Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN001 SYNTAX ERROR
Meaning
AML returns an error code due to :
- syntax error
- command invalid
- the specified requestor is not known to AMU
- the message with the sequence number is unknown
Response
Contact the maintenance staff if necessary.
ROBN002
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN002 UNEXPECTED RESPONSE FROM ROBOT
Meaning
AML returns an error code due to :
- A command in wrong format was sent.
- The given command contains an unknown option.
Command cannot be executed.
Response
Contact the maintenance staff if necessary.
ROBN003
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN003 SERIOUS ERROR IN SETUP FILE
Meaning
AML returns an error code due to :
- There is no entry in AMU.INI.
- AMUP can't open a file.
Response
Look at the installation guide and check your
entries in the configuration submenu. Contact the maintenance
staff if necessary.
ROBN004
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN004 SERIOUS ERROR IN ARCHIVE DATABASE
Meaning
AML returns an error code due to :
- A severe error in the archive database has occurred.
- The Data Base Manager reports a warning or an error.
- A database module wasn't bound successfully.
Response
Contact the maintenance staff if necessary.
ROBN005
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN005 ROBOT NOT READY
Meaning
AML returns an error code due to :
- Initialisation error : the modules .DLL cannot be loaded or
linked, perhaps due to PATH problems.
- Configuration error : cannot find the robot or drive.
- The robot is not available for the moment.
- Buffer overflow or unknown communication partner.
Response
Contact the maintenance staff if necessary.
ROBN006
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN006 ROBOT ERROR, SEE PRECEDING WARNING
Meaning
AML returns an error code due to :
- Command has been cancelled by AMU.
- Illegal argument.
Response
Contact the maintenance staff if necessary.
ROBN007
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN007 ERROR CONDITION CANNOT BE DIAGNOSED
Meaning
AML returns an error code due to :
- A sequence number has been used twice. Therefore, the second
command cannot be processed.
- The host sent more commands than executable all at once.
- Command cannot be executed in simulation or configuration mode.
- The desired robot is not known to AMU.
Response
Contact the maintenance staff if necessary.
ROBN008
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN008 ROBOT EMERGENCY SHUTDOWN
Response
Contact the maintenance staff if necessary.
ROBN009
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN009 ROBOT SWITCHED INTO SETUP MODE
Response
Contact the maintenance staff if necessary.
ROBN010
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN010 UNKNOWN ROBOT COMMAND
Meaning
AML returns an error code due to :
- The given message could not be identified. Try to detect,
whether the syntax of the message command was correct.
- Not supported command.
- The host command format was wrong.
Response
Contact the maintenance staff if necessary.
ROBN011
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN011 INVALID ASSIGNMENT E.G. ROBOT-VOLSER
Meaning
AML returns an error code due to :
- Coordinate is out of range.
- The desired coordinate is wrong.
- No robot could be selected. Either there is no robot attached
to the given coordinate(s) or these cannot be handled by the
same robot.
Response
Contact the maintenance staff if necessary.
ROBN012
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN012 COMMAND INTERRUPTED BY MANUAL INTERVENTION
Response
Contact the maintenance staff if necessary.
ROBN014
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN014 COMMAND INTERRUPTED BY PROGRAM REQUEST
Meaning
AML returns an error code due to :
- The command in process is being cancelled.
- A currently active mount request in CentricStor
was aborted by a KEEP request.
Response
Save diagnostic files and contact the maintenance staff if necessary.
ROBN015
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN015 TOWER HAS NOT TURNED INTO POSITION
Response
Contact the maintenance staff if necessary.
ROBN016
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN016 ROBOT HARDWARE ERROR
Meaning
AML returns an error code due to :
- Gripper problems (position, open/closed).
- Camera or vision system problems.
- Robot coordinate problems (out of range)
- Mismatch between robot entries in archive database and configuration
Response
Contact the maintenance staff if necessary.
ROBN017
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN017 COMMAND IS NOT EXECUTABLE
Meaning
A command sent from ROBAR to the AML system
could not be executed.
Response
Contact the maintenance staff if necessary.
ROBN100
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN100 UNEXPECTED ROBOT CRASH
Response
Contact the maintenance staff if necessary.
ROBN101
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN101 ROBOT CRASH AT VOLUME REMOVAL/REPLACEMENT
Meaning
AML returns an error code due to :
Crash sensor.
Response
Contact the maintenance staff if necessary.
ROBN102
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN102 TIMEOUT ROBOT
Meaning
AML returns an error code due to :
Timeout-error with robot/ tower / I/O box control
Response
Contact the maintenance staff if necessary.
ROBN103
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN103 TIMEOUT PC-IC COMMUNICATION
Response
Contact the maintenance staff if necessary.
ROBN104
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN104 VOLUME LOST
Meaning
AML returns an error code due to :
- Volume not in gripper.
- Volume lost.
Response
Contact the maintenance staff if necessary.
ROBN105
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN105 VOLUME STUCK IN GRAB
Meaning
AML returns an error code due to :
Volume in gripper.
Response
Contact the maintenance staff if necessary.
ROBN110
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN110 CRASH AT TAKING A VOLUME FROM A STORAGE LOCATION
Response
Contact the maintenance staff if necessary.
ROBN111
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN111 CRASH AT INSERTING A VOLUME INTO A STORAGE LOCATION
Response
Contact the maintenance staff if necessary.
ROBN112
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN112 CRASH AT TAKING A VOLUME FROM A DEVICE
Response
Contact the maintenance staff if necessary.
ROBN113
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN113 CRASH AT INSERTING A VOLUME INTO A DEVICE
Response
Contact the maintenance staff if necessary.
ROBN201
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN201 UNKNOWN TAPE DEVICE
Meaning
AML returns an error code due to :
The device is unknown to the archive database.
Response
Contact the maintenance staff if necessary.
ROBN202
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN202 DEVICE OCCUPIED (DETECTED BY SOFTWARE)
Meaning
AML returns an error code due to :
- The requested tape device is not empty (AMU archive database).
Response
Check the command, make an inventory on the requested
tape device. Contact the maintenance staff if necessary.
ROBN203
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN203 DEVICE EMPTY (DETECTED BY SOFTWARE)
Meaning
AML returns an error code due to :
The requested tape device is empty (AMU archive database).
Response
Check the command, make an inventory on the requested
tape device. Contact the maintenance staff if necessary.
ROBN204
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN204 DEVICE OCCUPIED (DETECTED BY ROBOT)
Meaning
AML returns an error code due to :
- The requested device is not empty (detected by robot).
Response
Check the command, make an inventory on the requested
device. Contact the maintenance staff if necessary.
ROBN205
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN205 DEVICE EMPTY (DETECTED BY ROBOT)
Meaning
AML returns an error code due to :
The requested position does not contain a tape (detected by
robot.
Response
Check the command, make an inventory on the requested
device. Contact the maintenance staff if necessary.
ROBN206
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN206 VOLUME CANNOT BE REMOVED FROM DEVICE
Meaning
AML returns an error code due to :
- Requested device is empty.
- Cover of requested device is closed.
Response
Contact the maintenance staff if necessary.
ROBN207
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN207 DRIVE DOOR CANNOT BE CLOSED
Meaning
AML returns an error code due to :
- Cover of requested device is open.
- The device cannot be closed.
Response
Contact the maintenance staff if necessary.
ROBN208
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN208 VOLUME CANNOT BE TAKEN FROM STACK
Meaning
Only involves devices with stacker (3490/3590)
Response
Contact the maintenance staff if necessary.
ROBN209
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN209 DEVICE/MEDIUM MISMATCH
Meaning
AML returns an error code due to a mount request for
a cartridge whose medium type does not match with
the medium type of the device
ROBN301
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN301 UNKNOWN VOLSER
Meaning
AML returns an error code due to :
- The given volser could not be found in the database.
Response
Contact the maintenance staff if necessary.
ROBN302
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN302 VOLSER NOT IN LIBRARY
Meaning
AML returns an error code due to :
- The requested position does not contain a volume (archive database).
- The requested source device is empty (archive database).
- The insert array does not contain a volume.
- The requested volume is not in a storage (ejected or mounted ?)
- There was no clean tape found in database.
- In conjunction with CentricStor a logical volume could have been
placed on a physical volume which is not accessible because of
a drive or volume error.
Response
Contact the maintenance staff if necessary.
ROBN303
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN303 VOLUME ALREADY MOUNTED ON THIS DEVICE
Meaning
AML returns an error code because the cartridge is
already mounted on the device.
Response
ROBAR will check if the tape is inside the device
or only in front of the device.
ROBN304
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN304 BARCODE LABEL NOT READABLE
Meaning
AML returns an error code due to :
- Barcode not recognised.
- Illegal barcode.
- Illegal range.
Response
Contact the maintenance staff if necessary.
ROBN305
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN305 NO BARCODE LABEL DETECTED OR NOT FOUND IN STORAGE POSITION
Meaning
AML returns an error code due to :
- Volume barcode label not recognised.
- The currently running insertion of volume is finished.
There wasn't found any volume in insert positions.
Response
Check the logfile for further information.
ROBN306
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN306 WRONG VOLSER ON SPECIFIED COORDINATE
Meaning
AML returns an error code due to :
- Illegal barcode.
- Inconsistency during inventory detected.
Response
Make an update to the archive database.
Contact the maintenance staff if necessary.
ROBN307
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN307 KEEP WAS SUCCESSFUL BUT A WRONG VOLSER WAS IN THE DEVICE
ROBN308
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN308 VOLUME EJECTED
Meaning
AML returns an error code because the cartridge to
be mounted has been ejected in the I/O box of the
robot system.
ROBN309
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN309 VOLUME ALREADY MOUNTED ON A DIFFERENT DEVICE
Meaning
AML returns an error code because the cartridge is
already mounted on another device.
