Destination: USER-TASK Routing code: Weight:
Warranty : NO
SAECOPY Copyright (C) '(&00)' '(&01)' All Rights Reserved
SAELOAD
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SAELOAD Program '(&00)', Version '(&01)' of '(&02)' loaded from file '(&03)'
SAESTRT
Destination: USER-TASK Routing code: Weight:
Warranty : NO
SAESTRT Procedure '(&00)', Version '(&01)' of '(&02)' started from file '(&03)'
SAE5000
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5000 PROGRAM '(&00)' UNKNOWN IN SYNTAX FILE. STATEMENT NOT PROCESSED
Meaning
A name inconsistency has been detected between the program and
the syntax file.
Response
Activate the correct syntax file.
SAE5002
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5002 SDF RETURN CODE '(&00)'. STATEMENT NOT PROCESSED
Meaning
SDF returns an unexpected error code.
Response
Check the error with the aid of the "SDF-A" manual and contact
the system administrator.
SAE5004
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5004 SAT FILE EVALUATOR TERMINATED NORMALLY
SAE5005
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5005 SAT FILE EVALUATOR TERMINATED ABNORMALLY
Response
Check the program run or statement sequence for more information
about the error.
SAE5006
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5006 SYNTAX VALIDATION TERMINATED
Meaning
The syntax of the statement has been validated against the syntax
file.
Response
Previous messages may indicate a syntax error.
SAE5007
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5007 USER NOT AUTHORIZED TO CALL SAT FILE EVALUATOR
Meaning
Use of this program is restricted.
SAE5008
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5008 INCONSISTENCY BETWEEN SAT FILE EVALUATOR AND ITS SYNTAX FILE
Meaning
Possible reasons:
- The contents of the syntax file does not correspond with the
contents expected from the evaluation program.
- The version of the syntax file does not correspond with the
version expected from the evaluation program.
- The contents and the version of the syntax file do not
correspond with those expected from the evaluation program.
Response
Contact the system administrator.
SAE5050
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5050 FILE '(&00)' IS NOT A VALID SAT ANALYSIS FILE. STATEMENT NOT PROCESSED
Meaning
Possible reasons:
- Because of inconsistency or incompleteness the headerinformation
can be concluded that the analysis-file is incorrect or is not
created by SATUT
- the specified file is a SAT-logging file, but it couldn't be
interpreted
Response
- Repeat with new analysis-file
- SAT-logging files have to be specified by *STD()
SAE5051
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5051 LIST OF FILES TOO LONG. STATEMENT NOT PROCESSED
Meaning
The list of file names corresponding to the given criterion contains
more than 25 files.
SAE5052
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5052 RECORDS IN FILE '(&00)' AND FILE '(&01)' MAY BE DUPLICATED. STATEMENT PROCESSING TERMINATED ABNORMALLY
Meaning
File (&01) has been created with some of the records contained in
file (&00). If both files are used to produce a new
replacement-file, there is a risk that certain records in this new
file will be contained twice.
SAE5053
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5053 RELM ERROR. STATEMENT PROCESSING TERMINATED ABNORMALLY
Meaning
The program detected a RELM error during processing.
Response
Try again later or enter another evaluator statement.
SAE5054
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5054 REQUESTED FILE(S) CURRENTLY NOT AVAILABLE. RETRY LATER
Meaning
At least one of the files requested in the statement is already
being used.
Response
Try again later or enter another evaluator statement.
SAE5055
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5055 NO FILE CORRESPONDING TO GIVEN CRITERION
Meaning
The operands specified in the statement prevent files from being
selected.
SAE5057
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5057 INTERVAL OF DATE NOT ALLOWED. STATEMENT NOT PROCESSED
Meaning
The interval of date is not allowed. Completed with the century
the first date is higher than the second one.
SAE5058
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5058 DATE NOT ALLOWED. STATEMENT NOT PROCESSED
Meaning
The century is not correct for this year.
SAE5149
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5149 SPECIFIED VALUE '(&00)' OF OPERAND NOT ALLOWED
Response
Correct the operand value and try the statement again.
SAE5150
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5150 DUPLICATE OPERAND VALUE '(&00)'
Meaning
An operand value may only be specified once for a given operand.
Response
Correct the operand value and try the statement again.
SAE5151
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5151 OPERAND VALUE '(&00)' DOES NOT EXIST
Meaning
The specified operand value is a non-existent event.
Response
Correct the operand value and try the statement again.
SAE5152
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5152 '(&00)' NOT ALLOWED FOR NOT CONVERTED CONSLOG- OR SKP2-RECORDS. STATEMENT NOT PROCESSED
Meaning
(&00) in SATUT is only possible for records having the SAT record
format. The Conslog or SKP2 records, on which (&00) must be done,
have not been converted (thanks to statement SELECT-RECORDS
or START-SELECTION) into their corresponding SAT record format.
