Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : NO
NKD0001 SYNTAX ERROR IN '(&00)' COMMAND. COMMAND NOT PROCESSED
Meaning
(&00): /SHOW command of the nucleus device management.
Response
Enter the correct command.
NKD0002
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0002 REQUESTED INFORMATION COULD NOT BE OBTAINED. RETRY COMMAND LATER
Meaning
The current system state prevented the processing of the command.
NKD0005
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0005 WARNING: REQUESTED INFORMATION NOT COMPLETE
Meaning
The requested information could be obtained and displayed only partially.
Possible reasons:
1. Some of the HW units that were selected do not exist in the system.
2. In the command /SHOW-DISK-STATUS resp. /SHOW-TAPE-STATUS only
only disk resp. tape units are processed.
3. The selected additional operands (e.g. INFORMATION) do not allow
to issue information about some HW units.
Response
Check the input.
NKD0006
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0006 SOFTWARE ERROR IN PROCEDURE '(&00)'. PROCESSING CONTINUES
Meaning
Inconsistency in system module.
(&00): procedure of the nucleus device management information
facility (NKD).
Response
Contact the system administrator.
NKD0007
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0007 USER IDENTIFICATION CANNOT OBTAIN THIS INFORMATION. '(&00)' COMMAND NOT PROCESSED
Meaning
The command is not permitted for the user ID.
(&00): /SHOW command of the nucleus device management.
NKD0009
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0009 WARNING: (&00) MONITOR TEMPORARILY NOT AVAILABLE. INFORMATION MAY NOT BE COMPLETE
NKD0010
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0010 (&00) MONITOR TEMPORARILY NOT AVAILABLE. RETRY '(&01)' COMMAND LATER
NKD0011
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0011 USER ID CANNOT OBTAIN INFORMATION ON TSN (&00). COMMAND NOT PROCESSED
Meaning
The user task and the TSN (&00) have different user IDs.
Response
Correct the command.
NKD0012
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : NO
NKD0012 NO INFORMATION EXISTS FOR SPECIFIED DEVICE-RANGE
NKD0013
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0013 COMMAND '(&00)' WITHOUT EXPLICIT PARAMETERS NOT ALLOWED.COMMAND NOT PROCESSED
Response
Use the selection parameters or '(&00)' TYPE=ALL
to obtain information about all devices.
NKD0014
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0014 NO ALLOCATION EXISTS FOR THE TASK WITH TSN (&00). COMMAND NOT PROCESSED
NKD0016
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0016 NO RELEVANT INFORMATION EXISTS FOR 'TSN = (&00)' AND 'INFORMATION = (&01)'. COMMAND NOT PROCESSED
Meaning
(&00),(&01): operand values of the specified /SHOW command.
NKD0018
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0018 MONJV NOT FOUND. JVS RETURN CODE: '(&00)'. ERROR INF IN SYSTEM MODE: /HELP JVS(&00)
Meaning
(&00): result of an unsuccessful search for the specified MONJV by the
JV management.
Note: '(&00)' corresponds to 'JVS(&00)'.
For more detailed information on the JVS return code enter /HELP JVS(&00)
or see the manual 'System Messages'.
NKD0019
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0019 FOUND JOB VARIABLE IS NOT AN ACTIVE MONJV
Meaning
The entered string is the name of a job variable, but its contents does
not denote an active MONJV.
Response
Check the command as well as the JV state and the JV contents.
NKD0021
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0021 NO INFORMATION EXISTS FOR 'TYPE = (&00)' AND 'ATTRIBUTE = (&01)'. COMMAND NOT PROCESSED
Meaning
(&00),(&01): operand values of the specified /SHOW command.
NKD0023
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0023 NO INFORMATION EXISTS FOR UNIT = '(&00)'. COMMAND NOT PROCESSED
Meaning
(&00): mnemonic of the requested unit class (list possible).
NKD0024
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0024 NO INFORMATION EXISTS FOR 'CLASS = (&00)' AND 'ATTRIBUTE = (&01)'. COMMAND NOT PROCESSED
Meaning
(&00),(&01): operand values of the specified /SHOW command.