ROBN401
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN401 COORDINATE NOT DEFINED
Meaning
AML returns an error code due to :
The given position could not be found in database.
Response
Contact the maintenance staff if necessary.
ROBN402
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN402 NO VOLSER ON SPECIFIED COORDINATE
Meaning
AML returns an error code due to :
Requested position is empty.
Response
Contact the maintenance staff if necessary.
ROBN403
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN403 COORDINATE SLOT NOT EMPTY
Meaning
AML returns an error code due to :
- The requested position is not empty (archive database).
- The requested target device is not empty (archive database).
Response
Contact the maintenance staff if necessary.
ROBN404
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN404 COORDINATE/MEDIUM MISMATCH
Meaning
AML returns an error code due to a request for a
cartridge whose medium type does not match with
the medium type of the specified coordinate.
ROBN405
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN405 NO MORE DYNAMIC POSITION IN THE ARCHIVE
Meaning
AML returns an error code because there is no more
free dynamic position in the robot system.
Response
Free place or add new dynamic positions in the
robot system.
ROBN408
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN408 GRIPPER ERROR, CARTRIDGE MAY HAVE BEEN DROPPED
ROBN501
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN501 DOOR OF I/O-UNIT NOT CLOSED
Response
Contact the maintenance staff if necessary.
ROBN502
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN502 I/O-AREA DEFINITIONS DO NOT MATCH
ROBN503
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN503 EJECT DEVICE OVERRUN
Meaning
AML returns an error code due to :
There is no free eject position in I/O box.
Response
Empty the I/O box. Try the command later.
ROBN504
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN504 VOLUME PUT INTO WASTE BOX
Meaning
AML returns an error code due to :
- The tape was moved to the problem box because of a severe error.
In case of CentricStor:
- The order cannot be executed because of file system error.
Response
Contact the maintenance staff if necessary.
ROBN505
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN505 VOLUME IN WASTE BOX NOW OCCUPIED
Response
Contact the maintenance staff if necessary.
ROBN507
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN507 COMMAND ABORTED. PROBLEMBOX FULL
ROBN700
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN700 NO CLEANING CARTRIDGES AVAILABLE
ROBN701
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN701 CLEAN POOL DOES NOT EXIST
ROBN900
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN900 AML COMMAND REJECTED
ROBN901
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN901 NO FREE STORAGE SLOT IN LIBRARY SYSTEM FOR IMPORT
Meaning
IMPORT cannot be started or continued because all
storage slots in the library system are occupied.
ROBN902
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN902 VOLUME TO BE EJECTED ALREADY EJECTED
ROBN903
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN903 VSN TO BE IMPORTED ALREADY EXISTS IN LIBRARY SYSTEM
Meaning
One of the volumes to be imported is labeled a volser,
which already exists in the library system.
This volume was not imported.
ROBN904
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROBN904 COMMUNICATION BETWEEN ROBAR-SV AND AML FAILED
Meaning
From ROBAR point of view the communication to a library
system with SCSI interface has failed. Possible reasons:
Problem in the library (e.g. Scalar i2000).
I/O blade failure.
Problems with the fibre channel path (e.g. switch).
Problems with the HBA of the ROBAR-SV host.
Response
If the problem cannot be solved contact the maintenance.
If the failure persists ROBAR-SV stops.
ROB0SAT
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB0SAT FROM ROBAR VIEW TAPE CARTRIDGE mmmm DEVICE IS ATTACHED
Meaning
When restarting, ROBAR requests the device status of the hosts
it is connected to. ROBAR sends an information message
when it considers a device to be attached to a BS2000 host.
Additional information:
- mmmm: device mnemonic
ROB0SER
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB0SER INCONSISTENCY IN AML DATABASE FOR DEVICE mmmm
Meaning
When restarting, ROBAR reports that BS2000 has found
a cartridge in the device, but the AML database
indicates that the device is empty.
Additional information:
- mmmm: device mnemonic
Response
Correct the AML database or contact the maintenance.
ROB0SKE
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB0SKE REMOVING TAPE CARTRIDGE FROM DEVICE mmmm
Meaning
When restarting, ROBAR has detected that a cartridge has to be
removed from the mentioned device.
Additional information:
- mmmm: device mnemonic
ROB0009
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0009 HOST UNKNOWN:
Meaning
The configuration file and the parameter file do not match.
Generate a new configuration file.
ROB0010
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0010 NO RESPONSE FROM AML FOR:
Meaning
AML has not sent a response within a certain time
(ROBAR_WAIT). Processing of the job by ROBAR is aborted.
Check whether the input/output window is open or whether
the robot is no longer operable.
ROB0011
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0011 MESSAGE CODE NOT FOUND IN MESSAGE_FILE:
Meaning
Error in the file message_file. Check message_file.
ROB0012
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0012 MESSAGE CODE NOT FOUND IN MESSAGE_XREF:
Meaning
Error in the file message_xref. Check message_xref.
ROB0013
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0013 MESSAGE CODE NOT FOUND IN ROBOTER_CMDS:
Meaning
Error in the file roboter_cmds. Check roboter_cmds.
ROB0014
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0014 ERROR IN COMMAND FILE:
Meaning
Error in the file roboter_cmds. Check roboter_cmds.
ROB0015
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0015 MESSAGE CODE NOT FOUND IN MESSAGE_RESP:
Meaning
Error in the file message_resp. Check message_resp.
ROB0016
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0016 Internal error detected in ROBAR-SV at (&00)
Meaning
ROBAR-SV has reported an internal error.
Diagnosis information is written into ROBAR-SV logging.
(&00): date and time of the error
ROB0018
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0018 INVALID MESSAGE CODE IN MESSAGE_XREF:
Meaning
The file message_xref contains an error. Check message_xref.
ROB0020
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0020 NO DEVICE FREE
Meaning
The mount job could not be performed as no drive is free.
The job is suspended if the appropriate specification was
made in the action list (REPEAT).
ROB0021
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0021 DEVICE UNKNOWN:
Meaning
The drive is not specified in the configuration file.
Modify the configuration file.
ROB0023
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0023 CONNECTION TO HOST SEVERED:
Meaning
The connection to the specified BS2000 system has been
severed.
ROB0024
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0024 ROBAR FREEPOOL NOT CREATED
Meaning
The specified freepool does not exist. Create the freepool.
ROB0027
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0027 ROBAR FREEPOOL IS EMPTY
Meaning
The freepool is empty. Extend the freepool.
ROB0028
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0028 FREEPOOL MINIMUM (MIN_SCRATCH) VIOLATED
Meaning
The freepool contains fewer volume serial numbers than are
specified in the MIN_SCRATCH variable. Extend the freepool.
ROB0029
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0029 ERROR IN DECLARE STATEMENT:
Meaning
An invalid keyword has been specified in DECLARE statement.
Correct the DECLARE statement in message_resp
ROB0030
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0030 DOOR OF I/O UNIT OPEN --> PLEASE CLOSE THE DOOR
Meaning
No cartridge can be ejected anymore.
Response
Close the door of the I/O box
and notify ROBAR after closing by means of the command
/INFORM-OPERATOR MESSAGE='<T I/O-BOX EMPTY'
or by the activation of the function that automatically
restarts the EJECT after an HICAP door has been closed
(this function has to be activated in the MRV30 option
of the file message_resp of ROBAR-SV).
ROB0031
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0031 ROBAR STOPPED
Meaning
The ROBAR system has been terminated.
ROB0032
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0032 CONFIRM EXECUTION (<CR>/N)
Meaning
This error only occurs in conjunction with simulation.
ROB0033
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0033 EXECUTED
Meaning
This error only occurs in conjunction with simulation.
ROB0034
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0034 NOT EXECUTED
Meaning
This error only occurs in conjunction with simulation.
ROB0035
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0035 I/O UNIT FULL --> PLEASE REMOVE CARTRIDGES
Meaning
No cartridge can be ejected anymore.
Response
Remove the cartridges from the I/O box
and notify ROBAR when it is empty by means of the command
/INFORM-OPERATOR MESSAGE='<T I/O-BOX EMPTY'
or by the activation of the function that automatically
restarts the EJECT after a HICAP door has been closed
(this function has to be activated in the MRV30 option
of the file message_resp of ROBAR-SV).
ROB0036
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0036 ERROR DETECTED DURING CLEANING ! DEV =
Meaning
An error has occurred while cleaning the specified drive.
Check the return code of the AML system.
ROB0037
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0037 INSERT COMMAND EXECUTED
ROB0038
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0038 ILLEGAL KEYWORD:
Meaning
The keyword defined in message_resp is not known in ROBAR.
Correct the file message_resp.
ROB0039
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0039 CLEAN CARTRIDGE EJECTED --> PLEASE INSERT NEW ONE
ROB0040
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0040 PROBLEM BOX FULL --> PLEASE REMOVE CARTRIDGES
ROB0042
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0042 ROBOT STATE CHANGED TO >OFF< : (&00)
ROB0043
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0043 ROBOT STATE CHANGED TO >ON< : (&00)
ROB0044
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0044 AMU STATE IS >PASSIVE<
ROB0045
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0045 AMU STATE IS >ACTIVE<
ROB0048
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB0048 HOST NOT AUTHORIZED TO USE THIS VSN: (&00)
Meaning
The format of (&00) is: vvvvvv,PARTNER=pppppppp,LOCATON=llllllll.
vvvvvv : VSN
pppppppp: TNS partner name
llllllll: location of the robot system.
A request received from ROBAR-CL with the TNS partner name pppppppp
is not authorized to use the cartridge vvvvvv in the configured
environment.
This message is issued only if vvvvvv is known in ROBAR_ARCHIV.
