Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SPA0001 '(&00)' ERROR CODE '(&01)'. SPOOLOUT REQUEST ABORTED
Meaning
An error occurred during spoolout request processing.
(&00): EAM : EAM error
REQ : user request error
PUTQ: put queue error
REQM: request memory error
DMS : DMS error
CAT : catalog error.
(&01): specific error code belonging to (&00)
04: queue routine error
0C: catalog error
10: EAM processing error
18: password validation failure
1C: $REQM error (LOGOFF only)
20: $RELM error (LOGOFF only)
24: parameter validation failure
28: cannot erase unowned file
2C: non-shareable file
30: record size and block size are zero
34: creation date, expiration date or last page used is 0
38: file not SAM, PAM or ISAM
3C: invalid parameter address
40: EAM OMF (object module file) not existing
44: EAM file contains no data
48: invalid ERASE option (FGG (file generation group) files)
54: RFA mode not supported in SPOOL
58: DEVIN for a not SAM tape file
60: tape without STD labels
64: system file is not PRIMARY
68: system file does not exist
6C: FLUSH/CLOSE error on system file
70: File currently in use and therefore locked.
If a DMS error code is output, for more detailed information about this
error code enter /HELP-MSG in system mode or see the BS2000 manual
'System Messages'.
SPA0002
Destination: USER-TASK, CONSOLE Routing code: S Weight: 99
Warranty : NO
SPA0002 $VALID ERROR FOR SPOOL REQUEST P/L
Meaning
The parameter list address is not correct.
SPA0003
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SPA0003 SPOOL NOT LOADED OR NOT READY. COMMAND TERMINATED
Response
Try again later or contact the system administrator.
SPA0004
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SPA0004 SYSTEM ERROR. COMMAND REJECTED
Meaning
A system error has occurred during the command processing.
Response
Contact the system administrator.
SPA0005
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SPA0005 INVALID PARAMETER LIST ALIGNEMENT. COMMAND REJECTED
Meaning
The address of the $SSVRQ parameter list is not aligned.
Response
Correct the address and try again the command.
SPA0006
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SPA0006 ERROR CODE '(&00)' IN TSN REASSIGNMENT INTERFACE. STARTUP ABORTED. IN SYSTEM MODE: /HELP-MSG DMS(&00).
Meaning
An error (&00) has occurred during processing of the TSN reassignment.
For more detailed information about the DMS error code enter /HELP-MSG in
system mode or see the BS2000 manual 'System Messages'.
SPA0007
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SPA0007 OLD EQUISAMQ FILE CANNOT BE PROCESSED DUE TO DMS ERROR '(&00)'. STARTUP CONTINUED AS COLD START. IN SYSTEM MODE: /HELP-MSG DMS(&00)
Meaning
During the EQS startup, the queue file cannot be processed due
to DMS error (&00).
For more detailed information about the DMS error code enter /HELP-MSG in
system mode or see the BS2000 manual 'System Messages'.
SPA0008
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SPA0008 $DCALOCK ERROR CODE '(&00)' FOR FILE '(&01)'. PROCESSING CONTINUED
Meaning
The attempt to restore the lock on the print file (&01) resulted in an
error.
For more detailed information about the $DCALOCK error code see the
BS2000 manual 'System Messages'.
SPA0009
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SPA0009 WARNING: BLOCKS DESTROYED OF OLD EQUISAMQ FILE. PROCESSING CONTINUED WITH RECORD ALREADY PROCESSED
Meaning
A problem occurs during the verify of the EQUISAMQ file.
The records already processed by the $VRIF macro are kept and the
remaining
records of the file are lost.
SPA0010
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SPA0010 DMS ERROR '(&00)' DURING PROCESSING 'FILE' OR 'OPEN' MACRO. STARTUP ABORTED. IN SYSTEM MODE: /HELP-MSG DMS(&00)
Meaning
For more detailed information about the DMS error code enter /HELP-MSG in
system mode or see the BS2000 manual 'System Messages'.
SPA0011
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SPA0011 EQUISAMQ ACCESS NOT POSSIBLE. 'IMCAT' OR 'EXCAT' PROCESSING FOR SPOOL JOBS ABORTED. PROCESSING CONTINUED
Meaning
The EQUISAMQ file is locked by a further /IMCAT or /EXCAT command or by
the SPOOL startup. The state of the SPOOL jobs for the processed PVS is
not changed in the EQUISAMQ file.
