HAL

HAL0001

Destination: CONSOLE     (message is issued without MIP, in English only)

Warranty   : NO

HAL0001   MDEBUG ACTIVE

Meaning

The master debugger mdebug has been started.

HAL0002

Destination: CONSOLE     (message is issued without MIP, in English only)

Warranty   : NO

HAL0002   MDEBUG INACTIVE

Meaning

The master debugger mdebug has been stopped.

HAL0111

Destination: CONSOLE     (message is issued without MIP, in English only)

Warranty   : NO

HAL0111   ADMIN RESET GPXX SSSSSSSSSSSSSSSS PPPPPPPPPPPPPPPP

Meaning

VM2000 has stopped and reset the processor concerned due to a VM2000 command.

HAL0112

Destination: CONSOLE     (message is issued without MIP, in English only)

Warranty   : NO

HAL0112   ADMIN STOP GPXX SSSSSSSSSSSSSSSS PPPPPPPPPPPPPPPP

Meaning

VM2000 has stopped the processor concerned due to a VM2000 command.

HAL0140

Destination: CONSOLE     (message is issued without MIP, in English only)

Warranty   : NO

HAL0140   HAL ABORT GPXX SSSSSSSSSSSSSSSS PPPPPPPPPPPPPPPP

Meaning

The HAL on this processor has detected an inconsistency and has terminated the
processing of BS2000 instructions on all processors.

Response

In the SEM execute the action “Generate new diagnostic data" under Hardware -> Server -> - Service - Diagnostics and save the data by downloading it to your administration PC.
Please notify the Customer Support.

HAL0141

Destination: CONSOLE     (message is issued without MIP, in English only)

Warranty   : NO

HAL0141   HAL ABORT GPXX SSSSSSSSSSSSSSSS PPPPPPPPPPPPPPPP OTHER GP

Meaning

The HAL on another processor has detected an inconsistency and has terminated the
processing of BS2000 instructions on all processors.
This message is a continuation message of HAL0140.

HAL0211

Destination: CONSOLE     (message is issued without MIP, in English only)

Warranty   : NO

HAL0211   MDEBUG STOP GPXX SSSSSSSSSSSSSSSS PPPPPPPPPPPPPPPP

Meaning

The master debugging interface has been used by either mdebug or RMAassist to halt the
processing of BS2000 instructions. This may happen as a normal part of IPL processing or
if mdebug is being used to examine the system.

HAL0212

Destination: CONSOLE     (message is issued without MIP, in English only)

Warranty   : NO

HAL0212   MDEBUG STOP GPXX SSSSSSSSSSSSSSSS PPPPPPPPPPPPPPPP BREAK-POINT

Meaning

A break point set by mdebug has been executed by the given processor. The processing of
BS2000 instructions has been halted.

HAL0213

Destination: CONSOLE     (message is issued without MIP, in English only)

Warranty   : NO

HAL0213   MDEBUG STOP GPXX SSSSSSSSSSSSSSSS PPPPPPPPPPPPPPPP DATA TRAP

Meaning

The given processor has executed an instruction that has modified a virtual memory
address that is being monitored for modification via mdebug. The processing of BS2000
instructions has been halted.

HAL0214

Destination: CONSOLE     (message is issued without MIP, in English only)

Warranty   : NO

HAL0214   MDEBUG STOP GPXX SSSSSSSSSSSSSSSS PPPPPPPPPPPPPPPP SAVE-STATE

Meaning

The master debugging interface has been used by either mdebug or RMAassist to halt the
processing of BS2000 instructions in preparation for a new IPL. This always happens as a
normal part of IPL processing.

HAL0215

Destination: CONSOLE     (message is issued without MIP, in English only)

Warranty   : NO

HAL0215   MDEBUG SPIN GPXX SSSSSSSSSSSSSSSS PPPPPPPPPPPPPPPP FW-STOP

Meaning

The relevant processor has interrupted the execution of BS2000 instructions due to a breakpoint in HAL set by mdebug.

HAL0221

Destination: CONSOLE     (message is issued without MIP, in English only)

Warranty   : NO

HAL0221   MDEBUG START GPXX SSSSSSSSSSSSSSSS PPPPPPPPPPPPPPPP

Meaning

The master debugging interface has been used by either mdebug or RMAassist to start the
processing of BS2000 instructions. This is not a normal part of IPL processing but the result
of administrator intervention with mdebug or RMAssist.

