Destination: USER-TASK Routing code: Weight:
Warranty : NO
SRVCOPY Copyright (C) '(&00)' '(&01)' All Rights Reserved
SRVLOAD
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SRVLOAD Program '(&00)',Version '(&01)' of '(&02)' loaded
SRV0001
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0001 BAD SPSERVE SYNTAX FILE VERSION
SRV0002
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SRV0002 CLUSTER OR SERVER NOT ACCESSIBLE
Meaning
The given CLUSTER or SERVER is not accessible.
SRV0003
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SRV0003 DPRINT PRINTER (&00) NOT DEFINED
Meaning
The given printer is not found in the DPRINT configuration.
SRV0004
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SRV0004 INFORMATION operand value not allowed
Meaning
INFORMATION=*VERSION is not allowed when processing
a user SPOOL PARAMETERS file, i.e. when the
//OPEN-PARAMETER-FILE <filename> statement has been issued.
Response
Correct statement and retry.
SRV0401
Destination: USER-TASK, CONSOLE Routing code: S Weight: 99
Warranty : NO
SRV0401 FILE '$SYSSPOOL.SPOOL.PARAMETERS' IS BEING PROCESSED
Meaning
The SPOOL parameters start-up procedure is processing
the file $SYSSPOOL.SPOOL.PARAMETERS.
SRV0402
Destination: USER-TASK, CONSOLE Routing code: S Weight: 99
Warranty : NO
SRV0402 FILE '$SYSSPOOL.SPOOL.PARAMETERS': PROCESSING COMPLETED
Meaning
The SPOOL parameters start-up procedure has finished processing the file
$SYSSPOOL.SPOOL.PARAMETERS.
SRV0403
Destination: USER-TASK, CONSOLE Routing code: S Weight: 98
Warranty : NO
SRV0403 '(&00)' ERROR '(&01)' IN FILE '(&02)'. RETRY? (Y=YES; N=NO: A 'PRESET' FILE IS CREATED FOR THIS SESSION)
Meaning
A DMS error has occurred while processing the file
$SYSSPOOL.SPOOL.PARAMETERS or its copy (used for start-up processing).
For more detailed information about the DMS error code, enter /HELP-MSG
in system mode or see BS2000 manual 'System Messages'.
(&00): DMS macro name
(&01): DMS macro return code
(&02): file name: $SYSSPOOL.SPOOL.PARAMETERS or
$SYSSPOOL.SPOOL.PARAMETERS.COPY.
Response
Y: The retry operation may begin. At this point the operator should have
repaired the file $SYSSPOOL... by a DMS operation or imported another
one.
N: No retry is attempted. The system will then provide default values for
the SPOOL parameters and a new file $SYSSPOOL.SPOOL.PARAMETERS.PRESET
will be created to store these values.
SRV0404
Destination: USER-TASK, CONSOLE Routing code: S Weight: 99
Warranty : NO
SRV0404 PRECEDING ERROR PREVENTS SPOOL PARAMETER FILE UPDATE. ONLY THE TABLE IS UPDATED
Meaning
An error has occurred during SPOOL parameter processing which prevents the
SPOOL parameter file update. It has been reported by message SPM0419 and
a SERSLOG entry has been made.
Due to this error, only the tables could be updated.
The SPOOL session may continue, but any further attempt to update the
SPOOL
parameters via a command will only modify the table (unless the file
becomes accessible again), i.e. the update is valid only for the
current session.
Response
The file will be repaired at the next SPOOL start-up if possible.
All modifications made from now on until the end of the session must be
re-entered after the next start-up.
SRV0405
Destination: USER-TASK, CONSOLE Routing code: S Weight: 99
Warranty : NO
SRV0405 USER NOT AUTHORIZED TO USE COMMAND '(&00)'. COMMAND REJECTED
Meaning
This message appears in the following cases:
/ADD-SPOOL-DEVICE: either the user is not a system administrator,
or the specified user ID does not exist
/MOD-SPOOL-DEVICE: either the user is not an RSO device administrator,
or the specified terminal cannot be used for
administration tasks,
or the specified user ID does not exist
/SHOW-SPOOL-DEVICE: the user is not administrator of the device or his/her
terminal is not the administration terminal
/ADD-SPOOL-FORM : the user is not an RSO device administrator
/MOD-SPOOL-FORM : the user is not the owner of the form
/SHOW-SPOOL-FORM : the user is not the owner of the form
/ADD-SPOOL-CHAR : the user is not an RSO device administrator
/MOD-SPOOL-CHAR : the user is not the owner of the character set
/SHOW-SPOOL-CHAR : the user is not the owner of the character set
/ADD-PRINTER-POOL: the user is not a system administrator
/MOD-PRINTER-POOL: the user is not a system administrator.
SRV0406
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0406 '(&00)' OPERAND INVALID IN '(&01)' COMMAND. COMMAND IGNORED
Response
Correct the command and try again.
SRV0407
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0407 POSITIONAL OPERAND INVALID IN '(&00)' COMMAND. COMMAND IGNORED
Response
Correct the command and try again.
SRV0408
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0408 VALUE '(&00)' INVALID FOR '(&01)' OPERAND IN '(&02)' COMMAND. COMMAND IGNORED
Response
Correct the command and try again.
SRV0409
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0409 REQUIRED OPERAND '(&00)' MISSING OR EMPTY IN '(&01)' COMMAND. COMMAND IGNORED
Response
Correct the command and try again.
SRV0410
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0410 CONFLICT BETWEEN '(&00)' AND '(&01)' OPERANDS IN '(&02)' COMMAND. COMMAND IGNORED
Response
Correct the command and try again.
SRV0411
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0411 NO DEVICE OR NONE OF THE SPECIFIED DEVICES EXISTS. COMMAND OR STATEMENT NOT PROCESSED
Meaning
The SPOOL parameters device table does not contain any
information about the specified device(s).
SRV0412
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0412 NO FORM OR NONE OF THE SPECIFIED FORMS EXISTS. COMMAND OR STATEMENT NOT PROCESSED
Meaning
The SPOOL parameters form table does not contain any
information about the specified form(s).
SRV0413
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0413 NO CHARACTER-SET OR NONE OF THE SPECIFIED CHARACTER-SETS EXISTS. COMMAND OR STATEMENT NOT PROCESSED
Meaning
The SPOOL parameters character-set table does not contain any
information about the specified character-set(s).
Response
NONE
SRV0414
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0414 END OF DISPLAY. '(&00)' COMMAND TERMINATED
Meaning
No more devices, forms or character sets could be found in the table.
SRV0415
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0415 ELEMENT TO BE MODIFIED DOES NOT EXIST. COMMAND OR STATEMENT NOT PROCESSED
Meaning
The element specified in the /MODIFY-type command or the
//MODIFY-type statement does not exist (type can be
DEVICE or FORM or CHARACTER-SET or PRINTER-POOL).
SRV0416
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0416 ELEMENT TO BE DELETED DOES NOT EXIST. COMMAND TERMINATED
Meaning
The element specified in a /REMOVE-... command does not exist.
SRV0417
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0417 ELEMENT TO BE CREATED ALREADY EXISTS. COMMAND TERMINATED
Meaning
The element specified in an /ADD-... command exists already.