SPA0012
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SPA0012 REQUEST MEMORY ERROR. 'IMCAT' OR 'EXCAT' PROCESSING FOR SPOOL JOBS ABORTED. PROCESSING CONTINUED
Meaning
An internal problem of request memory occurs during the processing. The
state of the SPOOL jobs for the processed PVS is not changed in the
EQUISAMQ file.
SPA0013
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SPA0013 DMS ERROR '(&00)' ON EQUISAMQ FILE. IN SYSTEM MODE: /HELP-MSG DMS(&00)
Meaning
(&00): DMS error code.
For more detailed information about the DMS error code enter /HELP-MSG in
system mode or see the BS2000 manual 'System Messages'.
Response
Take measure corresponding the DMS error code.
If required, take a system dump and create a new EQUISAMQ file by making
a cold start.
SPA0015
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SPA0015 Invalid specification in the string operand given during the start-up of SPOOLSYS subsystem. SPOOLSYS subsystem start-up aborted
SPA0016
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SPA0016 Internal error during the anchor processing of the SPOOLSYS XVT. SPOOLSYS subsystem start-up aborted
SPA0017
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SPA0017 Invalid specification in the '(&00)' parameter file. SPOOLSYS subsystem start-up aborted
SPA0018
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SPA0018 '(&00)' subsystem not loaded or not ready. Command terminated
Meaning
(&00): subsystem name
Response
Contact the System Administrator and retry later.
SPA0100
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SPA0100 DMS error '(&00)' with interface '(&01)' for file '(&02)'. Further information: /HELP-MSG DMS(&00)
Meaning
(&00) : DMS error code
(&01) : DMS interface name
(&02) : filename
SPA0101
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SPA0101 System error. Command abnormally terminated
Meaning
An error occurred during the call of a system interface.
More information can be found in SERSLOG file with RECTYPE=SPA0000.
SPA0102
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SPA0102 Command abnormally terminated
Meaning
The command has been abnormally terminated.
More information can be found in the previous message(s).
SPA0103
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SPA0103 Command currently processed by another task
Meaning
The command may not be processed simultaneously by several tasks.
Response
Retry command later.
SPA0104
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SPA0104 FROM-FILE and TO-FILE operands may not be equivalent
Meaning
The FROM-FILE and TO-FILE operands may not refer to the same file.
Response
Correct command and retry.
SPA0105
Destination: CONSOLE Routing code: S Weight: 99
Warranty : NO
SPA0105 Original tsn '(&00)' of print job has been changed into tsn '(&01)'
Meaning
The print job TSN has been changed because this tsn already exists
on the system where the print job has been moved.
(&00) : original print job tsn
(&01) : new print job tsn
SPA0106
Destination: CONSOLE Routing code: S Weight: 99
Warranty : NO
SPA0106 SPOOL task '(&00)' error '(&01)' from '(&02)' interface for tsn '(&03)'. Processing aborted
Meaning
An error (&01) occurred on (&00) task, when processing (&02) interface
on print job (&03).
Response
Contact the Print-Service Administrator.
SPA0107
Destination: CONSOLE Routing code: S Weight: 99
Warranty : NO
SPA0107 Internal error '(&00)' from module '(&01)'. Processing aborted
Meaning
An internal error (&00) occurred in (&01) module.
This message is sent for diagnosis purposes.
Response
Contact the Print-Service Administrator.
SPA0108
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SPA0108 SPOOL subsystem currently being loaded or unloaded. Retry command later
Meaning
The system standard EQUISAMQ file is to be processed by the current
command; however, the SPOOL subsystem, which also uses this file
is currently in an intermediate status
Response
Wait until SPOOL is completely loaded or unloaded
and try the command again.
SPA0109
Destination: CONSOLE Routing code: S Weight: 99
Warranty : NO
SPA0109 Class '(&00)' memory request error. Processing aborted
Meaning
(&00) : memory class
Response
Contact the System Administrator.
SPA0110
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SPA0110 /MOVE-PRINT-JOBS command currently processed. Retry command later
Meaning
The system standard EQUISAMQ file is to be processed by SPOOL subsystem;
however, a /MOVE-PRINT-JOBS command currently uses this file.