Response
Check ROBAR_ARCHIV and the section gen_hosts_vsn in the
configuration file of ROBAR-SV. Change if necessary.
ROB1000
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1000 USER ID HAS NO PRIVILEGE FOR TAPE ADMINISTRATION
Meaning
System privilege for tape administration is mandatory
for the desired function.
Response
Contact the system administrator.
ROB1010
Destination: USER-TASK, CONSOLE Routing code: T Weight: 98
Warranty : NO
ROB1010 CREATE-ROBAR-FREEPOOL POOL=(&00),VOLUME=(&01)
Meaning
Creation of a ROBAR freepool.
(&00) : type of freepool (*STD or *TSN)
(&01) : VSN of the tape cartridge
ROB1011
Destination: USER-TASK, CONSOLE Routing code: T Weight: 98
Warranty : NO
ROB1011 CREATE-ROBAR-FREEPOOL POOL=(&00),VOLUME=*INTERVAL((&01),(&02))
Meaning
Creation of a ROBAR freepool.
(&00) : type of freepool (*STD or *TSN)
(&01) : first VSN of the interval
(&02) : last VSN of the interval
ROB1013
Destination: USER-TASK, CONSOLE Routing code: T Weight: 98
Warranty : NO
ROB1013 ADD-ROBAR-VOLUME STATE=(&00),VOLUME=(&01),POSITION=(&02),ROB=(&03)
Meaning
Declaration of a foreign tape cartridge.
(&00) : classification (FOREIGN)
(&01) : VSN of the tape cartridge
(&02) : location of the tape cartridge (<integer 3..3>)
(&03) : robot system (1 or 2)
ROB1019
Destination: USER-TASK, CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB1019 END-ROBAR-FREEPOOL
Meaning
Internal termination message.
ROB1020
Destination: USER-TASK, CONSOLE Routing code: T Weight: 98
Warranty : NO
ROB1020 DELETE-ROBAR-FREEPOOL POOL=(&00)
Meaning
Deletion of a ROBAR freepool.
(&00) : type of freepool (TSN)
ROB1021
Destination: USER-TASK, CONSOLE Routing code: T Weight: 98
Warranty : NO
ROB1021 REMOVE-ROBAR-VOLUME STATE=(&00),VOLUME=(&01),LOCATION=(&02)
Meaning
Removal of a foreign tape cartridge.
(&00) : classification (FOREIGN)
(&01) : VSN of the tape cartridge
(&02) : location of the tape cartridge to be removed
ROB1030
Destination: USER-TASK, CONSOLE Routing code: T Weight: 98
Warranty : NO
ROB1030 EXPORT-ROBAR-VOLUME VOLUME=(&00),ROB=(&01),LOCATION=(&02)
Meaning
Export of a tape cartridge.
(&00) : VSN of the tape cartridge
(&01) : robot (1 or 2)
(&02) : location of the tape cartridge to be ejected
ROB1031
Destination: USER-TASK, CONSOLE Routing code: T Weight: 98
Warranty : NO
ROB1031 EXPORT-ROBAR-VOLUME KEEP-POSITION=*NO,VOLUME=(&00),ROB=(&01),LOCATION=(&02)
Meaning
Export of a tape cartridge.
(&00) : VSN of the tape cartridge
(&01) : robot (1 or 2)
(&02) : location of tape cartridge to be ejected
ROB1040
Destination: USER-TASK, CONSOLE Routing code: T Weight: 98
Warranty : NO
ROB1040 IMPORT-ROBAR-VOLUME STATE=(&00),ROB=(&01),LOCATION=(&02)
Meaning
Import of a tape cartridge
(&00) : classification (OWN)
(&01) : robot (1 or 2)
(&02) : location of tape cartridge to be imported
ROB1050
Destination: USER-TASK, CONSOLE Routing code: T Weight: 98
Warranty : NO
ROB1050 SHOW-ROBAR-VOLUME VOLUME=(&00),POSITION=(&01),LOCATION=(&02),ELEMENT=(&03)
Meaning
Show of FOREIGN definition in ROBAR-SV
(&00) : requested VSN or *ALL
(&01) : requested foreign position (*FRnnn) or *ALL
(&02) : location or *ANY
(&03) : sequence number of element in case of list
ROB1100
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1100 ROBAR-CL VERSION (&00) READY
ROB1105
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1105 ERROR WHEN READING STATEMENT (CODE: '(&00)')
Meaning
(&00): content of the register 15 when returning
from the call to RDSTMT interface.
ROBAR cannot handle any special action for this return code.
Response
- Look for a previous SDF message (CMDnnnn) that explains the error.
- Correct and retry.
ROB1110
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1110 COMMAND ACCEPTED
Meaning
The specified ROBAR command has been read, checked and accepted.
ROB1111
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1111 END OF FOREIGN VOLUME DEFINITION FOR SELECTION=(&00) AND LOCATION=(&01)
ROB1112
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1112 NO FOREIGN VOLUME DEFINITION EXISTS FOR SELECTION=(&00) AND LOCATION=(&01)
ROB1113
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1113 NO ROBAR_FOREIGN DEFINED IN ROBAR-SV. REQUESTED INFORMATION NOT AVAILABLE
Meaning
Possible reason: SCSI interface.
Foreign volumes are not supported in ROBAR-SV for SCSI interface.
ROB1114
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1114 ERROR IN FOREIGN DEFINITIONS. REQUESTED INFORMATION NOT AVAILABLE
ROB1115
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1115 INVALID COMMAND - PLEASE RETRY
Meaning
The specified command is invalid or illegal.
Response
Check the command and enter it again.
ROB1116
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1116 INVALID RESPONSE
Meaning
The response to the ROBAR message is invalid.
Response
Please do not manually respond to it.
ROB1120
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1120 ROBAR MESSAGE COULD NOT BE ISSUED
Meaning
An error has occurred in the MSG7 macro.
Response
Prepare the necessary documents for diagnosis.
ROB1121
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1121 ROBAR COULD NOT WRITE ON SYSOUT
Meaning
An error has occurred in the WROUT macro.
Response
Prepare the necessary documents for diagnosis.
ROB1122
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1122 ROBAR COULD NOT WRITE ON SYSLST01
Meaning
An error has occurred in the WRLST macro.
Response
Prepare the necessary documents for diagnosis.
ROB1125
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1125 ROBAR DOES NOT EXIST IN YOUR ACTIVATED SYNTAX FILES
Meaning
The ROBAR program is not known in the currently activated syntax files
as a collective term for all possible command inputs.
Response
Check the activated syntax files for the existence of the ROBAR
program. If necessary, merge the supplied syntax files again.
ROB1130
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1130 REQUESTED FILE IS EMPTY
Meaning
The specified file, which should contain the freepool specifications, is
empty.
Response
Recreate the file with the freepool specifications.
ROB1135
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1135 REQUESTED FILE IS PASSWORD-PROTECTED (READPASS)
Meaning
The file containing the freepool specifications is protected
by a read password.
Response
Either enter the required password or lift the password protection
before issuing the command.
ROB1140
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1140 OPEN ERROR
Meaning
The specified file could not be opened.
Response
Check the file access rights.
ROB1145
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1145 REQUESTED FILE IS NOT PRESENT
Meaning
The specified file does not exist.
Response
Create a file with the freepool specifications.
ROB1150
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1150 REQUESTED FILE IS NOT SHAREABLE
Meaning
The requested file is not shareable.
Response
Make the file shareable.
ROB1155
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1155 FSTAT MACRO EXECUTED WITH ERRORS
Meaning
An error occurred during executing of the FSTAT macro.
Response
Prepare the necessary documents for diagnosis.
ROB1160
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1160 FILE MACRO EXECUTED WITH ERRORS
Meaning
An error occurred during executing of the FILE macro.
Response
Prepare the necessary documents for diagnosis.
ROB1165
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1165 USER ERROR
Meaning
Control has branched to the USERERR exit of the file containing
the freepool specifications.
Response
Check the file and prepare the necessary documents for diagnosis.
ROB1170
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1170 VOLUME SERIAL NUMBERS HAVE DIFFERENT LENGTHS
Meaning
The VSN specifications have different lengths.
Response
Correct the VSN specifications so that they all have the same length.
ROB1175
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1175 ALPHANUMERIC VSN SPECIFICATIONS ARE INCONSISTENT
Meaning
The VSN specifications have different alphanumeric identifiers.
Response
Correct the VSN specifications so that they have the same identifiers.
ROB1180
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1180 FIRST VSN IS SAME AS SECOND VSN
Meaning
Two identical VSN's have been entered for the range specification.
Response
Correct the VSN entries so that they are not identical.
ROB1185
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1185 FIRST VSN IS GREATER THAN SECOND VSN
Meaning
The range specifications are not in ascending order.
Response
Correct the VSN specifications so that they are in ascending order.
ROB1190
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1190 PLEASE SPECIFY EXPORT-ROBAR-VOLUME COMMAND FOR EACH VSN OF THIS TYPE
Meaning
It is not possible to specify a range of EXPORT-ROBAR-VOLUME
commands for VSN's of the type G01A01 (alphanumeric identifier
not only at the beginning or end of the VSN).
Response
Enter the EXPORT-ROBAR-VOLUME commands individually.
ROB1195
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1195 POSITION OPERAND MUST CONTAIN 3 CHARACTERS
Meaning
The position specification in the output chute must contain 3 characters.
Response
Correct the position specification.
ROB1200
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1200 ROBAR TERMINATED
ROB1205
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1205 ROBAR TERMINATED WITH ERRORS
Response
Prepare the necessary documents for diagnosis.