Possible error cause in the case of an /ADD-SPOOL-DEVICE command:
An existing element name may be
- a mnemonic existing in the PDT,
- a remote batch processing station existing in the BSET,
- one of the reserved names CENTRAL, REMOTE, T9N, T9P, T9G.
SRV0418
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0418 ELEMENT '(&00)' DOES NOT EXIST. COMMAND OR STATEMENT CONTINUES
Meaning
command statement
/MODIFY-SPOOL-FORM //MODIFY-SPOOL-FORM
/REMOVE-SPOOL-FORM //REMOVE-SPOOL-FORM
//COPY-SPOOL-FORM
//COPY-SPOOL-DEVICE
//COPY-SPOOL-CHARACTER-SET
(&00): element name which can be a device name or a form name
or a character set name or a device type if DEVICE=ALL
has been specified.
SRV0419
Destination: USER-TASK, CONSOLE Routing code: S Weight: 99
Warranty : NO
SRV0419 SPOOL PARAMETERS INTERNAL ERROR '(&00)'. ERROR LOGGING SEQUENCE NUMBER IS '(&01)'. PROCESSING CONTINUES
Meaning
(&00): 0001: invalid record in file upon start-up
0002: logic error in /ADD command
0003: DMS error
0004: criterion list error
0005: class 4 memory allocation error
0006: logic error in /MODIFY or /REMOVE command
0007: display error
0008: message error
0009: SPMINTE error
0010: lock error on parameter table
0011: unlock error on parameter table
0012: class 5 memory allocation error
0013: class 5 memory release error
(&01): error logging sequence number.
SRV0420
Destination: USER-TASK, CONSOLE Routing code: S Weight: 99
Warranty : NO
SRV0420 SPOOL PARAMETERS RECOVERY STARTED
Meaning
An error was detected in the SPOOL parameter file or table.
SRV0421
Destination: USER-TASK, CONSOLE Routing code: S Weight: 99
Warranty : NO
SRV0421 SPOOL PARAMETERS RECOVERY COMPLETED
Meaning
The SPOOL parameters recovery has been terminated normally.
SRV0422
Destination: USER-TASK, CONSOLE Routing code: S Weight: 99
Warranty : NO
SRV0422 '(&00)' ERROR '(&01)' DURING SPOOL PARAMETERS RECOVERY. RECOVERY ABORTED
Meaning
A system error was detected during SPOOL parameters recovery.
(&00): macro name
(&00): macro error code.
SRV0423
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0423 NO CLASS 4 MEMORY AVAILABLE. '(&00)' COMMAND TERMINATED
Meaning
The SPOOL parameters memory could not be extended.
Response
Try again later.
SRV0424
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0424 SPECIFIED ELEMENT '(&00)' NOT DEFINED. STATEMENT NOT PROCESSED
Meaning
One of the elements defined in a SPOOL parameter statement does not exist.
(&00): nonexistent user ID in the JOIN file, or undefined character set
or device in the SPOOL.PARAMETERS file or PRFILE, or device or
pool not defined in the SPOOL.PARAMETERS file but entered as the
default value under DESTINATION.
Response
Specify the
- missing user ID by means of the /ADD-USER command
- missing character set in the table by means of ADD-SPOOL-CHARACTER-SET
- missing device name in the table by means of ADD-SPOOL-DEVICE
- missing pool in the file by means of ADD-PRINTER-POOL
- missing character set in the system PRFILE using PRM
and re-enter the statement.
SRV0425
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0425 NO USER MEMORY AVAILABLE. COMMAND TERMINATED
Meaning
During a /SHOW-... command, a request for class 5 memory was unsuccessful.
The command cannot be executed.
Response
Release some class 5 memory and retry the command.
SRV0426
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0426 USER NOT AUTHORIZED TO ACCESS RECORD WITH DEVICE TYPE '(&00)'. PROCESSING CONTINUES
Meaning
The form specified for a given device type in the //MODIFY-SPOOL-FORM,
//REMOVE-SPOOL-FORM or //ADD-SPOOL-FORM statement belongs to another user,
namely the SPOOL administrator or another RSO device administrator.
This specification is ignored but the statement is processed with the
other operands.
SRV0427
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0427 ACTIVE DEVICE MAY NOT BE ADDED, MODIFIED OR REMOVED. COMMAND OR STATEMENT REJECTED
Meaning
One of the following commands or statements has been entered for an active
local device or an active RSO device:
ADD-SPOOL-DEVICE
MODIFY-SPOOL-DEVICE
REMOVE-SPOOL-DEVICE.
Response
Release the device via a /STOP-PRINTER-OUTPUT command before re-entering
the command/statement.
SRV0428
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0428 INCONSISTENCY BETWEEN SPOOL PARAMETER FILE AND TABLE. CONTINUING WITH TABLE ONLY
Meaning
A logic error occurred while updating the SPOOL parameter file. Due to
this
error, only the table is updated but not the file.
Possible error cause:
A SPOOL parameter record exists
- in the table and not in the file (MODIFY-SPOOL-xxx or REMOVE-SPOOL-xxx
command or statement)
- in the file and not in the table (ADD-SPOOL-xxx command or statement).
xxx: FORM, DEVICE or CHARACTER-SET.
SRV0429
Destination: USER-TASK, CONSOLE Routing code: S Weight: 99
Warranty : NO
SRV0429 DMS ERROR CODE '(&00)' WHILE CREATING OR MODIFYING SPOOL PARAMETER FILE. ONLY TABLE PROCESSED. IN SYSTEM MODE: /HELP-MSG DMS(&00)
Meaning
An error has occurred during SPOOL parameter processing which prevents the
SPOOL parameter file update.
Any further modifications to the SPOOL parameter file may lead to
message SPM0404.
For more detailed information about the DMS error code enter /HELP-MSG in
system mode or see the BS2000 manual 'System Messages'.
SRV0430
Destination: CONSOLE Routing code: S Weight: 99
Warranty : NO
SRV0430 ERROR WHILE PROCESSING SPOOL PARAMETER FILE. 'PRESET' FILE IS CREATED FOR THIS SESSION
Meaning
All parameters of the newly created SPOOL.PARAMETERS.PRESET file
are assigned default values.
Response
The SPOOL administrator must check this file and update
it if it is necessary.
SRV0431
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0431 FORM '(&00)' ALREADY SPECIFIED FOR DEVICE TYPE '(&01)'. COMMAND PROCESSING CONTINUES
SRV0432
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0432 '(&00)' IS STANDARD CHARACTER SET IN FORM '(&01)'. '(&02)' COMMAND REJECTED
Meaning
The character set (&00) may not be removed from the SPOOL parameter table
because it is still used as default character set in the form (&01).
(&00): character set name
(&01): form name.
Response
Use a different character set in the form or remove the form,
then retry the command.
SRV0433
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0433 '*ALL' IS NOT ALLOWED WITHIN A LIST. CORRECT '(&00)' COMMAND
Meaning
In a /SHOW-... command, the operand can be an identifier, *ALL or a list
of identifiers.
The value *ALL is not allowed within a list.