Response
AT first, select the records in a work file. Then, retry the (&00)
on this work file.
SAE5153
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5153 ERROR DURING SORT RUN. SORT ERROR CODE '(&00)'. STATEMENT NOT PROCESSED. FURTHER INFORMATION: /HELP-MSG SRT(&00)
Meaning
An error occurred when sorting the records.
Response
Analyze the SORT error code and recover the error.
SAE5250
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5250 NO HISTOGRAM IS FURNISHED WHEN OUTPUT MUST BE DONE ON SYSOUT. STATEMENT CONTINUES
Response
In order to obtain histogram, reenter statement with OUTPUT=SYSLST.
SAE5251
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5251 PASCAL ERROR '(&00)' ON FILE '(&01)'. STATEMENT NOT PROCESSED
Meaning
A PASCAL error has occurred during processing with file (&01).
For more detailed information about the PASCAL error code,
see the PASCAL-XT User's Guide manual.
Response
Reenter the statement after eliminating the error.
SAE5252
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5252 STATEMENT PROCESSING ABNORMALLY TERMINATED
Meaning
Due to an error in the statement processing, the statement has
been aborted.
Response
Reenter the statement after eliminating the error.
SAE5253
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5253 INTERNAL ERROR IN STATISTICS PROCESSING. STATEMENT NOT PROCESSED
Meaning
Internal data used for the SHOW-STATISTICS statement are too little.
Response
Contact the system administrator.
SAE5254
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5254 NO HISTOGRAMM IS FURNISHED BECAUSE OF INVALID EVENTS. STATEMENT CONTINUES
Meaning
As invalid events were encountered in one of the analyzed files,
the building of the histogram is not possible.
SAE5400
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5400 USER NOT AUTHORIZED TO CREATE 'REPLACEMENT-FILE'
SAE5401
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5401 INPUT FILES CANNOT BE ERASED WHEN AN 'ANALYSIS-FILE' IS TO BE CREATED
SAE5402
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5402 INPUT FILES AS 'ANALYSIS-FILES' CANNOT BE USED TO PRODUCE A 'REPLACEMENT-FILE'
SAE5403
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5403 FILE '(&00)' CANNOT BE ERASED
Meaning
An error occurred while erasing file (&00).
Response
Try to recover the error on the file (&00) with the help of the
specified DMS error code.
SAE5404
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5404 FUNCTION 'SAVE' WITHDRAWN BY USER
Meaning
The reduction file specified for creation by means of the statement
SAVE-SELECTED-RECORDS or the XML file specified for creation by means of
the statement SHOW-SELECTED-RECORDS is already cataloged.
Either the user has replied that the file is not to be overwritten
or the statement has been executed in batch mode.
SAE5405
Destination: USER-TASK Routing code: Weight: 98
Warranty : NO
SAE5405 OVERWRITE '(&00)' = '(&01)' ? REPLY (Y=YES; N=NO)
Meaning
The reduction file or XML file specified for creation is already
cataloged.
The user is asked whether or not the existing file is to be overwritten.
Response
Y: the file will be overwritten.
N: the SAVE function will not be carried out.
SAE5406
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5406 NEW '(&00)' = '(&01)' CREATED
Meaning
The creation of a reduction file with the statement SAVE-SELECTED-RECORDS
resp. the creation of a XML file with the statement SHOW-SELECTED-RECORDS
has been carried out without error.
(&00) : REDUCTION-FILE or XML-FILE
(&01) : Name of the reduction file resp. of the XML file
SAE5407
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5407 CREATION OF 'ANALYSIS-FILES' WITH SAME NAME AS ONE OF THE SATUT INPUT FILES IS NOT ALLOWED. STATEMENT NOT PROCESSED
Meaning
Inconsistencies can occur if an analysis-file is created,
with the name of one of the SATUT input files.
Response
Choose another name for the new analysis-file.
SAE5408
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5408 NO RECORD YET SELECTED IN WORK FILE '(&00)'. STATEMENT NOT PROCESSED
Meaning
Saving is only allowed for a work file of which contents
result from a selection.
SAE5409
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5409 FILE '(&00)' NOT ERASED. STATEMENT PROCESSING CONTINUES
Meaning
Conslog, SKP2 files and not-closed files are not erased by SATUT.
SAE5556
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5556 SPECIFIED UNIT INVALID. STATEMENT NOT PROCESSED
Meaning
For fields which are represened as a multiple of 512,
the specification of the following units is allowed:
- BYTES
- KB (kilobytes)
- MB (megabytes)
- GB (gigabytes)
If no unit has been specified, BYTES is taken as default value.