ROB1500
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1500 A REFERENCE HAS BEEN CREATED TO THE FOREIGN TAPE CARTRIDGE
ROB1505
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1505 FOREIGN FILE ALREADY EXISTS
ROB1506
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1506 VSN OR POSITION INVALID OR ALREADY DEFINED
Meaning
Either the given POSITION is not defined in the
file ROBAR_FOREIGN or the given VSN or POSITION
is already used by a previous FOREIGN definition.
Foreign volumes and freepools are not supported in
ROBAR-SV for SCSI interface.
Response
Check the actual content of the FOREIGN definitions
by means of the command //SHOW-ROBAR-VOLUME
and retry with correct definition.
ROB1507
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1507 FOREIGN POSITION IS NOT UNIQUE
ROB1510
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1510 NO REFERENCE HAS BEEN CREATED TO FOREIGN TAPE CARTRIDGE
ROB1520
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1520 FOREIGN VSN '(&00)' RELEASED
ROB1525
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1525 CANNOT REMOVE FOREIGN DEFINITION (&00)
Meaning
Possible reasons:
- The specified volume does not exist in foreign definitions.
- The specified volume is mounted.
ROB1526
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1526 ROBAR-SV ERROR DURING REMOVAL OF FOREIGN DEFINITION OR WRONG LOCATION SPECIFIED
Meaning
Possible reasons:
- The specified LOCATION is wrong or rejected by ROBAR-SV
- The specified foreign definition cannot be removed by ROBAR-SV
Foreign volumes and freepools are not supported in
ROBAR-SV for SCSI interface.
Response
Check the foreign definitions with //SHOW-ROBAR-VOLUME
ROB1530
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1530 FOREIGN VSN '(&00)' NOT RELEASED
ROB1540
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1540 IMPORT OPERATION STARTED
ROB1550
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1550 IMPORT OPERATION NOT STARTED OR NOT COMPLETELY PROCESSED
ROB1560
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1560 VSN '(&00)' EXPORTED
ROB1565
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1565 ERROR AT MAREN SUBROUTINE CALL (VSN=(&00), RC=(&01))
Meaning
(&00): VSN of the tape cartridge
(&01): return code from MAREN. Possible values:
D : DMS error
I : Not allowed at the moment (for example,
because the imported volume is not yet declared
in the MAREN catalog)
M : MAREN internal error
N : Volume not found
O : Offline operation: only logging is activated.
The operation is not really registered in the
MAREN catalog
P : Concurrent access to the volume in the
MAREN catalog
T : Volume still allocated by another task
X : Request rejected by MAREN administrator
(MAREN exit routine)
0 : Operator reply: EXIT
1 : Operator reply: RETRY
2 : Operator reply: CONTINUE
ROB1570
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1570 VSN '(&00)' NOT EXPORTED
ROB1580
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1580 EXPORT OPERATION ABORTED OR WRONG LOCATION SPECIFIED
ROB1590
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1590 VSN '(&00)' ADDED TO FREEPOOL
ROB1593
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1593 INCONSISTENCY DETECTED WHEN CREATING THE FREEPOOL
ROB1594
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1594 SYNTAX ERROR IN VSN SPECIFICATION
ROB1595
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1595 VSN '(&00)' IS NOT UNIQUE IN THE FREEPOOL
ROB1596
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1596 VSN '(&00)' IS NOT KNOWN IN ROBAR_ARCHIV
ROB1599
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1599 ERROR IN OPENING FREEPOOL FILE
ROB1600
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1600 FREEPOOL NOT CREATED
ROB1605
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1605 FREEPOOL CREATED
ROB1610
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1610 TSN FREEPOOL DELETED
ROB1620
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1620 CANNOT DELETE TSN FREEPOOL
ROB1630
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1630 TSN FREEPOOL WAS NOT CREATED
ROB1640
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB1640 INCONSISTENCY DETECTED WHEN DELETING THE TSN FREEPOOL
ROB2000
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB2000 ROBAR CONNECTION STARTED
Meaning
Connection to ROBAR-SV has been established.
ROB2001
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB2001 ROBAR CONNECTION CLOSED
Meaning
Connection to ROBAR-SV has been severed.
ROB2005
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB2005 FILE (&00).TEXT MISSING
Meaning
(&00): Prefix of TEXT file
ROB2010
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB2010 APPLICATION (&00) COULD NOT BE OPENED (RC=(&01))
Meaning
The $CONSOLE interface is locked for this application.
(&00): application name
(&01): DCAM return code
ROB2020
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB2020 CONNECTION TO ROBAR-SV COULD NOT BE SET UP (RC=(&00))
Meaning
(&00): DCAM return code
ROB2030
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB2030 CONNECTION ATTEMPT FROM WRONG STATION: (&00)/(&01)
Meaning
(&00): station name
(&01): processor name
ROB2040
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB2040 ERROR IN PASSWORD FROM ROBAR-SV
ROB2050
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB2050 ERROR DURING SENDING A MESSAGE (RC=(&00))
Meaning
(&00): DCAM return code
ROB2051
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB2051 ERROR DURING PICKING UP A MESSAGE (RC=(&00))
Meaning
(&00): DCAM return code
ROB2052
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB2052 CONNECTION TO ROBAR-SV COULD NOT BE TORN DOWN (RC=(&00))
Meaning
ROBAR-CL has received the negative return code (&00) from DCAM.
The connection to ROBAR-SV will NOT be reestablished automatically.
Response
The system administrator should solve the DCAM problem.
Then ROBAR-CL can be stopped and restarted.
ROB2100
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB2100 ROBAR-CL-DCAM (&00) READY
ROB2110
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB2110 CONNECTION SET UP ( ROBAR-SV ) CPUS=(&00) (&01) STATION: (&02)/(&03)
ROB2120
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB2120 CONNECTION SET UP (UCON: (&00) ) (&01)
ROB2130
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB2130 CONNECTION CLEARED DOWN ( ROBAR-SV ) (&00)
ROB2140
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB2140 CONNECTION CLEARED DOWN (UCON) (&00)
ROB2200
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB2200 PARAMETER ERROR
ROB2210
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB2210 -C=(&00) IS NOT FOUR CHARACTERS LONG
Meaning
(&00): name of $CONSOLE application
ROB2220
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB2220 CONNECTION TO $CONSOLE COULD NOT BE SET UP (RC=(&00))
Meaning
(&00): DCAM return code
ROB2225
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB2225 CONNECTION TO $CONSOLE VIA DYNAMIC AUTHORISATION NAME REJECTED
Meaning
possible reasons:
- password for Operator-Id (TSOS) invalid or missing
- connection to UCON severed
Response
check password for Operator-Id, restart ROBAR-CL
ROB2226
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB2226 REQ-OPERATOR-ROLE REJECTED BY NBR0984. REASON: (&00)
Meaning
For further informations enter /HELP-MSG NBR0984.
Invalid combination of parameters OPEROLE (operator role)
and OPERID (operator identifier). ROBAR-CL is terminated.
Response
Change parameters OPERID and/or OPEROLE in ROBAR-CL start procedure
ROB2230
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB2230 JOB VARIABLE >(&00)< UNKNOWN OR JV SOFTWARE NOT INSTALLED
ROB2240
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB2240 PROGRAM CANNOT BE STARTED IN BS2000 V9.5
ROB2250
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB2250 ERROR AT MAREN CALL FOR VSN (&01): RETURN CODE = >(&00)<
Meaning
(&00): return code from MAREN. Possible values:
D : DMS error
I : Not allowed at the moment (for example,
because the imported volume is not declared
in the MAREN catalog yet)
M : MAREN internal error
N : Volume not found
O : Offline operation: only logging is activated.
The operation is not really registered in the MAREN catalog
P : Concurrent access to the volume in the MAREN catalog
T : Volume still allocated by another task
X : Request rejected by MAREN administrator (MAREN exit routine)
0 : Operator reply: EXIT
1 : Operator reply: RETRY
2 : Operator reply: CONTINUE
(&01): VSN of the tape cartridge
The next ROBAR message also gives a MAREN message number
that explains the cause of the error
ROB2260
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB2260 MAREN MESSAGE NUMBER: >(&00)<
ROB2270
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB2270 FILE >(&00)< CANNOT BE OPENED
ROB2280
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB2280 GET-TIME RETURNS VALUE 0. ROBAR-CL CANNOT BE STARTED
Meaning
The time returned by CRTE is not correct so that
ROBAR cannot properly run.
Response
Check the load address of GET-TIME subsystem.
ROB2290
Destination: USER-TASK Routing code: Weight: 99
Warranty : NO
ROB2290 ERROR IN FILE >(&00)< FOR >(&01)<
ROB4001
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4001 THE DEVICE IS IN NOT-READY STATUS (DEV=mmmm)
Meaning
The possible reasons are:
1. The device is not installed.
2. The device is not on-line.
3. No cartridge is loaded.
4. The READY/NOT-READY switch of the device has been set to NOT-READY.
5. The device is not functional.
6. The device is performing a REWIND-UNLOAD operation.
Additional information:
- mmmm: device mnemonic
Response
Check the READY/NOT-READY switch of the device.
If the problem cannot be solved, contact the maintenance.
ROB4002
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4002 THE POSITION OF THE TAPE DURING OPERATION IS NOT KNOWN ANYMORE (DEV=mmmm / TSN=tttt / VSN=vvvvvv)
Meaning
ROBAR has cancelled the remounting of the tape and the current I/O is
terminated with error.
Additional information:
- mmmm: device mnemonic
- tttt: Task Serial Number
- vvvvvv: Volume Serial Number
Response
Check the cause for the loss of position.
ROB4004
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4004 TAPE CARTRIDGE DEVICE UNLOADED (DEV=mmmm / VSN=vvvvvv)
Meaning
The AML system has moved the cartridge from the device to its
home place in the archive.