SRV0434
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0434 TOO MANY ENTRIES IN LIST GIVEN FOR '(&00)' OPERAND. CORRECT COMMAND
SRV0435
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0435 WARNING: THE SPOOL PARAMETER FILE IS RESET TO ITS PREVIOUS STATE. MODIFICATIONS OF LAST SESSION ARE LOST
Meaning
The SPOOL.PARAMETERS file could not be opened. SPOOL uses a copy
which has been saved at the beginning of the previous session.
Response
All the modifications which have been made during the previous
SPOOL session must be entered again.
SRV0436
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0436 WARNING: NEW SPOOL PARAMETER FILE CREATED WITH DEFAULT VALUES
Meaning
No SPOOL.PARAMETERS file from the previous session could be opened.
SPOOL creates a new one with all default values.
SRV0437
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0437 INCORRECT VALUE FOR 'RBP-STATION-LIMIT': 'BSET' TABLE CONTAINS ONLY (&00) ENTRIES. COMMAND REJECTED
Meaning
(&00): number of entries in the BSET (Batch Station Entry Table).
SRV0438
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0438 SPOOL PARAMETER CONVERSION IN PROCESS. RETRY COMMAND LATER
Meaning
The SPOOL administrator has started a conversion of the
SPOOL parameter file. During this time, the SPOOL parameters can
still be used, but not modified.
SRV0439
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0439 DMS ERROR '(&00)' FOR FILE '(&01)'. STATEMENT NOT EXECUTED. IN SYSTEM MODE: /HELP-MSG DMS(&00)
Meaning
For more detailed information about the DMS error code enter /HELP-MSG in
system mode or see the BS2000 manual 'System Messages'.
SRV0440
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0440 WRONG VERSION OF SPOOL PARAMETER FILE. STATEMENT NOT EXECUTED
Meaning
The version of the SPOOL parameter file does not match any known SPOOL
version. SPSERVE cannot process this file.
Possible error cause:
- the parameter file was generated by an intermediate SPOOL version that
is not supported
- the parameter file has been overwritten.
Response
Use the appropriate SPOOL parameter file.
If a new SPOOL parameter file with this name is to be generated, the
existing file must be deleted by means of the /DELETE-FILE command.
SRV0441
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0441 SPECIFIED FILE NO SPOOL PARAMETER FILE. STATEMENT REJECTED
Meaning
The file specified in the //ASSIGN-PARAMETER-FILE statement exists
but does not have the format of a SPOOL.PARAMETERS file.
Response
If a new SPOOL parameter file is to be created under the specified name,
first erase the file with this name by means of the /DELETE-FILE command.
SRV0442
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0442 DEVICE TO BE MODIFIED IS BEING USED IN ONE OR MORE POOLS. COMMAND REJECTED
SRV0443
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0443 INTERNAL ERROR '(&00)'. PLEASE CONTACT MAINTENANCE SERVICE
Meaning
(&00):
3 : SPOOL was not able to process the request
4 : an invalid address has been passed to SPOOL
6 : invalid record code
7 : V field too short
8 : invalid record length
9 : invalid action code
16 : LOCK ERROR ON SPOOL PARAMETERS
12 : no memory available
97 : error while processing POOL statement
98 : STXIT error
99 : SDF error.
SRV0444
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0444 ILLEGAL VALUE FOR '(&00)' OPERAND IN '(&01)' STATEMENT. STATEMENT NOT PROCESSED
Meaning
SPOOL has detected one of the following errors in the GEN record:
- the specified RBP station limits are greater than the values generated
in the system in the batch station entry table (BSET).
- SPOOLOUT-SIZE=LINE and LINE-FACTOR=0 have been specified.
- SPOOLOUT-SIZE has been changed from LINES to PAM-PAGES and
LINE-FACTOR not equal to 0 has been specified.
- DESTINATION=REMOTE has been specified and the printer name is either
missing or not defined in the SPOOL.PARAMETERS file.
- DESTINATION=REMOTE applies and the specified printer is a local one.
- DESTINATION=POOL has been specified and the pool name is either missing
or not defined in the SPOOL.PARAMETERS file.
- DESTINATION has been changed from REMOTE or POOL to LOCAL and a
device name or pool name has been specified.
SRV0445
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0445 SYSTEM ERROR: ERROR IN BOURSE PROCESSING. THE SPOOL PARAMETERS CANNOT BE USED ANY MORE
Meaning
No new job can be scheduled. No new /PRINT-FILE command can be accepted.
Response
Unload the SPOOL subsystem, load it again and retry.
SRV0446
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0446 WARNING: DEVICE '(&00)' ALREADY IN POOL. PROCESSING CONTINUES
SRV0447
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0447 WARNING: DEVICE '(&00)' NOT IN POOL. PROCESSING CONTINUES
SRV0448
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0448 CONVERSION TO VERSION '(&00)' TERMINATED WITHOUT ERRORS
Meaning
SPSERVE sensed that the existing SPOOL parameter file did not correspond
to the latest version; conversion was effected automatically.
(&00): new version of the SPOOL parameter file.
SRV0449
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0449 MORE THAN ONE VALUE HAS BEEN SPECIFIED FOR ONE OPERAND IN '(&00)' COMMAND OR STATEMENT. COMMAND OR STATEMENT REJECTED
Meaning
The operand can be either CHARACTER-SET-NAME, DEVICE-NAME,
FORM-NAME or DEVICE-TYPE.
(&00) : command or statement name.
SRV0450
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0450 CODE OR SYMBOL TO BE MODIFIED NOT FOUND IN FILE. STATEMENT NOT EXECUTED
SRV0451
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0451 SPECIFIED DEVICE NOT IN FILE. STATEMENT NOT EXECUTED
SRV0452
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0452 SPOOL PARAMETERS UPDATE IN PROGRESS. RETRY COMMAND OR STATEMENT LATER
Meaning
The SPOOL administrator has started a migration or a merge on
the SPOOL PARAMETERS file with SPSERVE. During this time, the
SPOOL PARAMETERS are locked.
SRV0453
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0453 PROGRAM NOT DEFINED IN SDF. PROGRAM ABORTED
Meaning
SPSERVE program not defined in the SPSERVE syntax file. The statements
were rejected.
SRV0454
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0454 SDF NOT LOADED. PROGRAM ABORTED
SRV0455
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0455 NO POOL FOUND. COMMAND OR STATEMENT REJECTED
SRV0456
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0456 NO OUTPUT RECORD FOUND. STATEMENT NOT EXECUTED
SRV0457
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0457 NO TABLE RECORD FOUND. STATEMENT NOT EXECUTED
SRV0458
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0458 DO YOU WANT TO TERMINATE MIGRATION? REPLY (Y=YES; N=NO)
Response
Y: migration will be ended.
N: migration will be continued.
SRV0459
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0459 UNKNOWN DEVICE OR POOL SPECIFIED FOR 'DESTINATION'. STATEMENT NOT EXECUTED
SRV0460
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0460 NONE OF THE SPECIFIED DEVICES EXISTS OR IS OF THE APPROPRIATE TYPE (LOCAL OR REMOTE). STATEMENT TERMINATED
Meaning
Possible reasons:
- none of the specified devices exists
- all specified devices are LOCAL but the pool is REMOTE
- all specified devices are REMOTE but the pool is LOCAL.