Response
Correct the unit and try the statement again.
SAE5557
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5557 SPECIFIED VALUE MUST BE A MULTIPLE OF 512. STATEMENT NOT PROCESSED
Meaning
For fields which are represented as a multiple of 512
the field value must be a multiple of 512
if no unit or the unit BYTES has been specified.
Response
Correct the field value and try the statement again.
SAE5558
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5558 SPECIFIED VALUE MUST NOT EXCEED MAXIMUM VALUE. STATEMENT NOT PROCESSED
Meaning
For fields which are represented as a multiple of 512
the field value must not exceed a certain maximum value
depending on the specified unit.
The following maximum values must be observed:
2**31 - 1, if the unit BYTES (or no unit) has been specified
2**30 - 1, if the unit KB has been specified
2**20 - 1, if the unit MB has been specified
2**10 - 1, if the unit GB has been specified
Response
Correct the field value and try the statement again.
SAE5559
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5559 INTERNAL ERROR DURING SYNTACTICAL ANALYSIS OF SELECTION CONDITION. STATEMENT NOT PROCESSED
Meaning
During the analysis of the unit for fields which are represented as
a multiple of 512 an internal error has occurred.
Response
Contact the system administrator.
SAE5571
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5571 SYNTAX ERROR IN SELECTION CONDITION
Meaning
The defined selection condition does not respect the syntax
described in the SECOS manual for the SATUT selection conditions.
Response
Correct selection condition try again.
SAE5572
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5572 INTERNAL ERROR IN SYNTACTICAL ANALYSIS OF SELECTION CONDITION. STATEMENT NOT PROCESSED
Meaning
Internal data used for the syntactical check of the selection
conditions are too small.
Response
Contact the system administrator.
SAE5573
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5573 TOO MANY ASTERISKS IN SELECTION CONDITION. STATEMENT NOT PROCESSED
Meaning
A pattern in the selection condition contains more asterisks
than allowed.
Response
Correct selection condition and try again.
SAE5574
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5574 TOO MANY NESTED BLOCK LISTS IN SELECTION CONDITION. STATEMENT NOT PROCESSED
Meaning
A pattern in the selection condition contains a too high number
of nested block lists.
Response
Correct selection condition and try again.
SAE5575
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5575 TOO MANY BLOCK LISTS IN SEQUENCE IN SELECTION CONDITION. STATEMENT NOT PROCESSED
Meaning
A pattern in the selection condition contains too many block lists
in sequence.
Response
Correct selection condition and try again.
SAE5576
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5576 A PATTERN IN SELECTION CONDITION REPRESENTS TOO LONG STRINGS. STATEMENT NOT PROCESSED
Meaning
All the strings which can belong to the set described by a pattern
are too long, regarding with the maximum length allowed for the field
for which the pattern is given.
Response
Correct selection condition and try again.
SAE5577
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5577 NO SELECTION CONDITION IS GIVEN. STATEMENT NOT PROCESSED
Meaning
An 'empty' selection condition is not allowed.
Response
Correct selection condition and try again.
SAE5599
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5599 'SELECT-RECORDS' NEGATIVE SPACE ON WORK FILE '(&00)' UNSUCCESSFUL. PROCESSING CONTINUES
Meaning
At the end of the selection, the FILE macro is called
with negative space values to release the unused space
in the work file '(&00)'.
This call has returned a bad return code.
SAE5600
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE5600 'SELECT-RECORDS' STATEMENT TERMINATED. '(&00)' RECORDS SELECTED
Meaning
There were (&00) records which satisfied the given selection criterion.
SAE6000
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE6000 DMS ERROR '(&00)' IN FILE '(&01)'. FURTHER INFORMATION: /HELP-MSG (&00)
Meaning
The program detected a DMS error during processing.
For more detailed information about the DMS error code enter
/HELP-MSG or see the BS2000 manual 'System Messages'.
Response
Reenter the statement after eliminating the error.
SAE6001
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE6001 DMS ERROR '(&00)' IN FILE '(&01)'. STATEMENT PROCESSING ABORTED. FURTHER INFORMATION: /HELP-MSG (&00)
Meaning
The program detected a DMS error during processing.
Statement processing has been aborted.
For more detailed information about the DMS error code, enter the
command /HELP-MSG or see the BS2000 manual
'System Messages'.
Response
Locate the source of the error and eliminate it; then reenter the
statement.
SAE6002
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE6002 DMS ERROR '(&00)' IN FILE '(&01)'. STATEMENT PROCESSING CONTINUES. FURTHER INFORMATION: /HELP-MSG (&00)
Meaning
The program detected a DMS error during processing.
