will not support a connection in compliance with new WiFi certification specifications.  Wireless LAN, by its nature, may cause interference, depending on the operating conditions (AP performance, distance, obstacles, interference by other radio devices, etc). HT-E8200_XU_0315.indd 20 HT-E8200_XU_0315.indd 20 2012-03-15 오후 1:10:42 2012-03-15 오후 1:10:42English 21 | 04 Settings The Initial Settings Procedure • The Home menu will not appear if you do not configure the initial settings. • The OSD (On Screen Display) may change in this product after you upgrade the software version. • The access steps may differ depending on the menu you selected. 1 . Turn on your TV after connecting the product, and then turn on the product. When you turn on the product for the first time, the product automatically displays the Initial Settings Language screen. 2 . Use the ▲▼◄► buttons on the remote to select the desired language, and then press the E button twice. The Start screen appears. 3 . Press the E button to start setup. The Network Settings screen appears. The next step is to set up a wireless network using an internal LAN Adapter. If you want to connect to your wired network, plug in a network cable. Previous Skip Next Initial Settings > Network Settings (1/5) 4 . Press the E button to set up the product’s wireless network connection or select Skip, and then press the E button to skip network setup. If you selected Skip, go to Step 12. | NOTE |  The product starts the wireless network connection procedure by default. If you want to set up a wired connection, select Skip, and then go to "Configuring Your Network Connection" on page 29 after you have completed the Initial Settings Procedure.  If you skip wireless network setup here, go to "Wireless Network" on page 30 to set up the product's wireless network connection later. 5 . The product searches for and then displays all available wireless router network connections. Initial Settings > Network Settings (2/5) Refresh WPS(PBC) Previous Next Skip Select your wireless router from the list. 1 / 4 KIMING_VTOWER TIAS si-ap Add Network surlwang5 6 . Use the ▲▼ buttons to select a router, and then press the E button. The Next button is highlighted. 7 . Press the E button to continue. The Security Key screen appears. | NOTE |  If you have a WPS(PBC) compatible router, select WPS(PBC) instead, press the E button, and then follow the directions on the screen. When done, go to Step 10. Initial Settings > Network Settings (4/5) Previous WPS PIN Skip Next Enter security key. 0 entered A/a  Space    a g m s e k q w c i o u 1 4 7 y b h n t f l r x d j p v 2 5 8 z 3 6 9 0 - 8 . Enter your network's security key. When done, use the ▲▼◄► buttons to select Next, and then press the E button. Settings HT-E8200_XU_0315.indd 21 HT-E8200_XU_0315.indd 21 2012-03-15 오후 1:10:45 2012-03-15 오후 1:10:45| 22 English Settings | NOTE |  Enter numbers by pressing the number buttons on your remote.  Enter letters by selecting a letter using the ▲▼◄► buttons, and then press E button.  To display capital letters (or redisplay small letters if capital letters are displayed), select A/a, and then press the E button.  To display symbols and punctuation, select , and then press the E button. To redisplay letters, select , and then press the E button. 9 . If the connection is successful, the Connection Complete screen appears. Select Next, and then press the E button. The Software Update screen appears. | NOTE |  If the connection is not successful, select Next, and then press the E button. After you have completed the Initial Settings procedure, go to "Wireless Network" on page 30 to set up the product's wireless network connection. 10 . To upgrade the software, select Update now, and then press the E button. To skip the upgrade, select Update later, press the E button, and go to Step 12. | NOTE |  If you skipped network set up, you must skip Software Update also. 11 . If there is a Software Update available, the product downloads and installs the upgrade. This can take some time. If there is no Software Update available, the "There are no new software updates for you to download. You already have the most up to date version." message appears. And then press the E button. The TV Aspect Ratio screen appears. Initial Settings > TV Aspect Ratio Previous Next Set to match the type of television connected. 16:9 Original 16:9 Full 4:3 Letter Box 4:3 Pan-Scan Select when connecting to a 16:9 TV Screen. All content will be displayed at original aspect ratio. Content formatted in 4:3 will be displayed with black bars on left and right. 12 . Using the ▲▼ buttons, select the aspect ratio that matches your screen, and then press the E button. Select Next, and then press the E button. You have four choices: 16:9 Original - For widescreen TVs. Displays widescreen pictures in their original 16:9 format and 4:3 pictures (the old, standard format) in 4:3 pillar box format with black bars on the left and right. 16:9 Full - For widescreen TVs. Displays widescreen pictures in their original 16:9 format and expands 4:3 pictures to fill the