Additional information:
- mmmm: device mnemonic
- vvvvvv: Volume Serial Number
ROB4005
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4005 TAPE CARTRIDGE DEVICE UNLOADED (DEV=mmmm)
Meaning
The AML system has moved a cartridge from the device
to its home place in the archive.
Additional information:
- mmmm: device mnemonic
ROB4006
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4006 TAPE CARTRIDGE DEVICE NOT UNLOADED (DEV=mmmm / ffff)
Meaning
The AML system could not move the cartridge from the device
to its home place in the archive.
Additional information:
- mmmm: device mnemonic
- ffff: error code returned by the AML system
(issue a /HELP-MSG ROBffff command to get its meaning)
ROB4008
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4008 TAPE CARTRIDGE MOUNTED (DEV=mmmm / TSN=tttt / VSN=vvvvvv)
Meaning
Additional information:
- mmmm : device mnemonic
- tttt : Task Serial Number
- vvvvvv: Volume Serial Number
ROB4010
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4010 VOLUME ALLOCATED FROM ROBAR FREE-POOL (VSN=vvvvvv / TSN=tttt)
Meaning
Additional information:
- vvvvvv: Volume Serial Number
- tttt : Task Serial Number
ROB4011
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4011 ROBAR FREEPOOL IS EMPTY. REQUEST REJECTED (TSN=tttt)
Meaning
The freepool is empty. Extend the freepool.
Additional information:
- tttt: Task Serial Number
ROB4014
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4014 TAPE CARTRIDGE DEVICE IS UNEXPECTEDLY EMPTY (TSN=tttt / ffff)
Meaning
The AML system has returned an error code according to which
the concerned device is unexpectedly empty.
Additional information:
- tttt: Task Serial Number
- ffff: error code returned by the AML system
(issue a /HELP-MSG ROBffff command to get its meaning)
Response
Check a possible inconsistency between the real device
status and the AML system data base. In case of
inconsistency, correct the data base.
ROB4018
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4018 TAPE CARTRIDGE DEVICE CLEANED (DEV=mmmm)
Meaning
The device has been cleaned.
Additional information:
- mmmm: device mnemonic
ROB4019
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4019 TAPE CARTRIDGE DEVICE CLEANING WILL BE STARTED (DEV=mmmm)
Meaning
The device will be cleaned.
Additional information:
- mmmm: device mnemonic
ROB4020
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4020 TAPE CARTRIDGE DEVICE CLEANING FAILED (DEV=mmmm)
Meaning
The device cleaning has failed.
Additional information:
- mmmm: device mnemonic
Response
Check the problem with the device (see previous messages).
Check the cleaning information on the robot.
ROB4021
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4021 NEW CLEANING CARTRIDGES REQUIRED (CLEANPOOL=aaa)
Meaning
New cleaning cartridges are required for the specified cleanpool.
Additional information:
- aaa: cleanpool
Response
Insert new cleaning cartridges for the specified cleanpool.
ROB4022
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4022 NO CLEANING CARTRIDGE AVAILABLE (DEV=mmmm)
Meaning
No cleaning cartridges are available for the device.
Additional information:
- mmmm: device mnemonic
Response
Insert cleaning cartridges into the I/O box.
ROB4024
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4024 THE DEVICE IS UNEXPECTEDLY IN OFFLINE STATUS (DEV=mmmm)
Meaning
The possible reasons are:
1. The device is not powered.
2. The ONLINE/OFFLINE switch of the device has been pressed.
3. Hardware malfunction of the device.
4. Incompatibility between the device and the control unit.
Additional information:
- mmmm: device mnemonic
Response
Check the ONLINE/OFFLINE switch and the power of the device.
If the problem cannot be solved, contact the maintenance.
ROB4028
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4028 AUTOMATIC INVENTORY COMPLETED (LOCATION=llllllll / I/O-UNIT=aaa-bb)
Meaning
Automatic inventory completed after Hicap access.
Inventoried volumes are now available for mounting.
Additional information:
- llllllll : LOCATION
- aaa-bb : I/O box identification
ROB4034
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4034 VOLUME ALREADY MOUNTED (DEV=mmmm / TSN=tttt / VSN=vvvvvv)
Meaning
The volume is already mounted. ROBAR rejects the mount request.
Additional information:
- mmmm : device mnemonic
- tttt : Task Serial Number
- vvvvvv: Volume Serial Number
ROB4036
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4036 MOUNT FOR NON-ASSIGNED DEVICE (DEV=mmmm)
Meaning
ROBAR has detected that the requested device is not assigned
and has redirected the mount request to another device by
means of a /CHANGE-TAPE-MOUNT ACTION=*MOVE command.
Additional information:
- mmmm: device mnemonic
ROB4038
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4038 HARDWARE ERROR ON DEVICE CONTROLLER
Meaning
A previous BS2000 error message reported a hardware error.
If no alternative path is possible, ROBAR detaches the device.
Additional information:
- mmmm: device mnemonic
Response
Check the connection between the device and its controller.
If the problem cannot be solved, contact the maintenance.
ROB4040
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4040 BECAUSE OF A /SECURE-RESOURCE-ALLOCATION NO /CHANGE-TAPE-MOUNT IS ALLOWED (DEV=mmmm / VSN=vvvvvv)
Meaning
To bypass a problem with a device, ROBAR has issued a
/CHANGE-TAPE-MOUNT command.
But a previous /SECURE-RESOURCE-ALLOCATION prevents the usage
of another device and the request remains pending.
Additional information:
- mmmm : device mnemonic
- tttt : Task Serial Number
- vvvvvv: Volume Serial Number
Response
Check the problem with the device (see previous messages).
- If it can be solved, REMOUNT the cartridge.
- If it cannot be solved, reject the MOUNT request.
ROB4045
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4045 NO FREE STORAGE PLACE IN ARCHIVE FOR IMPORT
Meaning
IMPORT cannot be started or continued because all storage places in
the archive are occupied.
ROB4046
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4046 VSN OF VOLUME TO BE IMPORTED ALREADY EXISTS IN ARCHIVE
Meaning
One of the volumes to be imported is labeled a volser, which already
exists in the archive. This volume was not imported.
ROB4047
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4047 EXPIRED CLEANING CARTRIDGE EJECTED. INSERT NEW ONE
Meaning
An expired cleaning cartridge has been ejected and should be replaced
by a new one.
ROB4050
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4050 HICAP REQUEST BY OPERATOR (LOCATION=llllllll / I/O-UNIT=aaa)
Meaning
An Hicap request has been initiated .
Further robot requests will be stacked until the robot will be
available again.
Additional information:
- llllllll : LOCATION of the ROBOT
- aaa : I/O box identification
ROB4051
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4051 EIF OR HICAP OPENED BY OPERATOR (LOCATION=llllllll / I/O-UNIT=aaa-bb)
Meaning
Additional information:
- llllllll : LOCATION of the ROBOT
- aaa-bb : I/O box identification
ROB4052
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4052 HICAP CAN NOW BE OPENED BY OPERATOR (LOCATION=llllllll)
Meaning
Additional information:
- llllllll : LOCATION of the ROBOT
ROB4054
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4054 ROBOT AVAILABLE AGAIN AFTER HICAP REQUEST (LOCATION=llllllll)
Meaning
A Hicap request has been completed.
The robot is available again.
Additional information:
- llllllll : LOCATION of the ROBOT
ROB4060
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4060 AMU SWITCHING STARTED - ROBAR_RESTART INITIATED
Meaning
An AMU switching is currently in progress.
ROBAR-SV is now trying to restart the connection with the new AMU.
ROB4064
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4064 SWITCHING FAILED - NO AMU TO AMU COMMUNICATION
Meaning
Communication to the other AMU could not be established.
The previous AMU remains active.
The switching operation terminates.
Response
Check the error cause of the AML system.
If the problem cannot be solved, contact the maintenance.
ROB4068
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4068 ADS SWITCHING FAILED
Meaning
An error occurred during a switch operation of the ADS.
The switching operation cannot be executed and terminates.
The previously active AMU remains active.
Response
Check the error cause of the AML system.
If the problem cannot be solved, contact the maintenance.
ROB4070
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4070 WARNING : DEVICE NOT READY (DEVICE = hhh)
Meaning
The switching operation for the ADS succeeded,
but the hardware check reported following error:
One or more devices are not ready.
The device that did not report a ready state requires activation.
Additional information:
hhh : device identification in the AML
ROB4074
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4074 AMU SWITCHING COMPLETED
Meaning
The switching operation completed. The ADS was switched
successfully and a hardware check was issued.
ROB4078
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4078 CONNECTION TO AML SYSTEM LOST - RESTART OPTION SET
Meaning
The connection to the AML system has been lost.
For ROBAR-SV the automatic restart has been activated by
SET_RESTART_OPTION YES.
ROBAR-SV will be stopped and restarted.
The restart can only be successful, if the connection to the AML system
can be reestablished.
If an alternative AMU address is defined in the current configuration,
this address will be used for restart.
ROB4079
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4079 CONNECTION TO AML SYSTEM LOST - RESTART OPTION NOT SET
Meaning
The connection to the AML system has been lost.
For ROBAR-SV the automatic restart has been deactivated by
SET_RESTART_OPTION NO.
ROBAR-SV will be stopped.
ROB4080
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4080 AMU TO AMU COMMUNICATION LOST
Meaning
The communication path between the two AMU is interrupted.
The databases cannot be synchronised.
Response
Check the communication path between the two AMU.
If the problem cannot be solved, contact the maintenance.
ROB4084
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4084 AMU TO AMU COMMUNICATION ESTABLISHED
Meaning
Interrupted communication path between the two AMU is operable again.
