Destination: USER-TASK Routing code: Weight:
Warranty : NO
HWM0000 HMW - Messages of the X2000 package SMAWLhwm ( Hardware Monitor )
Meaning
The X2000 package SMAWLhwm monitors tape devices of the type
9084-110 und 9084-221.
The devices to be monitored must be registered in the file
/etc/host.
The executing cron job
<BASEDIR>/SMAWLhwm/check_dev_status.sh
can be adapted.
The file
/etc/opt/SMAW/X2000/SMAWLhwm.conf
can be supplied e.g. with email addresses.
See the manual
MTC Charger 9084-110 and 9084-221F / Operation under BS2000/OSD
and the documents mentioned there.
HWM0001
Destination: USER-TASK Routing code: Weight:
Warranty : NO
HWM0001 No entry for device type 9084-110/221 in /etc/hosts
Meaning
There is no entry for a tape device of type 9084-110/221 in /etc/hosts.
( Message displayed by the X2000 package SMAWLhwm ( Hardware Monitor ). )
Response
Configure the devices to be monitored.
Format of an entry in /etc/hosts:
< IP-Address> <Name> # 9084-110 or 9084-221
If no tape device shall be monitored, deactivate the cron job
<BASEDIR>/SMAWLhwm/check_dev_status.sh.
HWM0101
Destination: USER-TASK Routing code: Weight:
Warranty : NO
HWM0101 Device (&00): Not reachable
Meaning
The specified device ist not reachable by the monitor.
( Message displayed by the X2000 package SMAWLhwm ( Hardware Monitor ). )
Response
Check the status of the device:
-> Failed or switched off or taken out ?
-> Not connected to the LAN / connection interrupted / wrong address ?
If the device shall no longer be monitored, please remove the entry or
the tag 9084 from the /etc/hosts file.
HWM0111
Destination: USER-TASK Routing code: Weight:
Warranty : NO
HWM0111 Device (&00): Only (&01) cleaning cycles left
Meaning
With the cleaning tape of the specified device just
a few cleaning cycles can be executed.
( Message displayed by the X2000 package SMAWLhwm ( Hardware Monitor ). )
Response
Please order a new cleaning tape in due time and
insert it into the device, when RemainingCleanCount = 0.
Reinitialize the value of RemainingCleanCount. This value can
be found in the description of the used cleaning tape.
HWM0112
Destination: USER-TASK Routing code: Weight:
Warranty : NO
HWM0112 Device (&00): Option AutoClean not activated
Meaning
The AutoClean option has not been activated for the specified device.
Consequence: No automatic cleaning can be executed.
( Message displayed by the X2000 package SMAWLhwm ( Hardware Monitor ). )
Response
To enable automatic cleaning please set the AutoClean option
using the operator panel or the web-interface.
HWM0113
Destination: USER-TASK Routing code: Weight:
Warranty : NO
HWM0113 Device (&00): Option CleanSlot not activated
Meaning
The CleanSlot option ( marks the slot as slot for the cleaning tape )
for the specified device has not been activated.
Consequence: No cleaning can be executed.
( Message displayed by the X2000 package SMAWLhwm ( Hardware Monitor ). )
Response
To enable cleaning please set the CleanSlot option using the
operator panel or the web-interface.
HWM0114
Destination: USER-TASK Routing code: Weight:
Warranty : NO
HWM0114 Device (&00): CleanSlot index ( value (&01) ) incorrectly configured
Meaning
A wrong slot has been chosen to be the slot for the cleaning tape.
Consequence: No cleaning can be executed.
( Message displayed by the X2000 package SMAWLhwm ( Hardware Monitor ). )
Response
The correct setting is:
9084-110 --> Slot 10
9084-221 --> Slot 21
HWM0115
Destination: USER-TASK Routing code: Weight:
Warranty : NO
HWM0115 Device (&00): Clean slot (&01) empty or incorrectly supplied
Meaning
There is no (valid) cleaning tape in the cleaning slot.
Consequence: No cleaning can be executed.
( Message displayed by the X2000 package SMAWLhwm ( Hardware Monitor ). )
Response
Please supply the cleaning slot with a correctly labeled cleaning tape.
HWM0121
Destination: USER-TASK Routing code: Weight:
Warranty : NO
HWM0121 Device (&00): Error state (&01)
Meaning
The tape library notifies the specified error.
( Message displayed by the X2000 package SMAWLhwm ( Hardware Monitor ). )
Response
Please check the state of the device.
For this, use also the documentation given in the manual
MTC Charger 9084-110 and 9084-221F / Operation under BS2000/OSD.
HWM0131
Destination: USER-TASK Routing code: Weight:
Warranty : NO
HWM0131 Device (&00): Erroneous state of power supply #(&01)
Meaning
The tape library notifies an error concerning the power supply.
( Message displayed by the X2000 package SMAWLhwm ( Hardware Monitor ). )
Response
Please check the state of the device.
For this, use also the documentation given in the manual
MTC Charger 9084-110 and 9084-221F / Operation under BS2000/OSD.
HWM0141
Destination: USER-TASK Routing code: Weight:
Warranty : NO
HWM0141 Device (&00): Erroneous state of fan #(&01)
Meaning
The tape library notifies an error concerning a fan.
( Message displayed by the X2000 package SMAWLhwm ( Hardware Monitor ). )
Response
Please check the state of the device.
For this, use also the documentation given in the manual
MTC Charger 9084-110 and 9084-221F / Operation under BS2000/OSD.