NKD0025
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0025 NO RELEVANT INFORMATION EXISTS FOR UNIT = '(&00)' AND 'INFORMATION = (&01)'. COMMAND NOT PROCESSED
Meaning
(&00),(&01): operand values of the specified /SHOW command.
NKD0026
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0026 SUBSYSTEM JVS NOT LOADED.COMMAND CANNOT BE PROCESSED
Meaning
The command was issued with parameter MONJV (Monitor Job Variable).
The JVS (Job Variable Subsystem) is currently not loaded.
Therefore the command cannot be processed.
NKD0027
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0027 NO INFORMATION EXISTS FOR UNIT = '(&00)'
Meaning
NO INFORMATION CONCERNING THE UNITS '(&00)' EXISTS OR THE USER IS NOT
PRIVILEGED TO GET RELEVANT INFORMATION.
NKD0028
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0028 WARNING : NO RELEVANT INFORMATION EXISTS FOR UNIT = '(&00)' AND INFORMATION = '(&01)'
Meaning
THE UNITS '(&00)' ARE NOT GENERATED IN THE SYSTEM OR THE USER IS NOT
PRIVILEGED TO OBTAIN INFORMATION '(&01)'.
Response
NO RESPONSE POSSIBLE. TRY OTHER MNEMONICS.
NKD0030
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0030 OPERAND CHANGED TO 'INFORMATION = (&00)'. PROCESSING CONTINUES
Meaning
In the specified /SHOW command only INFORMATION = (&00) is permissible as
an operand value.
NKD0031
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0031 NO INFORMATION EXISTS FOR 'VOLUME = (&00)'. COMMAND NOT PROCESSED
Meaning
(&00): operand value of the specified /SHOW command.
NKD0032
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0032 NO RELEVANT INFORMATION EXISTS FOR 'ATTRIBUTE = (&00)'. COMMAND NOT PROCESSED
Meaning
(&00): operand value of the specified /SHOW command.
NKD0033
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0033 NO RELEVANT INFORMATION EXISTS FOR 'VOLUME = (&00)' AND 'INFORMATION = (&01)'. COMMAND NOT PROCESSED
Meaning
(&00),(&01): operand values of the specified /SHOW command.
NKD0034
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0034 WARNING : NO RELEVANT INFORMATION EXISTS FOR 'VOLUME = (&00)'
NKD0035
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0035 WARNING : NO RELEVANT INFORMATION EXISTS FOR 'VOLUME = (&00)' AND 'INFORMATION = (&01)'
NKD0036
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0036 NO INFORMATION EXISTS FOR 'LOCATION = (&00)'. COMMAND NOT PROCESSED
Meaning
(&00): operand value of the specified /SHOW command.
NKD0037
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0037 NO INFORMATION EXISTS FOR ROUTING-CODE = '(&00)'
Meaning
THERE IS NO LOCATION WITH THE GIVEN ROUTING-CODE
NKD0038
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0038 NO DEVICE OF TYPE = (&00) HAS BEEN ASSIGNED TO A LOCATION
Meaning
Because no device of type (&00) has been assigned to a location the
command SHOW-DEVICE-STATUS with INFORMATION = LOCATION delivers no
output.
Response
The user may try SHOW-DEVICE-STATUS with other Informationparameters
(STANDARD/ALL/SUMMARY/TYPTASK) to get information relevant to type (&00)
NKD0039
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0039 NO INFORMATION EXISTS FOR LOCATION = '(&00)'
Meaning
THE LOCATIONS '(&00)' DO NOT EXIST IN THE SYSTEM.
Response
ENTER ' SH-DEV-D ' WITHOUT PARAMETERS TO GET A DISPLAY OF ALL LOCATIONS.
NKD0040
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0040 NO SECURE QUEUE EXISTS. COMMAND NOT PROCESSED
Meaning
No task is waiting for its /SECURE resp. /SECURE-RESOURCE-ALLOCATION
command to be processed.
NKD0041
Destination: USER-TASK, CONSOLE Routing code: E Weight: 70
Warranty : YES
NKD0041 NO COLLECTOR TASK EXISTS. COMMAND NOT PROCESSED
Meaning
Either RESOURCE-COLLECTION is not set or no task has been created as a
collector task. Use INFORMATION=COLLECT to obtain further information.