ROB4090
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB4090 COMMUNICATION BETWEEN ROBAR-SV AND AML FAILED
Meaning
From ROBAR point of view the communication to an archive system with
SCSI interface has failed. Possible reasons:
Problem in the library (e.g. Scalar i2000).
I/O blade failure.
Problems with the fibre channel path (e.g. switch).
Problems with the HBA of the ROBAR-SV host.
Response
If the problem cannot be solved contact the maintenance.
If the failure persists ROBAR-SV stops.
ROB5004
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB5004 ERROR IN AML SYSTEM DATA BASE (ffff / VSN=vvvvvv), CONTACT MAINTENANCE
Meaning
The AML system has an internal error in its data base and has reported
it by means of an error code.
Additional information:
- ffff: error code returned by the AML system
(issue a /HELP-MSG ROBffff command to get its meaning)
- vvvvvv: Volume Serial Number, if known by ROBAR
Response
Check the integrity of the data base of the AML system.
If the problem cannot be solved, contact the maintenance.
ROB5005
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB5005 AML NOT READY FOR OPERATION (VSN=vvvvvv / ffff). CONTACT SYSTEM ADMINISTRATOR
Meaning
The AML system is not ready and has reported its status by means of
an error code.
Additional information:
- vvvvvv: Volume Serial Number, if known by ROBAR
- ffff : error code returned by the AML system
(issue a /HELP-MSG ROBffff command to get its meaning)
Response
Check the cause of the error of the AML system.
If the problem cannot be solved, contact the maintenance.
ROB5011
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB5011 INVALID ASSIGNMENT (DEV=mmmm / ffff / VSN=vvvvvv). CONTACT SYSTEM ADMINISTRATOR
Meaning
The AML system has received a request for a device or cartridge
whose coordinate is not accessible by the specified robot arm.
Possible reasons:
1. The declaration of the cartridge in the MAREN catalog is wrong.
2. The cartridge has been inserted into the AML system via a wrong
Input Box.
3. The AML configuration is wrong.
4. The device is assigned to the wrong robot arm in the ROBAR
configuration.
Additional information:
- mmmm: device mnemonic
- ffff: error code returned by the AML system
(issue a /HELP-MSG ROBffff command to get its meaning)
- vvvvvv: Volume Serial Number
Response
Declare the cartridge with the correct LOCATION in MAREN or eject it
from the AML system and insert it again via the right Input Box.
ROB5025
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB5025 CANNOT EMPTY THE DEVICE (DEV=mmmm). CONTACT SYSTEM ADMINISTRATOR
Meaning
A cartridge remains in the device and cannot be removed by the AML
system.
The device is probably defective and cannot be used without
risk of additional problems. Either ROBAR has therefore issued
a DETACH-DEVICE command or ROBAR has set an internal indicator
to prevent any further usage of the device.
Additional information:
- mmmm: device mnemonic
Response
Remove the cartridge manually from the device and update the
AML system data base to keep consistent information.
Check the previous error messages to find the source of error.
When it is eliminated, the device has to be attached again.
Thereby the internal lock in ROBAR will also be reset.
If the problem cannot be solved, contact the maintenance.
ROB5026
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB5026 CANNOT REMOVE TAPE CARTRIDGE FROM DEVICE, INIT REJECTED (DEV=mmmm / ffff). CONTACT SYSTEM ADMINISTRATOR
Meaning
A cartridge remains in the device and cannot be removed by the AML system.
The current INIT or LIST request has been rejected because it cannot be
fulfilled on another device.
The device is probably defective and cannot be used without risk of
additional problems. ROBAR has therefore issued a DETACH-DEVICE
command to prevent any further usage of the device.
Additional information:
- mmmm: device mnemonic
- ffff: error code returned by the AML system
(issue a /HELP-MSG ROBffff command to get its meaning)
Response
Remove the cartridge from the device manually and update the AML system
database to keep consistent information.
Check with previous error messages the error cause and attach
the device when it is corrected.
Issue the INIT or LIST request again.
If the problem cannot be solved, contact the maintenance.
ROB5027
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB5027 CANNOT CLOSE COVER. (DEV=mmmm / ffff / VSN=vvvvvv). CONTACT SYSTEM ADMINISTRATOR
Meaning
The AML system cannot close the cover of the device.
Either the mount request has been redirected to another device
by means of a /CHANGE-TAPE-MOUNT ACTION=*MOVE command or,
in case of an INIT or LIST, the request has been rejected
because another device cannot be used.
The device cannot be used without risk of additional problems.
ROBAR has therefore issued a DETACH-DEVICE command to prevent
any further usage of the device.
Additional information:
- mmmm : device mnemonic
- ffff : error code returned by the AML system
(issue a /HELP-MSG ROBffff command to get its meaning)
- vvvvvv: Volume Serial Number
Response
Check the device cover and verify the teaching of the AML system.
Attach the device when the error is corrected.
In case of INIT or LIST request, issue it again.
If the problem cannot be solved, contact the maintenance.
ROB5101
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB5101 ROBOT CRASH IN TOWER OR DEVICE OR STORAGE LOCATION (DEV=mmmm / ffff /VSN=vvvvvv). CONTACT SYSTEM ADMINISTRATOR
Meaning
The AML system cannot remove or replace a cartridge.
The current request for the device is pended.
In some cases, ROBAR has issued a DETACH-DEVICE command to prevent
usage of a defective device.
Additional information:
- mmmm: device mnemonic
- ffff: error code returned by the AML system
(issue a /HELP-MSG ROBffff command to get its meaning)
- vvvvvv: Volume Serial Number
Response
Check the AML system. Especially control the teaching and
the robot sensor. Attach the device when the error is corrected.
If the problem cannot be solved, contact the maintenance.
ROB5104
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB5104 LOST CARTRIDGE FROM GRIPPER (DEV=mmmm / ffff / VSN=vvvvvv). CONTACT SYSTEM ADMINISTRATOR
Meaning
The cartridge has been lost from the gripper of the robot.
Possible reasons are:
1. The sensor of the robot is defective.
2. The gripper of the robot is defective.
3. There is a teaching problem of the robot.
4. The cartridge cannot be taken by the robot because it is defective.
5. The cartridge cannot be taken by the robot because a device is
defective.
Additional information:
- mmmm: device mnemonic
- ffff: error code returned by the AML system
(issue a /HELP-MSG ROBffff command to get its meaning)
- vvvvvv: Volume Serial Number
Response
Check the AML system. Especially control the teaching, the robot sensor
and the gripper.
Check the device and cartridge status.
If the problem cannot be solved, contact the maintenance.
ROB5209
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB5209 MISMATCH BETWEEN CARTRIDGE TO BE MOUNTED AND THE DEVICE TYPE (DEV=mmmm / ffff / VSN=vvvvvv).
Meaning
The device does not support the cartridge type.
The declaration of the cartridge in the MAREN catalog is wrong or the
cartridge has been inserted into the AML system via a wrong I/O Box.
Additional information:
- mmmm : device mnemonic
- ffff : error code returned by the AML system
(issue a /HELP-MSG ROBffff command to get its meaning)
- vvvvvv: Volume Serial Number
Response
Declare the cartridge with the correct DEVICE-TYPE in MAREN catalog
or eject it from the AML system and insert it again via the
appropiate Input Box.
ROB5301
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB5301 VOLUME IS UNKNOWN TO AML SYSTEM DATA BASE (TSN=tttt / ffff / VSN=vvvvvv)
Meaning
Possible reasons are:
1. The cartridge has not been inserted in the AML system.
2. The definition of the volume in the MAREN catalog is wrong.
3. The data base of the AML system is damaged.
Additional information:
- tttt: Task Serial Number
- ffff: error code returned by the AML system
(issue a /HELP-MSG ROBffff command to get its meaning)
- vvvvvv: Volume Serial Number
Response
Check the integrity of the data base of the AML system, the MAREN
definition of the volume or insert the cartridge into the AML system.
If the problem cannot be solved, contact the maintenance.
ROB5302
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB5302 CARTRIDGE STORAGE PLACE IS EMPTY (TSN=tttt / ffff / VSN=vvvvvv)
Meaning
Possible reasons are:
1. The cartridge is not at the right place in the AML system.
2. The cartridge has been ejected from the AML system.
3. The cartridge is already mounted on another device.
4. The cartridge is already mounted on the device.
5. The data base of the robot system is damaged.
6. In conjunction with CentricStor a logical volume could have been
placed on a physical volume which is not accessible because
of a drive or volume error.
Additional information:
- tttt : Task Serial Number
- ffff : error code returned by the AML system
(issue a /HELP-MSG ROBffff command to get its meaning)
- vvvvvv: Volume Serial Number
Response
If the cartridge is already mounted on a device, check with
previous messages if two mount requests have been issued
for the same volume. Otherwise check the consistency of the
data base of the AML system with the real cartridge position.
If the problem cannot be solved, contact the maintenance.
ROB5303
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB5303 CARTRIDGE ALREADY MOUNTED ON OTHER DEVICE (TSN=tttt / VSN=vvvvvv)
Meaning
Additional information:
- tttt : Task Serial Number
- vvvvvv: Volume Serial Number
Response
Check by means of the previous messages if two mount requests have
been issued for the VSN.
ROB5304
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB5304 ROBOT SYSTEM CANNOT READ BARCODE LABEL (VSN=vvvvvv / ffff)
Meaning
Possible reasons:
1. The barcode of the cartridge is damaged.
2. The barcode reader of the AML system is defective.
3. There is no barcode on the cartridge.
Additional information:
- vvvvvv: Volume Serial Number
- ffff : error code returned by the AML system
(issue a /HELP-MSG ROBffff command to get its meaning)
Response
The problem can be temporarily bypassed by an option in the
roboter_cmds file of ROBAR-SV that allows to switch reading of
barcode to OFF for all operations, the initialisation excepted.