SRV0461
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0461 MISSING DISPLAY RECORD(S) IN THE SPOOL.PARAMETERS FILE. COMMAND OR STATEMENT NOT PROCESSED
SRV0462
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0462 DEVICE TYPE '(&00)' UNKNOWN. COMMAND NOT EXECUTED
Meaning
In an /ADD-SPOOL-DEVICE or an /ADD-SPOOL-FORM command a device type has
been specified that is neither defined in the command syntax nor
a special user device type.
SRV0463
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0463 WARNING: THIS ELEMENT DOES NOT EXIST. '//MODIFY' STATEMENT REQUIRED TO CREATE IT
Meaning
In an //EDIT statement an element name has been specified which does
not match any existing element.
Response
If an element is to be created with the element name entered in the
//EDIT statement, a //MODIFY statement is required.
SRV0465
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0465 NO POOL EXISTS. COMMAND NOT PROCESSED
SRV0466
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0466 TOO MANY INSERTS IN DISPLAY RECORD. STATEMENT REJECTED
Meaning
A display record cannot contain more than 30 inserts.
Response
Create an additional display record for the surplus inserts.
SRV0467
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0467 CODE OR SYMBOL TO BE ADDED IS ALREADY IN TABLE RECORD. STATEMENT REJECTED
SRV0468
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0468 CODE OR SYMBOL TO BE REMOVED IS NOT IN TABLE RECORD. STATEMENT REJECTED
SRV0469
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0469 NAME ALREADY ASSIGNED TO PRINTER POOL. COMMAND REJECTED
SRV0470
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0470 NAME ALREADY ASSIGNED TO A DEVICE. COMMAND REJECTED
SRV0471
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0471 NEITHER 'TITLE' NOR 'INSERT' OPERAND ENTERED IN //ADD-DISPLAY-MODEL. NO RECORD CREATED
Meaning
A display record without values for TITLE and INSERT is useless.
SRV0472
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0472 NO USER MEMORY AVAILABLE. STATEMENT NOT PROCESSED
SRV0473
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0473 SPSERVE IS UNABLE TO PROCESS THE CURRENT SPOOL VERSION. STATEMENT NOT EXECUTED
Meaning
The loaded SPOOL version is < 2.4A.
SRV0474
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0474 DEVICE TYPE UNDEFINED IN SYNTAX FILE. STATEMENT REJECTED
Meaning
The //EDIT statement is rejected.
Response
Use //ADD or //MODIFY statement.
SRV0475
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0475 TOO MANY CODES OR SYMBOLS IN THE TABLE RECORD. STATEMENT REJECTED
Meaning
A table record must not contain more than 125 codes or symbols.
Response
Create an additional table record for the surplus codes or symbols.
SRV0476
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0476 TBL RECORDS MISSING IN THE SPOOL PARAMETER FILE. COMMAND NOT PROCESSED
Meaning
The SPOOL parameter file does not contain the necessary TBL records,
thus preventing most of the SPM commands from being executed.
Response
Contact the SPOOL administrator.
SRV0477
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0477 LOCAL PRINTER '(&00)' MUST NOT BE INCLUDED IN RSO DEVICE POOL. PROCESSING CONTINUES
Meaning
The device (&00) is not in the REMOTE state.
The device is ignored and processing continues.
(&00): device name or list of devices.
SRV0478
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0478 SPOOL PARAMETER FILE CONTAINS NO CORRECTIONS. STATEMENT NOT PROCESSED
SRV0479
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0479 //MERGE STATEMENT NOT EXECUTED
Meaning
Processing of the //MERGE statement has been interrupted, either by the
user or by an external event in conjunction with a message.
The SPOOL.PARAMETERS file retains the status it had before the
//MERGE statement was issued.
SRV0480
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0480 POOL RECORDS (POL AND DVP) NOT COPIED. PROCESSING CONTINUES
Meaning
The file to be merged by the //MERGE statement contains
printer pool definitions (POL and DVP records).
These records are not added to the SPOOL.PARAMETERS file.
SRV0481
Destination: USER-TASK Routing code: Weight: 98
Warranty : NO
SRV0481 DO YOU WANT TO TERMINATE //MERGE PROCESSING? REPLY (Y=YES; N=NO)
Response
Y: merge will be ended.
N: merge will be continued.
SRV0482
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0482 TO ACCESS CURRENTLY ACTIVE SPOOL PARAMETER FILE, SPECIFY KEYWORD '*SPOOL-PARAMETERS' IN //ASSIGN-PARAMETER-FILE STATEMENT
SRV0483
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0483 DEVICE TYPE OPERAND NECESSARY TO MODIFY *STD DEVICE RECORD. STATEMENT NOT PROCESSED
SRV0484
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0484 'SPSERVE' VERSION NOT COMPATIBLE. STATEMENT NOT PROCESSED
Meaning
Incompatibility between the SPSERVE version and the internal version
of the SPOOL.PARAMETERS file.
Response
Use the appropriate SPSERVE version and retry.
SRV0485
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0485 SPOOL PARAMETER FILE OF CURRENT SPOOL SESSION IS 'SPOOL.PARAMETERS.PRESET' FILE. MIGRATION ABORTED
SRV0486
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0486 AT LEAST ONE RECORD ALREADY PRESENT IN SPOOL PARAMETER FILE AND WILL NOT BE REPLACED BY //COPY OR //MERGE STATEMENT. PROCESSING CONTINUES
Meaning
A //COPY or //MERGE statement with OVERWRITE=NO has been issued.
Any existing records are not replaced.
SRV0487
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0487 AT LEAST ONE RECORD FROM FILE TO BE MERGED HAS SMALLER VERSION NUMBER THAN EXISTING RECORDS AND IS NOT REPLACED. PROCESSING CONTINUES
Meaning
Records from the file to be merged are not copied if they have a smaller
version number than the corresponding records in the SPOOL parameter file.
SRV0488
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0488 FILE IS EMPTY OR NOT FOUND. STATEMENT NOT PROCESSED
SRV0489
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0489 VALUE OF 'DESTINATION' OPERAND (IN 'PRINT-COMMAND-DEFAULTS' OPERAND GROUP OF //MODIFY-SPOOL-PARAMETERS STATEMENT) IS 'POOL'. 'GEN' RECORD NOT ACCEPTED. PROCESSING CONTINUES
Meaning
The value POOL is not permitted because the RSO device pools have not
been accepted by the //MERGE-SPOOL-PARAMETERS-FILE statement.
SRV0490
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0490 INSERT TO BE REMOVED FROM RCT RECORD DOES NOT EXIST. STATEMENT NOT PROCESSED
SRV0491
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0491 FILE TO BE COPIED IS CURRENTLY BEING PROCESSED. STATEMENT NOT EXECUTED
Meaning
The file to be copied is the one specified in the
//ASSIGN-PARAMETER-FILE statement.
SRV0492
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0492 SPECIFIED 'CHARACTER-SET-POSITION' CANNOT BE USED FOR THIS DEVICE TYPE. STATEMENT REJECTED
Meaning
The user has specified a CHARACTER-SET-POSITION in an //ADD-SPOOL-DEVICE
statement which is marked as NOT-USABLE in the *STD record. This means
that this hardware position does not physically exist for this device
type.