Response
Wait until the command is completely processed
and try again to start/resume or stop/hold SPOOL subsystem.
SPA0111
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SPA0111 Command successfully processed
SPA0112
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SPA0112 No print job corresponds to the specified operand values. Command not processed
SPA0113
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SPA0113 Command partially processed
SPA0114
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SPA0114 '(&00)' print job(s) processed. Command terminated
Meaning
(&00) : number of print jobs corresponding to the selection criteria
that have been moved.
SPA0115
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SPA0115 '(&00)' print job(s) not processed due to '(&01)' error
Meaning
(&00): number of print jobs corresponding to the selection criteria
that have not been moved.
(&01): error cause:
- 'file lock' means that an error occurred when trying to lock
a file related to one of the selected print jobs
(a.o. when the file is located on a non accessible pubset,...)
- 'sysdprnt catid' means that the current default SYSDPRNT catid
does not correspond to the one associated with the print job
to move
- 'SPOOL status' means that SPOOL subsystem was loaded
when tsn collision occurred during processing of distributed
print jobs
'WRONG HOST' means that the target host does not fit for the
print job: either a client copy of a print job is moved onto its
server host or a server copy of a print job is moved onto
its client host.
SPA0116
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SPA0116 '(&00)' subsystem ready: /MOVE-PRINT-JOBS command may not be processed. Retry command later
Meaning
(&00): subsystem name
A /MOVE-PRINT-JOBS command that processes distributed print jobs
is not allowed while (&00) subsystem is present.
Response
Unload (&00) subsystem, wait until it is not ready
and try the command again.
SPA0117
Destination: CONSOLE Routing code: S Weight: 99
Warranty : NO
SPA0117 Print job with tsn '(&00)' suspended in '(&01)' EQUISAMQ file
Meaning
(&00): print job tsn
(&01): filename of the EQUISAMQ file specified as 'TO-FILE' operand
The current print job has been temporarily suspended,
as a currently being moved print job with the same tsn has
a higher priority.
Reason: the default SYSDPRNT catid has been temporarily switched,
so that the print job could not be processed.
Response
Switch again the default SYSDPRNT catid,
use the /MOVE-PRINT-JOBS command with FROM-FILE= to move print jobs
- really or not- and the suspended print jobs will automatically
be schedulable again.
SPA0118
Destination: CONSOLE Routing code: S Weight: 99
Warranty : NO
SPA0118 Print job with tsn '(&00)' resumed in '(&01)' EQUISAMQ file
Meaning
(&00): print job tsn
(&01): filename of the EQUISAMQ file specified as 'FROM-FILE' operand
The current print job had been previously suspended with SPA0117 message.
As the default SYSDPRNT catid has been switched again,
the print job may now be processed as usual.
SPA0119
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SPA0119 '(&00)' print job(s) suspended in '(&01)' EQUISAMQ file
Meaning
(&00): number of print jobs that have been suspended
(&01): filename of the EQUISAMQ file specified as 'TO-FILE' operand
A more precise information about the suspended print jobs
has been sent to console - SPA0117 message.
SPA0120
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SPA0120 '(&00)' print job(s) resumed in '(&01)' EQUISAMQ file
Meaning
(&00): number of print jobs that have been resumed
(&01): filename of the EQUISAMQ file specified as 'FROM-FILE' operand
A more precise information about the resumed print jobs
has been sent to console - SPA0118 message.
SPA0121
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SPA0121 /MOVE-PRINT-JOBS command currently processed. Retry command later
Meaning
A /MOVE-PRINT-JOBS command currently uses the system standard
EQUISAMQ file in order to process distributed print jobs.
SPOOL subsystem may not be ready during this processing.
Response
Wait until the command is completely processed
and try again to start/resume SPOOL subsystem.
SPA0122
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SPA0122 /MOVE-PRINT-JOBS command currently processed. '(&00)' subsystem may not be loaded. Retry command later
Meaning
(&00): subsystem name
A /MOVE-PRINT-JOBS command currently uses the system standard
EQUISAMQ file in order to process distributed print jobs.
(&00) subsystem may not be ready during this processing.
Response
Wait until the command is completely processed
and try again to start/resume the subsystem.