If the same error occurs several times, check the barcode reader
of the AML system.
If the problem cannot be solved, contact the maintenance.
ROB5305
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB5305 NO CARTRIDGE FOUND IN SPECIFIED INSERT AREA (TSN=tttt / ffff)
Meaning
Possible reasons are:
1. The cartridge(s) to be inserted is (are) not in INPUT area of the
I/O box of the AML system.
2. The cartridge(s) to be inserted is (are) in the I/O box of the other
robot-arm.
3. The number of I/O box is not correctly specified in the
ROBOT_INPUT_AREA shell variable of ROBAR.
Additional information:
- tttt: Task Serial Number
- ffff: error code returned by the AML system
(issue a /HELP-MSG ROBffff command to get its meaning)
Response
Check if the cartridge(s) is (are) in the correct I/O box.
If the robot has several I/O boxes (multimedia robot system), check if
the ROBOT_INPUT_AREA shell variable of ROBAR is correct.
ROB5306
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB5306 UNEXPECTED CARTRIDGE IS FOUND AT THE STORAGE PLACE OF VOLUME=vvvvvv
Meaning
The possible reasons are:
1. The label of the volume is damaged and could not be read.
2. Some cartridges have been interchanged in the AML system.
3. The data base of the AML system is damaged or incorrect.
Additional information:
- vvvvvv: Volume Serial Number
Response
Check for the consistency of the data base of the AML system
with regard to the real position of the cartridges and correct
either the data base or the position of the cartridges.
If the problem cannot be solved, contact the maintenance.
ROB5503
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB5503 I/O-BOX IS FULL (VSN=vvvvvv / ffff). CONTACT OPERATOR
Meaning
No cartridge can be ejected anymore.
Additional information:
- vvvvvv: Volume Serial Number
- ffff : error code returned by the AML system
(issue a /HELP-MSG ROBffff command to get its meaning)
Response
Remove the cartridges from the output area of the I/O box
and notify ROBAR when it is empty by means of the command
/SEND-MESSAGE TO=OPERATOR,MESSAGE='<T I/O-BOX EMPTY'.
ROB6060
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB6060 WRONG VOLUME MOUNTED (DEV=mmmm / TSN=tttt / VSN=vvvvvv)
Meaning
A volume has been mounted that does not fulfill the
system request. According to the options set by the user :
- the mount request cannot be satisfied. Volume processing
is terminated.
- the system protection is bypassed
Additional information:
- mmmm : device mnemonic
- tttt : Task Serial Number
- vvvvvv: Volume Serial Number of requested volume
Response
Contact the system administrator, if necessary.
ROB6062
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB6062 VOLUME IS WRITE-PROTECTED (VSN=vvvvvv / TSN=tttt)
Meaning
The volume processing is terminated and the volume is put back at
its storage place.
Additional information:
- vvvvvv: Volume Serial Number
- tttt : Task Serial Number
Response
Possible action:
Remove the write protection on the medium.
ROB6068
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB6068 AN IRRECOVERABLE ERROR HAS OCCURRED (DEV=mmmm / ffff / TSN=tttt / VSN=vvvvvv)
Meaning
The AML system has sent an error code that ROBAR cannot handle
autonomously.
Additional information:
- mmmm : device mnemonic
- ffff : error code returned by the AML system
(issue a /HELP-MSG ROBffff command to get its meaning)
- tttt : Task Serial Number
- vvvvvv: Volume Serial Number
Response
Contact the maintenance, if necessary.
ROB6069
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB6069 EITHER TOO MANY OR UNRECOVERABLE HARDWARE ERRORS ON DEVICE (DEV=mmmm)
Meaning
Too many hardware errors occurred, in sequence, on the same device.
The action requested by options MRV26 has been started for the job and
MRV24 has been started for the device.
These options can be found and modified in the file
message/message_resp of ROBAR-SV.
Exception: if the mount has been directly requested by MAREN,
it is always rejected with the response "N".
Additional information:
- mmmm: device mnemonic
Response
Fix the error. Contact the maintenance, if necessary.
After the error has been fixed, in certain circumstances the
device error counter has to be reset manually by the command
/SEND-MESSAGE TO=OPERATOR,MESSAGE='<T DEVICE mmmm REPAIRED'
resp. INFORM-OPERATOR MSG='<T DEVICE mmmm REPAIRED'.
ROB6070
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB6070 EITHER TOO MANY OR UNRECOVERABLE HARDWARE ERRORS ON VOLUME (VSN=vvvvvv)
Meaning
Too many hardware errors occurred, in sequence, on the same volume.
The action requested by options MRV27 has been started for
the JOB and MRV25 has been started for the volume.
These options can be found and modified in the file
message/message_resp of ROBAR-SV.
Exception: if the mount has been directly requested by MAREN,
it is always rejected with the response "N".
Additional information:
- vvvvvv: Volume Serial Number
Response
Fix the error. Contact the maintenance, if necessary.
After the error has been fixed, in certain circumstances the
volume error counter has to be reset manually by the command
/SEND-MESSAGE TO=OPERATOR,MESSAGE='<T VOLUME vvvvvv REPAIRED'
resp. INFORM-OPERATOR MSG='<T VOLUME vvvvvv REPAIRED'.
ROB6071
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB6071 DEVICE ERROR COUNTER RESET (DEV=mmmm)
Meaning
ROBAR now considers the device as repaired.
- mmmm: Device Mnemonic
ROB6072
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB6072 HARDWARE ERROR DETECTED (DEV=mmmm / TSN=tttt / VSN=vvvvvv)
Meaning
ROBAR detected a hardware error on device or volume.
Possible reason :
The mounted volume got a wrong type.
Additional information:
- mmmm : device mnemonic
- tttt : Task Serial Number
- vvvvvv: Volume Serial Number
Response
Details on the HW error are given in the preceding EXC0858
message. It is perhaps necessary to initialise the volume again.
ROB6073
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB6073 VOLUME ERROR COUNTER RESET (VSN=vvvvvv)
Meaning
ROBAR now considers the volume as repaired or new.
- vvvvvv: Volume Serial Number
ROB6074
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB6074 VOLUME INIT ONLY PERMITTED WITH MAREN (VSN=vvvvvv / TSN=tttt)
Meaning
The mounted volume can only be initialised with MAREN. It is
automatically dismounted.
Additional information:
- vvvvvv: Volume Serial Number
- tttt : Task Serial Number
Response
Try to initialise the volume by using MARENADM.
ROB6076
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB6076 NO DEVICE ACCESS PATH IS AVAILABLE, DEVICE DETACHED (DEV=mmmm)
Meaning
No path is available to access the device. Possible reason:
- no switch of device to virtual machine
Additional information:
- mmmm: device mnemonic
Response
Possible actions :
1. Switch the device to the involved virtual machine.
2. Attach the corresponding controller.
ROB6507
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB6507 VOLUME HAS A TAPE LENGTH ERROR AND IS UNLOADED (TSN=tttt / VSN=vvvvvv)
Meaning
After the device has been unloaded, the volume is put back to
its storage place. It cannot be mounted for write operation on
the specified device.
Possible reasons are:
1. An attempt to write on a TAPE-C1 or TAPE-C2 tape with a TAPE-C4
device, but this latter can only read these volume types.
2. Inversely, a TAPE-C1 or TAPE-C2 device is not able to deal
with TAPE-C4 volumes.
3. An error occurred with the medium.
Additional information:
- tttt : Task Serial Number
- vvvvvv: Volume Serial Number
Response
Change the volume definition in MAREN catalog if possible, or
eject the volume from the AML system to manage it manually, or
copy the volume on a support of appropriate type.
Contact the system administrator, if necessary.
ROB6508
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB6508 VOLUME HAS A TAPE LENGTH ERROR AND IS EJECTED (TSN=tttt / VSN=vvvvvv)
Meaning
The current tape length is too short. The volume must be removed from
the robot system because it cannot be mounted on a device managed
by the robot without a risk of damage.
Additional information:
- tttt : Task Serial Number
- vvvvvv: Volume Serial Number
Response
Replace the defective volume.
Contact the system administrator, if necessary.
ROB7005
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB7005 COMMAND SUCCESSFULLY PROCESSED (TSN=tttt)
Meaning
The ROBAR-SDF command has been successfully processed.
Additional information:
- tttt: Task Serial Number
ROB7010
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB7010 ERROR OCCURRED. COMMAND NOT PROCESSED (TSN=tttt, ERROR=ffff)
Meaning
An error occurred so that the ROBAR-SDF command could not be processed.
Additional information:
- tttt: Task Serial Number
- ffff: error code returned by the AML system
(issue a /HELP-MSG ROBffff command to get its meaning)
Response
Contact the maintenance, if necessary.
ROB7014
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB7014 VSN IS ALREADY DEFINED (TSN=tttt / VSN=vvvvvv)
Meaning
Possible reasons:
- volume already belongs to a freepool
Additional information:
- tttt : Task Serial Number
- vvvvvv: Volume Serial Number
Response
Possible actions :
- use another volume identifier to issue the command
ROB7015
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB7015 VSN OR POSITION IS ALREADY ASSIGNED (TSN=tttt / VSN=vvvvvv / POSITION=aaaaaa)
Meaning
Possible reasons:
- The volume is already defined as a foreign.
- The foreign position is already used by ROBAR or another host.
Additional information:
- tttt : Task Serial Number
- vvvvvv: Volume Serial Number
- aaaaaa: Foreign Cartridge Storage Place
Response
Possible actions :
- Use another volume identifier to issue the command.
- Use another position to issue the command.
- Make sure that the position is released by the other host (DAS,...).