Response
If the *STD record is not correct or has ceased to be valid, contact
the SPOOL administrator and have the record corrected.
SRV0493
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0493 COPY STATEMENTS NOT ALLOWED IN DYNAMIC MODE. STATEMENT REJECTED
SRV0494
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0494 WARNING: DMS ERROR '(&00)' DURING ERASE MACRO ON FILE '(&01)'. IN SYSTEM MODE: /HELP-MSG DMS(&00)
Meaning
After the migration from PAM key to non PAM key, the original
SPOOL parameter file renamed &01 could not be erased.
For more detailed information about the DMS error code, enter /HELP-MSG in
system mode or see the BS2000 manual 'System Messages'.
SRV0495
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0495 SPOOL PARAMETERS INTERFACE: INTERNAL ERROR AT '(&00)'
Meaning
(&00): interface identification.
SRV0496
Destination: USER-TASK, CONSOLE Routing code: S Weight: 98
Warranty : NO
SRV0496 '(&00)' ERROR '(&01)' IN FILE '(&02)'. STATEMENT TERMINATED
Meaning
An error has occurred while processing the file
$SYSSPOOL.SPOOL.PARAMETERS or its copy (used for start-up processing).
(&00): DMS macro name
(&01): DMS macro return code
(&02): file name: $SYSSPOOL.SPOOL.PARAMETERS or
$SYSSPOOL.SPOOL.PARAMETERS.COPY.
SRV0497
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0497 VALUE SPECIFIED FOR '(&00)' NOT PERMITTED FOR THIS DEVICE TYPE. STATEMENT REJECTED
Meaning
Possible reasons for the error:
- In an //ADD- or //MOD-SPOOL-DEVICE statement, a DEVICE-CHARACTERISTIC
operand has an illegal value for this device type, or
- a DEVICE-INFORMATION operand has been specified in an //ADD-SPOOL-DEVICE
statement for a non-ND or non-HP printer, or
- a FORMS-OVERLAY-BUFFER operand has been specified for a non-HP
printer, or
- ROTATION=YES has been specified for a non-HP printer.
(&00): CHARACTER-SET-NUMBER or FORMS-OVERLAY-BUFFER or ROTATION.
SRV0498
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0498 NO ELEMENT IN INPUT FILE CORRESPONDS TO SPECIFIED NAMES. STATEMENT NOT PROCESSED
Meaning
The input file does not contain any character set, form or device
- with the specified name
- whose name corresponds to the specified wildcard entry.
SRV0499
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0499 ILLEGAL VALUE FOR OPERAND '(&00)' IN STATEMENT '(&01)' FOR DEVICE TYPE '(&02)'. STATEMENT REJECTED
Meaning
SPOOL has detected one of the following errors in the FORM record:
- DEVICE-TYPE not equal to EMULATED and PREFORM has been specified;
- FORM has been specified for a local printer by a user other than TSOS;
- FORM-NAME not equal to *STD has been specified for printer type
CENTRAL or REMOTE;
- ROTATION-CONTROL has been specified with a printer type other than
9022 or 9025 or 9021 or 9022-200 or 9000-PCL or HP-PRINT or HP90-PRINT;
- ROTATION-CONTROL has been specified without ROTATION-CHAR-SET for
an RSO printer;
- ROTATION-CONTROL=SPACING has been specified for a local printer;
- ROTATION-CONTROL=SPACING and LINE-SIZE * LPI/10 < channel1-P have
been specified;
- ROTATION-CHAR-SET has been specified for a local printer;
- ROTATION-CHAR-SET has been specified but ROTATION-CONTROL=NONE
applies;
- CONTROL=LOOP has been specified without a LOOP name;
- CONTROL=SPACING has been specified without an LPI or CHANNEL1-POS
specification;
- VERTICAL-CONTROL=SPACING has been specified for a local printer;
- VERTICAL-CONTROL=SPACING and PAGE-SIZE * LPI/10 < channel1-P have
been specified;
- DEVICE-TYPE=8415 or =8418 and TRAILER-PAGE=INFO;
- VERTICAL-CONTROL not equal to NONE for APA printer;
- VERTICAL-CONTROL=NONE for non-APA printer;
- DEVICE-TYPE=2050-APA or =2090-APA and CHARACTER-SET not equal to
*NONE;
- DEVICE-TYPE not equal to 2050-APA nor 2090-APA and CHARACTER-SET=
*NONE;
- DEVICE-TYPE=2050-APA or =2090-APA and BAND-ID is specified;
- DEVICE-TYPE=RSO or APA and CHARACTER-IMAGE is specified;
- DEVICE-TYPE not equal to LP65 and TWO-UP processing is specified;
- DEVICE-TYPE not equal to LP65 nor APA and PRINTER-RESOURCES is
specified;
- DEVICE-TYPE=LP65 and PRINTER-RESOURCES not equal to LP65;
- DEVICE-TYPE=2050-APA or =2090-APA and PRINTER-RESOURCES not equal
to APA.
LPI: lines per inch.
SRV0500
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0500 NO *STD RECORD EXISTS FOR THE SPECIFIED DEVICE TYPE. STATEMENT NOT PROCESSED
SRV0501
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0501 INCORRECT 'LIST' OR 'RECORD BIT' OR 'MIXED DISPLAY' INSERT POSITIONING. STATEMENT NOT PROCESSED
Meaning
Positioning must be to the insert itself and not its extension.
SRV0502
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0502 NOT ENOUGH SPACE FOR 'LIST' OR 'RECORD BIT' OR 'MIXED DISPLAY' INSERT. STATEMENT TERMINATED
Meaning
Only one position is available, but a LIST or RECORD BIT or
MIXED DISPLAY insert needs two positions.
Response
Create a new RCT record.
SRV0503
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0503 OUTPUT MODE 'WRITE-BIT-LIST', 'FIND-BIT-IN-FIELD' OR 'INTERPRET-BIT-LIST' ONLY ALLOWED WITH 'ORIGIN=RECORD-BIT'. STATEMENT REJECTED
SRV0504
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0504 'TBL-STATE=NEW' AND RECORD PRESENT OR 'TBL-STATE=UPDATE' AND RECORD NOT PRESENT. STATEMENT REJECTED
SRV0505
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0505 AT LEAST ONE RECORD FROM FILE TO BE MERGED OR COPIED HAS DIFFERENT LENGTH FROM EXISTING RECORDS AND IS NOT ACCEPTED. PROCESSING CONTINUES
Meaning
Records from the file to be merged are not copied or merged if they have a
different length from the corresponding records in the SPOOL parameter
file.
SRV0506
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0506 ERROR WHILE PROCESSING THE 'TBL' RECORD ASSOCIATED WITH THE 'RCT' RECORD
SRV0507
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0507 SPECIFIED STRING TOO LONG FOR SPECIFIED START POSITION. STATEMENT REJECTED
Meaning
The area into which the string is to be moved is 79 bytes long.
The start position plus the string length may not exceed this value.
Response
Modify the START value or the string length.
