Input/Output

This section describes the user tools in the Input/Output menu under Copier / Document Server Features.

Default settings are shown in bold type.

Switch to Batch

You can select to have Batch mode or SADF mode displayed when you press [Special Original].

The default setting is Batch.

Settings made on the main and sub-machines do not affect the connect copy.

SADF Auto Reset

In SADF mode, an original must be set within a specified time after the previous original has been fed.

The default setting is 5 second(s).

You can adjust this time from 3 to 99 seconds in increments of 1 second.

The main machine applies the setting that has been made on it. Sub-machine settings do not affect connect copy.

Rotate Sort: Auto Paper Continue

Specify to continue copying when paper of the required orientation has run out during rotate sort.

The default setting is Off.

On
Copying continues using copy paper of a different orientation. The copy job will finish even if you have left the machine.
Off
When paper of the required orientation runs out, the machine stops copying and prompts you to supply copy paper. After you have loaded paper, the machine will continue copying.

The main machine applies the setting that has been made on it. Sub-machine settings do not affect connect copy.

Copy Eject Face Method in Glass Mode

You can specify the way in which copies are delivered when copying an original placed on the exposure glass.

The default setting is Face Up.

Settings made on the main and sub-machines do not affect the connect copy.

Copy Eject Face Method in Bypass Mode

You can specify the way in which copies are delivered when copying in bypass mode.

The default setting is Face Up.

Settings made on the main and sub-machines do not affect the connect copy.

Memory Full Auto Scan Restart

When memory becomes full while scanning originals, the machine can make copies of scanned originals first, and then automatically proceed scanning remaining originals.

The default setting is Off.

On
You can leave the machine unattended to make copies, but sorted pages will not be sequential.
Off
When memory becomes full, the machine stops operation allowing you to remove the copy pages delivered on the output tray.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Letterhead Setting

If you select [Yes] in this function, the machine rotates the image correctly.

The default setting is No.

Orientation-fixed (top to bottom) or two-sided paper might not be printed correctly depending on how the originals and paper are placed.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Staple Position

Specify which staple type has priority to be shown on the initial display.

The Finisher SR4030, SR4050 or Booklet Finisher SR4040 is required to use this function.

When the Finisher SR4030 is installed:
The default setting for "Staple Position 1" is Top 1.
The default setting for "Staple Position 2" is Bottom 1.
The default setting for "Staple Position 3" is Left 2.
The default setting for "Staple Position 4" is Top 2.
When the Booklet Finisher SR4040 is installed:
The default setting for "Staple Position 1" is Top 1.
The default setting for "Staple Position 2" is Center.
The default setting for "Staple Position 3" is Left 2.
The default setting for "Staple Position 4" is Top 2.
When the Finisher SR4050 is installed:
The default setting for "Staple Position 1" is Top 1.
The default setting for "Staple Position 2" is Bottom 1.
The default setting for "Staple Position 3" is Left 2.
The default setting for "Staple Position 4" is Top 2.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Punch Type

Specify which punch type has priority to be shown on the initial display.

The Finisher SR4030, SR4050 or Booklet Finisher SR4040 is required to use this function.

The default setting for "Punch Type 1" is 3 Holes Left.

The default setting for "Punch Type 2" is 3 Holes Top.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Simplified Screen: Finishing Types

You can select which key is displayed with higher priority for "Finishing Types" on the Simplified Screen.

The default setting for "Simplified Screen: Finishing Types 1" has not been set.

The default setting for "Simplified Screen: Finishing Types 2" has not been set.

The default setting for "Simplified Screen: Finishing Types 3" has not been set.

Settings made on the main and sub-machines do not affect the connect copy.

The connect copy function is not available from the simple display.

Z-fold Output Tray

Specify the tray where Z-fold prints are output to.

The default setting is Folding Unit Tray.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Half Fold Settings

Specify each settings of half fold.

Fold Orientation
Specify the fold orientation of prints.
The default setting is Right-Left.
Print Side
Specify which side of sheets is printed on.
The default setting is Inside.
Multi-sheet Fold
Specify whether or not to fold multiple sheets together.
The default setting is Off.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Letter Fold-out Settings

Specify each settings of letter fold-out.

Fold Orientation
Specify the fold orientation of prints.
The default setting is Right-Left.
Open Orientation
Specify the opening orientation of prints.
The default setting is Open to Right (Open to Top).
Multi-sheet Fold
Specify whether or not to fold multiple sheets together.
The default setting is Off.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Letter Fold-in Settings

Specify each settings of letter fold-in.

Fold Orientation
Specify the fold orientation of prints.
The default setting is Right-Left.
Open Orientation
Specify the opening orientation of prints.
The default setting is Open to Right (Open to Top).
Print Side
Specify which side of sheets is printed on.
The default setting is Inside.
Multi-sheet Fold
Specify whether or not to fold multiple sheets together.
The default setting is Off.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Double Parallel Fold Settings

Specify each settings of double parallel fold.

Fold Orientation
Specify the fold orientation of prints.
The default setting is Right-Left.
Open Orientation
Specify the opening orientation of prints.
The default setting is Open to Right (Open to Top).
Print Side
Specify which side of sheets is printed on.
The default setting is Inside.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Gate Fold Settings

Specify each settings of gate fold.

Fold Orientation
Specify the fold orientation of prints.
The default setting is Right-Left.
Print Side
Specify which side of sheets is printed on.
The default setting is Inside.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.