HAL0231

Destination: CONSOLE     (message is issued without MIP, in English only)

Warranty   : NO

HAL0231   MDEBUG RESET DATABP GPXX

Meaning

The monitoring for modification of a virtual memory address has been stopped on the
processor concerned.

HAL0241

Destination: CONSOLE     (message is issued without MIP, in English only)

Warranty   : NO

HAL0241   MDEBUG SET DATABP GPXX VVVVVVVVVVVVVVVV

Meaning

The monitoring for modification of the given virtual memory address has been started on
the processor concerned.

HAL0311

Destination: CONSOLE     (message is issued without MIP, in English only)

Warranty   : NO

HAL0311   BS2000 STOP GPXX SSSSSSSSSSSSSSSS PPPPPPPPPPPPPPPP DISABLED-WAIT

Meaning

A new PSW has been loaded by the given processor in which the wait bit is set and no
interrupts are enabled. As a result, the processing of BS2000 instructions has been halted.
This may occur as part of a normal system shutdown or may be due to a system crash -
SETS.

Response

If the BS2000 system is no longer running and was not terminated intentionally, please perform a SLED to back up the diagnostic data.

HAL0312

Destination: CONSOLE     (message is issued without MIP, in English only)

Warranty   : NO

HAL0312   BS2000 STOP GPXX SSSSSSSSSSSSSSSS PPPPPPPPPPPPPPPP SIGP

Meaning

BS2000 stopped the processor concerned using an SIGP instruction. This is a normal
during BS2000 system shutdown or when a CPU is detached, but also occurs in
conjunction with a system crash or SETS.

Response

If the BS2000 system is no longer running and was not terminated intentionally, please
perform a SLED to back up the diagnostic data.

HAL0313

Destination: CONSOLE     (message is issued without MIP, in English only)

Warranty   : NO

HAL0313   BS2000 STOP GPXX SSSSSSSSSSSSSSSS PPPPPPPPPPPPPPPP SIGP RESET

Meaning

BS2000 has reset the processor concerned using an SIGP instruction.

HAL0314

Destination: CONSOLE     (message is issued without MIP, in English only)

Warranty   : NO

HAL0314   BS2000 STOP GPXX SSSSSSSSSSSSSSSS PPPPPPPPPPPPPPPP SIGP STORE-STATUS

Meaning

BS2000 used an SIGP instruction to request that diagnostic data about the current state of
the processor concerned be saved.

HAL0315

Destination: CONSOLE     (message is issued without MIP, in English only)

Warranty   : NO

HAL0315   BS2000 STOP GPXX SSSSSSSSSSSSSSSS PPPPPPPPPPPPPPPP START DUMP

Meaning

The processor concerned has been stopped because a dump IPL has been started by
BS2000 (Crash Restart).

HAL0316

Destination: CONSOLE     (message is issued without MIP, in English only)

Warranty   : NO

HAL0316   BS2000 STOP GPXX SSSSSSSSSSSSSSSS PPPPPPPPPPPPPPPP START IPL

Meaning

The processor concerned has been stopped because an IPL has been started by BS2000
(Shutdown Restart).

HAL0321

Destination: CONSOLE     (message is issued without MIP, in English only)

Warranty   : NO

HAL0321   BS2000 START GPXX SSSSSSSSSSSSSSSS PPPPPPPPPPPPPPPP SIGP

Meaning

BS2000 has started the processor concerned with an SIGP instruction.

HAL0322

Destination: CONSOLE     (message is issued without MIP, in English only)

Warranty   : NO

HAL0322   BS2000 START GPXX SSSSSSSSSSSSSSSS PPPPPPPPPPPPPPPP IPL-RESTART

Meaning

The master debugging interface has been used by either mdebug or RMAassist to start the
processing of BS2000 instructions directly after a new IPL boot block has been loaded. This
is the last step in normal IPL processing.

HAL0440

Destination: CONSOLE     (message is issued without MIP, in English only)

Warranty   : NO

HAL0440   IOD ABORT GPXX SSSSSSSSSSSSSSSS PPPPPPPPPPPPPPPP IOD-ABEND

Meaning

An error has been recognized by the input/output driver and processing has been
terminated. In the case of a BS2000 restart and a DIPL into the running system, this
message is normal and can be ignored.

Response

Examine the proceeding messages on the BS2000 console for information as to the cause
of the problem.