SRV0508
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0508 'DESTINATION=REMOTE' BUT SPECIFIED PRINTER DOES NOT EXIST. COMMAND REJECTED
SRV0509
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0509 VALUE 'NO' IS GIVEN FOR THE 'HP' OPERAND, BUT 'F-O-B' IS NOT '0', 'C-S-N' IS NOT '4', OR 'ROTATION' IS NOT 'NO'. STATEMENT TERMINATED
Meaning
The internal validation has determined that the GEN record contains a
- FORMS OVERLAY BUFFER (F-O-B) different from 0 and/or
- CHARACTER-SET-NUMBER (C-S-N) different from 4 and/or
- ROTATION different from NO,
although the HP value is NO.
Such a GEN record can only be caused by a corrupted SPSERVE program.
This record is not accepted for the SPOOL.PARAMETERS file.
SRV0510
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0510 RSO PRINTER '(&00)' MUST NOT BE INCLUDED IN LOCAL DEVICE POOL. PROCESSING CONTINUES.
Meaning
The device (&00) is not local.
The device is ignored and processing continues.
(&00): device name or list of devices.
SRV0511
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0511 SPECIFIED DEVICE '(&00)' NOT DEFINED IN SPOOL.PARAMETERS FILE. PROCESSING CONTINUES
Meaning
The device (&00) specified in an //ADD-PRINTER-POOL or
//MODIFY-PRINTER-POOL statement is not present in the SPOOL.PARAMETERS
file.
SRV0512
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0512 SPOOL.PARAMETERS FILE HAS INVALID VERSION. CONVERSION NOT POSSIBLE UNDER THIS USER ID. STATEMENT NOT PROCESSED
Meaning
The version of the SPOOL.PARAMETERS file and the SPSERVE version do not
match. SPSERVE cannot convert the file as the user does not have the
necessary authorization.
Response
Either use an older version of SPSERVE or request the SPOOL
administrator to convert the file under his/her user ID using SPSERVE.
SRV0513
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0513 USER NOT AUTHORIZED TO ENTER //MERGE STATEMENT IN DYNAMIC MODE. STATEMENT NOT PROCESSED
Meaning
Only the SPOOL administrator is authorized to enter a //MERGE
statement for the SPOOL.PARAMETERS file currently used by SPOOL.
SRV0514
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SRV0514 //REMOVE-PRINTER-POOL or //MODIFY-PRINTER-POOL PRINTER-NAME=*REMOVE or //REMOVE-SPOOL-DEVICE for '(&00)' not allowed. Statement rejected
Meaning
The pool or device name (&00) is used as default destination
in the GEN record.
SRV0515
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0515 AN INTERNAL ERROR OCCURS DURING COMMAND OR STATEMENT PROCESSING. COMMAND OR STATEMENT NOT PROCESSED
Meaning
The information about the original error is sent to the console
or stored in the SERSLOG file.
SRV0516
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0516 CONFLICT BETWEEN '(&00)' AND '(&01)' OPERANDS IN '(&02)' COMMAND FOR DEVICE TYPE '(&03)'. COMMAND IGNORED
Meaning
(&00), (&01): operands in conflict.
Response
Correct the command and try again.
SRV0517
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0517 ILLEGAL VALUE FOR '(&00)' OPERAND IN '(&01)' STATEMENT. STATEMENT NOT PROCESSED
Meaning
This error message is displayed when SPOOL detects one of the
following errors in the DEVICE record:
- The specified printer name is illegal (CENTRAL, REMOTE, T9N, T9P, T9G,
a mnemonic device name specified in the PDT or
a remote batch processing station specified in the BSET).
- DEVICE-TYPE=LOCAL or =REMOTE or =NONE and DEVICE-NAME other than *STD
have been specified.
- DEVICE-TYPE=REMOTE and ACCESS=CHANNEL-1/CHANNEL-2 or =BUS have
been specified.
- DEVICE-TYPE=LOCAL and ACCESS not equal to CHANNEL-1 or CHANNEL-2 have
been specified.
- DEVICE-TYPE=EMULATED-PRINTER and ACCESS not equal to BUS have been
specified.
- DEVICE-TYPE=2050-APA-PRINTER or 2090-APA-PRINTER and access not
equal to CHANNEL-TYPE-2.
- DEVICE-TYPE=REMOTE and PROCESSOR-NAME=*HOST have been specified.
- DEVICE-TYPE=LOCAL or =EMULATED and a PROCESSOR-NAME other than *HOST.
- Only PROCESSOR-NAME or only STATION-NAME has been specified.
- DEVICE-TYPE=LOCAL or =EMULATED and two character images have been
specified.
- DEVICE-TYPE=2050-APA-PRINTER or 2090-APA-PRINTER and a character
image have been specified.
- DEVICE-TYPE=LOCAL or =EMULATED and a user ID have been specified.
- DEVICE-TYPE=9021 or =9022 or =9022-200 or =9025 or =9000-PCL or =DJET
or =LP65 or 2050-APA and FORM-FEED=LISTING have been specified.
- DEVICE-TYPE=2090-APA and FORM-FEED=SINGLE-SHEET have been specified.
- DEVICE-TYPE=9003 and ACCESS=HARDCOPY and FORM-FEED=SINGLE-SHEET
have been specified.
- DEVICE-TYPE=LP65 and DEFAULT-TRAY greater than 3.
- DEVICE-TYPE=LP65 or =2050-APA and DEFAULT-TRAY and OUTPUT-TRAY not
specified together.
- DEVICE-TYPE other than LP65 or 2050-APA and OUTPUT-TRAY not equal
to 0.
- DEVICE-TYPE=9645 and DISCONNECTION=NO have been specified.
- BUFFER-SIZE > 2048 has been specified for a 9025 Printer.
- DEVICE-TYPE=2050-APA-PRINTER or 2090-APA-PRINTER and BAND-ID
specified.
- A pool with the same name already exists.
- NOT-USABLE CHAR-SET-POSITION is specified in the corresponding
*STD record.
- The REPEAT-MESSAGE type is not compatible with the REPEAT-MESSAGE
operand.
SRV0518
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0518 VALUE '(&00)' OF '(&01)' OPERAND REPLACED BY '(&02)' IN '(&03)' COMMAND OR STATEMENT
Meaning
Certain information is classified and may not be given to not privileged
users. The request is modified so that only information for which the
user is authorized will be returned.
(&00): value originally entered (explicitly or by default)
(&01): operand name concerned
(&02): new value substituted for the original one
(&03): command or statement name.
SRV0519
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0519 NO MODIFICATION/REMOVE OF '(&00)' DEVICE/POOL ALLOWED FOR THE MOMENT. COMMAND OR STATEMENT NOT PROCESSED.
Meaning
A device/POOL for which waiting or kept jobs are still present
may not be modified/removed. Wait completion of those jobs and try
again the command or statement.