Statement processing continues.
For more detailed information about the DMS error code enter
the command /HELP-MSG or see the BS2000 manual
'System Messages'.
SAE6003
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE6003 REQM ERROR. STATEMENT PROCESSING ABNORMALLY TERMINATED
Meaning
The program detected a REQM error during processing.
Response
Try again later or enter another evaluator statement.
SAE6004
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE6004 DMS ERROR '(&02)' : FILE '(&00)' CANNOT BE COPIED INTO FILE '(&01)'. STATEMENT NOT PROCESSED
Meaning
The program detected a DMS error during copy processing.
Statement processing has been aborted.
For more detailed information about the DMS error code enter
the command /HELP-MSG or see the BS2000 manual
'System Messages'.
Response
Try again later or enter another evaluator statement.
SAE6005
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE6005 FILE '(&00)' IS NOT A VALID SKP2 FILE. STATEMENT PROCESSING ABNORMALLY TERMINATED
Meaning
Either the first record of the SKP2 file is not a CHANGE-OF-DAY
record or one of the SKP2 records is not of the correct type.
Response
Contact the system administrator.
SAE6006
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE6006 FILE '(&00)' IS NOT A VALID CONSLOG FILE. STATEMENT PROCESSING ABNORMALLY TERMINATED
Meaning
Either the first record of the CONSLOG file is not a CHANGE-OF-DAY
record or one of the CONSLOG records is not of the correct type.
Response
Contact the system administrator.
SAE6008
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE6008 INTERNAL ERROR DURING PSEUDO-CLOSE ON FILE '(&00)'. STATEMENT PROCESSING CONTINUES
Meaning
Possible reasons:
- No current file is available.
- A DMS error occurred during the PSEUDO-CLOSE of the current file.
SAE6010
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE6010 ERROR '(&00)' IN FILE '(&01)' WHEN READING A RECORD. STATEMENT PROCESSING ABORTED
Meaning
During the processing an error occurred at one of the library
functions flocate or fread.
The statement processing has been aborted.
For more detailed information about the C functions see the
BS2000 manual 'C POSIX library'.
Response
Locate the source of the error and eliminate it; then reenter the
statement.
SAE6011
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE6011 ERROR '(&00)' IN FILE '(&01)' WHEN WRITING A RECORD. STATEMENT PROCESSING ABORTED
Meaning
During the processing an error occurred at the library
function fwrite.
The statement processing has been aborted.
For more detailed information about the C function see the
BS2000 manual 'C POSIX library'.
Response
Locate the source of the error and eliminate it; then reenter the
statement.
SAE6050
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE6050 ERROR DURING '(&00)' PROCESSING. RETURN CODE '(&01)'. STATEMENT PROCESSING ABNORMALLY TERMINATED
Meaning
Statement processing has been aborted due to an error.
(&00) : procedure in which the error occurred.
(&01) : return code of the procedure.
Response
Contact the system administrator.
SAE7000
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE7000 WORK FILE '(&00)' IS EMPTY. STATEMENT NOT PROCESSED
Meaning
No record has yet been selected in work file (&00) or the input
files of SATUT have been erased.
SAE7001
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE7001 'START-SELECTION' STATEMENT TERMINATED. '(&00)' RECORDS SELECTED IN WORK FILE '(&01)'
Meaning
(&00) records satisfied the selection condition defined
for the work file (&01).
SAE7002
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE7002 INPUT FILES ARE NOT AVAILABLE ANYMORE. STATEMENT NOT PROCESSED
Meaning
Input files have been erased by a previous SAVE-SELECTED-RECORDS
statement.
SAE7003
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE7003 WORK FILE '(&00)' CANNOT BE OVERWRITTEN. SELECTED RECORDS ARE IN FILE '(&01)'. STATEMENT PROCESSING CONTINUES
Meaning
Due to a DMS error, old content of work file (&00) cannot be
overwritten by its new content.
SAE7050
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE7050 SELECTION CONDITION '(&00)' ALREADY EXISTS. STATEMENT NOT PROCESSED
Meaning
Selection condition (&00) has already been defined.
Response
Choose another name for the new selection condition.
SAE7051
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE7051 SELECTION CONDITION '(&00)' DOES NOT EXIST. STATEMENT NOT PROCESSED
Meaning
Selection condition (&00) has not yet been defined.
SAE7052
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE7052 NO SELECTION CONDITION HAS BEEN DEFINED. STATEMENT NOT PROCESSED
SAE7053
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
SAE7053 NO ADDITIONAL SELECTION CONDITION CAN BE DEFINED. STATEMENT NOT PROCESSED
Meaning
There is no more place in internal tables of SATUT for additional
selection conditions.