ROB7016
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB7016 INCONSISTENCY DETECTED WHEN MANAGING THE FREEPOOL (TSN=tttt)
Meaning
The command could not be processed because it induces an inconsistency
in the existing definitions.
Possible reason:
- The VSN ranges overlap.
Additional information:
- tttt: Task Serial Number
ROB7017
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB7017 ERROR OCCURRED WHEN ACCESSING THE VOLUME DEFINITIONS (TSN=tttt)
Meaning
An error occurred when accessing to the volume definitions.
Possible reasons :
1. The foreign/freepool directory is locked or secured.
2. The foreign/freepool definitions are inconsistent.
3. The foreign/freepool definitions do not exist.
4. The foreign/freepool definitions are already erased.
Additional information:
- tttt: Task Serial Number
Response
Possible actions :
1. Correct the access right to the definition files.
2. Erase the existing definitions and create new ones.
3. Contact the maintenance if necessary.
ROB7018
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB7018 SYNTAX ERROR IN VSN SPECIFICATION (TSN=tttt)
Meaning
At least one given volume name is in error.
Possible reasons :
1. The VSN is over 6 characters in length.
2. The VSNs in the freepool range have different lengths.
3. The VSN range boundaries have different prefix or suffix.
4. The range part used to define the boundaries does not only
contain digits.
Additional information:
- tttt: Task Serial Number
Response
Correct the VSN definition and try again.
ROB7019
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB7019 VSN NOT KNOWN IN ROBAR_ARCHIV OR POSITION NOT KNOWN IN ROBAR_FOREIGN (TSN=tttt / VSN=vvvvvv)
Meaning
The VSN must be defined in ROBAR_ARCHIV and the POSITION in ROBAR_FOREIGN
but they are not.
Additional information:
- tttt : Task Serial Number
- vvvvvv: Volume Serial Number
Response
Define the VSN in ROBAR_ARCHIV or the POSITION in ROBAR_FOREIGN and try
the command again.
ROB7020
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB7020 VSN IS MOUNTED OR IN INCONSISTENCY STATE. REMOVAL OF ITS FOREIGN DEFINITION IS NOT ALLOWED (TSN=tttt / VSN=vvvvvv)
Meaning
The specified volume has a foreign position indicated as shared.
To keep consistent information for usage of the position by
other hosts, it is forbidden to remove its foreign definition
as long as the volume is mounted.
Additional information:
- tttt : Task Serial Number
- vvvvvv: Volume Serial Number
Response
Remove the definition when the volume is not mounted any more.
ROB7060
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB7060 VOLUME EJECTED (TSN=tttt / VSN=vvvvvv)
Meaning
The volume has been successfully ejected.
Additional information:
- tttt : Task Serial Number
- vvvvvv: Volume Serial Number
ROB7061
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB7061 VOLUME IS DEFECTIVE (VSN=vvvvvv)
Meaning
A previous BS2000 error message describes the error.
Additional information:
- vvvvvv: Volume Serial Number
ROB7062
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB7062 VOLUME WAS ALREADY EJECTED (TSN=tttt / VSN=vvvvvv)
Meaning
The volume has been previously ejected.
It is already in the I/O box. Nothing to do.
Additional information:
- tttt : Task Serial Number
- vvvvvv: Volume Serial Number
ROB7063
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB7063 WARNING: VOLUME UNKNOWN IN ROBOT DATA BASE (TSN=tttt / VSN=vvvvvv)
Meaning
The volume is unknown in the robot system data base.
Either it is already in the I/O box after an Eject Total (EJT),
or there is an inconsistency.
Nothing to do.
Additional information:
- tttt : Task Serial Number
- vvvvvv: Volume Serial Number
ROB7064
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB7064 VOLUME MOUNTED ON DEVICE. EJECT NOT POSSIBLE (TSN=tttt / VSN=vvvvvv)
Meaning
The volume is mounted on a device.
Eject is not possible. Command rejected.
Additional information:
- tttt : Task Serial Number
- vvvvvv: Volume Serial Number
Response
Enter /UNLOAD in BS2000 or KE in MANUAL menu.
ROB7065
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB7065 EJECT NOT PROCESSED (TSN=tttt / VSN=vvvvvv)
Meaning
The volume ejection could not be performed. Possible reasons :
- The output box is full.
- The volume is unknown or already ejected.
- An unknown AML system error occurred during volume ejection.
- In the config file of ROBAR-SV the parameter robot_output_area
- has a wrong value.
Additional information:
- tttt : Task Serial Number
- vvvvvv: Volume Serial Number
ROB7066
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB7066 OUTPUT BOX IS FULL
Meaning
Eject command cannot be processed.
Response
Empty the output box and try the command again.
ROB7070
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB7070 INSERT STARTED (TSN=tttt)
Meaning
The cartridge insertion will be processed asynchronously.
Additional information:
- tttt: Task Serial Number
ROB8010
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB8010 EMERGENCY UNLOAD WAS UNSUCCESSFUL (DEV=mmmm)
Meaning
Additional information:
- mmmm: device mnemonic
ROB8015
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB8015 EMERGENCY UNLOAD ACTIVATED (DEV=mmmm), PLEASE WAIT
Meaning
Due to the running context and possibly previous hardware errors,
ROBAR decides to make the device empty. Please wait.
Additional information:
- mmmm: device mnemonic
ROB8020
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB8020 EMERGENCY UNLOAD WAS SUCCESSFUL
ROB9000
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB9000 TAPE CARTRIDGE HAS DMS WRITE PROTECTION (TSN=tttt / VSN=vvvvvv)
Meaning
Additional information:
- tttt : Task Serial Number
- vvvvvv: Volume Serial Number
Response
Contact the system administrator, if necessary.
ROB9003
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB9003 EXPORT-COMMAND RESUMED
Meaning
The previous export command was interrupted, but it is correctly
resumed now.
ROB9004
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB9004 EXPORT-COMMAND CANNOT BE RESUMED
Meaning
Due to an AML system error, the export command cannot be resumed.
Response
Possible actions:
1. Make the AML system ready for work.
2. Make the output box empty.
ROB9600
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB9600 ROBAR COUNTS A GRAVE ERROR ON DEVICE mmmm
Meaning
ROBAR counted a grave error on the device.
When the number of errors hits the limit given in the
ROBAR-SV configuration file (device_error_limit=),
special actions are started for the BS2000 job and the device.
The action on the BS2000 job is defined in the MRV26 option of the
file message/message_resp of ROBAR-SV.
The action on the device is defined in the MRV24 option of the file
message/message_resp of ROBAR-SV.
The default value for device_error_limit is 3.
The default action on BS2000 job is to move it on another device.
The default action on the device is to detach it.
Exception: if the mount has been directly requested by MAREN,
it is always rejected with the response "N".
If the next job on the device is error free, the error counter
will be decreased.
Additional information:
- mmmm: device mnemonic
Response
Possible actions :
1. Analyse the error origin by a conslog analysis.
2. Contact the maintenance if necessary.
ROB9601
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB9601 ROBAR DEDUCTS A GRAVE ERROR FOR DEVICE mmmm
Meaning
Robar counted grave errors in sequence on the device. Since the last
operation was successfully processed, the error counter has been
decreased.
Additional information:
- mmmm: device mnemonic
ROB9602
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB9602 ROBAR COUNTS A GRAVE ERROR ON VOLUME vvvvvv
Meaning
ROBAR counted a grave error on the volume.
When the number of errors reaches the limit given in the
ROBAR-SV configuration file (volume_error_limit=),
special actions are started for the BS2000 job and the volume.
The action on BS2000 job is defined in the MRV27 option of the
file message/message_resp of ROBAR-SV.
The action on volume is defined in the MRV25 option of the file
message/message_resp of ROBAR-SV.
The default value for volume_error_limit is 3.
The default action on BS2000 job is to cancel it.
The default action on the device is to eject it.
Exception: if the mount has been directly requested by MAREN,
it is always rejected with the response "N".
If the next job on the volume is error free, the error counter
will be decreased.
Additional information:
- vvvvvv: Volume Serial Number
Response
Possible actions :
1. Analyse the error origin by a conslog analysis
2. Contact the maintenance if necessary
ROB9603
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB9603 ROBAR DEDUCTS A GRAVE ERROR FOR VOLUME vvvvvv
Meaning
Robar counted grave errors in sequence on the VSN. Since the last
operation was successfully processed, the error counter has been
decreased.
Additional information:
- vvvvvv: Volume Serial Number
ROB9800
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB9800 CENTRICSTOR IS UNABLE TO EXECUTE COMMAND
Response
A problem occurred in CentricStor. Please contact your CentricStor
system engineer.
ROB9801
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB9801 COMMAND IS NOT PERMITTED
Meaning
A command has been requested to a CentricStor configuration
but either the ROBAR RULE FILE is not the one dedicated to such a
CentricStor configuration or the MAREN catalogue is configured
for a location with type "ROBAR-2" but should not.
The command cannot be executed and is negatively acknowleged.
Response
Either install the ROBAR RULE FILE for a CentricStor
configuration or correct your location attribute in MAREN.
ROB9802
Destination: CONSOLE Routing code: T Weight: 99
Warranty : NO
ROB9802 A PROBLEM OCCURRED IN CENTRICSTOR. LOCATION : (&00)
Meaning
(&00): LOCATION of the CentricStor
Response
Please check CentricStor console for detailed information.
ROB9803
Destination: USER-TASK Routing code: Weight:
Warranty : NO
ROB9803 COMMAND NOT PERMITTED: FOREIGN VOLUMES AND FREEPOOLS NOT SUPPORTED
Meaning
Foreign volumes and freepools are not supported in ROBAR-SV for
SCSI interface.