SRV0520
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0520 INTERNAL ERROR '(&01)' IN '(&00)' STATEMENT
Meaning
(&01): Internal error code x'00ZZXXYY':
YY = X'08' : SPM parameter error with the following associated XX:
XX = X'01' : parameter list allocation error
x'02' : record type field allocation error
x'03' : buffer allocation error
x'11' : invalid action
x'12' : invalid type
x'13' : invalid sub-action code
x'15' : invalid record type
x'16' : criterion list too large
x'30' : request too large
x'40' : privilege error
x'80' : invalid context
YY = X'09': SPM criterion list error with following associated XX:
XX = X'01' : allocation error
x'11' : invalid criterion identifier
x'12' : invalid type
x'13' : invalid form
x'14' : invalid length
x'21' : type not allowed
x'22' : form not allowed
x'31' : invalid list
x'32' : invalid wildcard
x'33' : invalid range
x'80' : duplicate criterion
x'80' : duplicate criterion
ZZ = debugging use only.
SRV0521
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0521 INTERNAL ERROR '(&01)' IN '(&00)' COMMAND. ABNORMAL TASK TERMINATION INITIATED
Meaning
(&01): Internal error code X'0000XXYY':
YY: 08, SPM parameter error
XX: 01, parameter list allocation error
02, record type field allocation error
03, buffer allocation error
11, invalid action
12, invalid type
13, invalid sub-action code
15, invalid record type
16, criteria list too long
30, request too complex
40, privilege error
80, invalid context
YY: 09, SPM criteria list error
XX: 01, allocation error
11, invalid criterion identifier
12, invalid type
13, invalid form
14, invalid length
21, type not allowed
22, form not allowed
31, invalid list
32, invalid wildcard
33, invalid range
80, duplicate criterion.
SRV0522
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0522 SPECIFIED LOWER LIMIT VALUE EXCEEDS THE UPPER LIMIT. '(&00)' COMMAND OR STATEMENT REJECTED
Meaning
The lower value specified in the range criterion exceeds the upper value.
Response
Correct the values and retry the command or statement.
SRV0523
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0523 INVALID '(&00)' VALUE. '(&01)' COMMAND OR STATEMENT REJECTED
SRV0524
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0524 OUTPUT MODE 'HEXA-AND-CHAR' ONLY ALLOWED WITH 'ORIGIN=MIXED-DISPLAY'. STATEMENT REJECTED
SRV0525
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0525 INVALID VALUE FOR '(&00)' OPERAND IN '(&01)' STATEMENT. STATEMENT NOT PROCESSED
Meaning
An error has been detected in the internal table of the
SPOOL.PARAMETERS file.
SRV0526
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0526 WARNING: 'TWO-UP=MODE-3' NO LONGER SUPPORTED. FORM '(&00)' DELETED
Meaning
Form (&00) uses the not supported TWO-UP=MODE-3 option. The form record
is deleted from the SPOOL.PARAMETERS file.
(&00): form name.
SRV0527
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0527 WARNING: NONSUPPORTED VALUE OF R-P-M HAS BEEN REPLACED BY 4096 IN '(&00)' RECORD
Meaning
A raster pattern memory value which is no longer supported was given in an
//ADD-SPOOL-DEVICE or //MODIFY-SPOOL-DEVICE statement or in a GEN record.
This invalid value has been changed into the lowest possible one (4096).
(&00): device name or GLOBAL.
SRV0528
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0528 DMS ERROR WHILE CREATING OR UPDATING THE SPOOL PARAMETER FILE. ONLY TABLES PROCESSED
Meaning
A DMS error has occurred which prevents the SPOOL parameter file update.
The SPOOL session may continue, but any further attempt to update the
SPOOL parameters via a command will only modify the table, except if the
file becomes accessible again. The update is valid only for the current
session.
Response
The file will be repaired at the next SPOOL start-up if possible.
All modifications made from now on until the end of the session must
be re-entered after the next start-up.
SRV0529
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0529 VALUE OF '(&00)' OPERAND IS NO MORE SUPPORTED. '(&01)' RECORD NOT PROCESSED. PROCESSING CONTINUES
Meaning
- 'YES' value for ND-PRINTER operand in GEN record.
- a non zero value for RBP-STATION-LIMIT operand in GEN record.
(&00) : operand name.
(&01) : record type.
SRV0530
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0530 THE DEVICE TYPE '(&00)' IS NO MORE SUPPORTED. PROCESSING CONTINUES
Meaning
The corresponding form records are removed from the processed
SPOOL.PARAMETERS file.
(&00) : device type.
SRV0531
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0531 THE DEVICE TYPE '(&00)' IS NO MORE SUPPORTED. '(&01)' RECORD NOT PROCESSED. PROCESSING CONTINUES
Meaning
The corresponding form and/or device records are not copied or
merged in the processed SPOOL.PARAMETERS file.
(&00) : device type.
(&01) : record type.
SRV0532
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV0532 DEVICE TO BE MODIFIED IS BEING USED IN ONE OR MORE POOLS. COMMAND REJECTED
Meaning
The type of a device included in a pool may not be modified by
command in order to prevent inconsistencies.
Response
Use SPSERVE to modify the device type.
SRV0533
Destination: CONSOLE Routing code: S Weight: 99
Warranty : NO
SRV0533 THE SPOOL PARAMETER FILE '(&00)' IS EXCATED. THE SPOOL PARAMETERS START-UP IS ABORTED
Meaning
(&00) : SPOOL parameter file name
The file &00 needed for the SPOOL parameters
start-up is located on an excated disk.
The SPOOL sub-system start-up is aborted.
Response
Give /IMPORT-PUBLIC-VOLUME-SET command and retry
SRV0534
Destination: CONSOLE Routing code: S Weight: 99
Warranty : NO
SRV0534 SPOOL PARAMETER FILE MIGRATION FOR FILE '(&00)' STARTED
Meaning
(&00) : SPOOL parameter file name
An upgrade of spool objects contained in file (&00) is
started
SRV0535
Destination: CONSOLE Routing code: S Weight: 99
Warranty : NO
SRV0535 SPOOL PARAMETER FILE MIGRATION FOR FILE '(&00)' COMPLETED
Meaning
(&00) : SPOOL parameter file name
An upgrade of spool objects contained in file (&00) is
completed
SRV0536
Destination: CONSOLE Routing code: S Weight: 99
Warranty : NO
SRV0536 '(&00)' ERROR '(&01)' ON SPOOL PARAMETER FILE '(&02)'. PROCESSING CONTINUES
Meaning
(&00) : error type.
(&01) : DMS error code.
(&02) : SPOOL parameter file name.
For more detailed information, enter /HELP-MSG
in system mode or see BS2000 manual 'System Messaged'
SRV0537
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SRV0537 Illegal value for operand '(&00)' in statement '(&01)'.STATEMENT REJECTED
Meaning
'(&00)' name of the concerned operand
'(&01)' concerned statement
- The device specified in DEVICE-NAME operand must exist in
the spool PARAMETERS file.
- The device specified in DEVICE-NAME operand must support the
format specified in OUTPUT-FORMAT-NAME operand of the statement
SRV0538
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SRV0538 Device to be removed is being used by one or several filters. COMMAND REJECTED
SRV0540
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SRV0540 No filter or none of the specified filters exists. COMMAND OR STATEMENT REJECTED
Meaning
The SPOOL parameters filter table does not contain
any information about the specified filter(s).
SRV0541
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SRV0541 Inconsistency between the device definition and a filter definition
Meaning
The device to be modified is being used by one or several filters
To keep consistency between this device and the filter, the supported
format names of the device must contain at least the output
format name of the filter that uses the device.
SRV0542
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SRV0542 Several records comply with the selection criterion. Do you really want to remove these records ?(Yes or No)
SRV0543
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SRV0543 Statement aborted.
SRV0544
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SRV0544 No form complies with the selection criterion .
SRV0545
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SRV0545 The function is not supported
Meaning
The function is not supported in dynamic mode with the loaded
SPOOL version.
SRV0546
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SRV0546 The mixing of idom printers and local printers in a local pool is not allowed. Thus the following printers '(&00)' are not included in the pool
SRV0547
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SRV0547 The limit of administrator userids number is reached.
SRV0548
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SRV0548 The administrator userid(s) '(&00)' already exist(s).Processing continues.
SRV0549
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SRV0549 The administrator userid(s) '(&00)' to remove does not exist. Processing continues.
SRV0550
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SRV0550 Form '(&01)' with device-type '(&00)' does not exist. Statement continues
Meaning
(&00) : device-type
(&01) : form name
Concerned statement: //MODIFY-SPOOL-FORM
//REMOVE-SPOOL-FORM
SRV3201
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3201 WARNING
SRV3202
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3202 WARNING: EDITED OBJECT DOES NOT EXIST
Meaning
The corresponding '//ADD' statement will create it.
SRV3401
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3401 STATEMENT NOT ALLOWED IN CURRENT MODE
Meaning
The right mode can be set by using the '//OPEN-PARAMETER-FILE' statement.
SRV3402
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3402 UNKNOWN SPSERVE STATEMENT
Meaning
The statement is not recognized by SPSERVE.
This can be due to a discrepancy between the versions of the SPSERVE
program and of its syntax file.
SRV3403
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3403 INVALID OBJECT NAME
Meaning
The specified object name is not valid for this statement.
SRV3404
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3404 OBJECT NAME ALREADY USED
Meaning
The specified object name is already used by an object of another type.
SRV3405
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3405 INVALID REFERENCED HOST
Meaning
The referenced object does not exist or is not a valid host.
SRV3406
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3406 INVALID REFERENCED SERVER
Meaning
The referenced object does not exist or is not a valid server.
SRV3407
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3407 INVALID REFERENCED PRINTER
Meaning
The referenced object does not exist or is not a valid distributed
printer.
SRV3408
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3408 INVALID REFERENCED PRINTER POOL
Meaning
The referenced object does not exist or is not a valid distributed pool.
SRV3409
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3409 INVALID REFERENCED ACCESS CONTROL
Meaning
The referenced object does not exist or is not a valid access control.
SRV3410
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3410 OBJECT CURRENTLY REFERENCED BY ANOTHER ONE
Meaning
An other object of the configuration references the specified one.
SRV3411
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3411 OBJECT ALREADY EXISTS
Meaning
The specified object already exist in the configuration.
SRV3412
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3412 OBJECT DOES NOT EXIST
Meaning
The specified object does not exist in the configuration.
SRV3413
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3413 INVALID RECORD FORMAT
Meaning
The layout of the record built by SPSERVE does not match its
specification.
SRV3414
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3414 OBJECT CURRENTLY REFERENCED BY A SERVER OBJECT
Meaning
The specified object name is referenced by a server.
SRV3415
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3415 OBJECT CURRENTLY REFERENCED BY A HOST OBJECT
Meaning
The specified object name is referenced by a host.
SRV3500
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3500 OBJECT CURRENTLY REFERENCED BY A PRINTER OBJECT
Meaning
The specified object name is referenced by a printer.
SRV3501
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3501 OBJECT CURRENTLY REFERENCED BY A PRINTER POOL OBJECT
Meaning
The specified object name is referenced by a printer pool.
SRV3502
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3502 OBJECT CURRENTLY REFERENCED BY A REMOTE CLUSTER OBJECT
Meaning
The specified object name is referenced by a remote cluster.
SRV3503
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3503 INVALID CLUSTER DEFINITION OR MODIFICATION
Meaning
The network address of a remote cluster can not be defined as a local
cluster host.
Only one SINIX cluster may be defined with the same host name and gateway
name.
SRV3504
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3504 THE GIVEN HOST NAME IS ALREADY USED AS NETWORK ADDRESS OF A REMOTE CLUSTER
Meaning
The local cluster host can not be defined as a network address of a remote
cluster.
SRV3505
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3505 A SERVER IS ALREADY REFERENCED BY THE GIVEN HOST
Meaning
Only one server may be attached to a given host.
SRV3506
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3506 THE GIVEN PRINTER NAME IS ALREADY USED AS PRINTER POOL NAME
Meaning
Printer and printer pool names must be different.
SRV3507
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3507 THE GIVEN PRINTER POOL NAME IS ALREADY USED AS PRINTER NAME
Meaning
Printer and printer pool names must be different.
SRV3508
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SRV3508 No remove of dprint printer pool is allowed for the moment. The statement is rejected.
Meaning
A DPRINT printer pool for which waiting or kept jobs
are still present may not be removed.
SRV3601
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3601 ERROR
SRV3602
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3602 PRIVILEGE TOO LOW
Meaning
The privilege of the task do not allow it to execute this statement.
SRV3603
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3603 OBJECT CURRENTLY ACTIVE
Meaning
The specified object must be deactivated before processing it.
SRV3604
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3604 CONFIGURATION CURRENTLY LOCKED
Meaning
The configuration is currently locked by another processing.
SRV3605
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3605 ICRM ACCESS ERROR
Meaning
The selected ICRM is currently not accessible.
SRV3615
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3615 FUNCTION NOT SUPPORTED
Meaning
The SPOOL&PRINT subsystems are not able to satisfy the request of SPSERVE.
SRV3700
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3700 DPRINTCM SUBSYSTEM NOT AVAILABLE
Meaning
The DPRINT subsystem is currently not accessible.
SRV3801
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3801 SYSTEM ERROR
Meaning
An error occurred during a general purpose system call.
SRV3802
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3802 DPRINT ERROR
Meaning
An internal DPRINT error occurred.
SRV3803
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3803 MEMORY REQUEST ERROR
Meaning
An error occurred during a user memory request.
SRV3804
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3804 MEMORY RELEASE ERROR
Meaning
An error occurred during a user memory release.
SRV3901
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV3901 DPRINT SHOW ERROR
Meaning
An error occurred during the DPRINT processing of the statement.
SRV4001
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV4001 INTERNAL ERROR: TRANSFER AREA DOES NOT EXIST
SRV4002
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV4002 INTERNAL ERROR: SYNTAX FILE CONVENTION ERROR
SRV4201
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV4201 INTERNAL ERROR: UNEXPECTED VALUE ENCOUNTERED
SRV4202
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV4202 INTERNAL ERROR: UNEXPECTED DPRINT RETURN CODE
SRV4203
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV4203 INTERNAL ERROR: INTERNAL AREA SIZE ERROR
SRV4204
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV4204 INTERNAL ERROR: DPRINT PARAMETER LIST LAYOUT ERROR
SRV4205
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SRV4205 INTERNAL ERROR: DPRINT CRITERION LIST LAYOUT ERROR