HSV0001

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0001 ERROR DURING SVP FUNCTION DIAGNOSE MSSFCALL OBTAIN SYSTEM INFORMATION

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  0010  OK, information delivered.
  06F0  The SVP function is not executable on this configuration.
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.

HSV0002

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0002 ERROR DURING THE SVP FUNCTION DIAGNOSE MSSFCALL OBTAIN SIDE INFORMATION

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  0010  OK, information delivered.
  0110  OK, Information delivered. The SIDE belongs to another
        configuration.
  06F0  The SVP function is not executable on this configuration.
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.

HSV0003

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0003 ERROR DURING SVP FUNCTION DIAGNOSE MSSFCALL VARY SIDE ONLINE

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  0020  The SIDE was switched to "online".
  0120  The SIDE was already "online".
  0040  Hardware error.
  03F0  Wrong SIDE Identifier specified.
  04F0  The SIDE belongs to another configuration.
  05F0  The SIDE belongs to another configuration.
  06F0  The SVP function is not executable on this configuration.
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.

HSV0004

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0004 ERROR DURING SVP FUNCTION DIAGNOSE MSSFCALL VARY SIDE OFFLINE

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  0020  The SIDE was switched to "offline".
  0120  The SIDE was already "offline".
  0040  Hardware error.
  0240  Error in the SVP.
  03F0  Wrong SIDE Identifier specified.
  04F0  The SIDE belongs to another configuration.
  05F0  The SIDE belongs to another configuration.
  06F0  The SVP function is not executable on this configuration.
  07F0  Not all elements are "offline".
  08F0  The SVP function is not executable on this configuration.
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.

HSV0005

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0005 ERROR DURING SVP FUNCTION OBTAIN CHANNEL PATH INFORMATION

Meaning

HSV0006

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0006 ERROR DURING SVP FUNCTION VARY CHANNEL PATH ONLINE

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  0020  The CHANNEL PATH was switched to "online".
  0120  The CHANNEL PATH was already "online".
  0040  Hardware error.
  0140  The IOSIDE was "busy" and could not execute the function.
  0240  Error in the SVP.
  03F0  Wrong CHANNEL PATH Identifier specified.
  04F0  The CHANNEL PATH belongs to another configuration.
  05F0  The CHANNEL PATH belongs to another configuration.
  06F0  The SVP function is not executable on this configuration.
  08F0  Not executable on the configuration.
  0DF0  The IOSIDE is not assigned.
  0400  Hardware error.
  0401  The CHANNEL PATH is not installed or already "online"
        or switching online is disabled.
  0402  The CHANNEL CONTROLLER is not "online".
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.

HSV0007

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0007 ERROR DURING SVP FUNCTION CHANNEL PATH OFFLINE

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  0020  The CHANNEL PATH was switched to "offline".
  0120  The CHANNEL PATH was already "offline".
  0040  Hardware error.
  0140  The IOSIDE was "busy" and could not execute the function.
  0240  Error in the SVP.
  03F0  Wrong CHANNEL PATH Identifier specified.
  04F0  The CHANNEL PATH belongs to another configuration.
  05F0  The CHANNEL PATH belongs to another configuration.
  06F0  The SVP function is not executable on this configuration.
  08F0  Not executable on the configuration.
  0DF0  The IOSIDE is not assigned.
  0400  Hardware error.
  0401  The CHANNEL PATH is not installed or switching offline is
        disabled.
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.

HSV0008

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0008 ERROR DURING SVP FUNCTION DIAGNOSE MSSFCALL OBTAIN IOSIDE INFORMATION

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  0010  OK, information delivered. The IOSIDE is "online".
  0110  OK, information delivered. The IOSIDE is "offline".
  0410  OK, information delivered. The IOSIDE is the only IOSIDE.
  0040  Hardware error.
  0140  The IOSIDE was "busy" and could not execute the function.
  03F0  Wrong IOSIDE Identifier specified.
  04F0  The IOSIDE belongs to another configuration.
  05F0  The IOSIDE belongs to another configuration.
  06F0  The SVP function is not executable on this configuration.
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.

HSV0009

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0009 ERROR DURING SVP FUNCTION DIAGNOSE MSSFCALL VARY IOSIDE ONLINE

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  0020  The IOSIDE was switched to "online".
  0120  The IOSIDE was already "online".
  0040  Hardware error.
  0140  The IOSIDE was "busy" and could not execute the function.
  03F0  Wrong IOSIDE Identifier specified.
  04F0  The IOSIDE belongs to another configuration.
  05F0  The IOSIDE belongs to another configuration.
  06F0  The SVP function is not executable on this configuration.
  0DF0  The IOSIDE is not assigned.
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.

HSV0010

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0010 ERROR DURING SVP FUNCTION DIAGNOSE MSSFCALL VARY IOSIDE OFFLINE

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  0020  The IOSIDE was switched to "offline".
  0120  The IOSIDE was already "offline".
  0040  Hardware error.
  0140  The IOSIDE was "busy" and could not execute the function.
  03F0  Wrong IOSIDE Identifier specified.
  04F0  The IOSIDE belongs to another configuration.
  05F0  The IOSIDE belongs to another configuration.
  06F0  The SVP function is not executable on this configuration.
  07F0  Not all CHANNEL PATHS are "offline".
  08F0  The SVP function is not executable on this configuration.
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.

HSV0011

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0011 ERROR DURING SVP FUNCTION DIAGNOSE MSSFCALL OBTAIN STORAGE ELEMENT INFORMATION

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  0010  OK, information delivered.
  0110  OK, information delivered. The STORAGE ELEMENT is "offline".
  0040  Hardware error.
  03F0  Wrong STORAGE ELEMENT Identifier specified.
  04F0  The STORAGE ELEMENT belongs to another configuration.
  05F0  The STORAGE ELEMENT belongs to another configuration.
  06F0  The SVP function is not executable on this configuration.
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.

HSV0012

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0012 ERROR DURING SVP FUNCTION DIAGNOSE MSSFCALL OBTAIN HIGHEST STORAGE ELEMENT ID

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  0010  OK, information delivered.
  0040  Hardware error.
  06F0  The SVP function is not executable on this configuration.
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.

HSV0013

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0013 ERROR DURING SVP FUNCTION DIAGNOSE MSSFCALL VARY STORAGE ELEMENT ONLINE

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  0020  The STORAGE ELEMENT was switched to "online".
  0120  The STORAGE ELEMENT was already "online".
  0040  Hardware error.
  03F0  Wrong STORAGE ELEMENT Identifier specified.
  04F0  The STORAGE ELEMENT belongs to another configuration.
  05F0  The STORAGE ELEMENT belongs to another configuration.
  06F0  The SVP function is not executable on this configuration.
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.

HSV0014

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0014 ERROR DURING SVP FUNCTION DIAGNOSE MSSFCALL VARY STORAGE ELEMENT OFFLINE

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  0020  The STORAGE ELEMENT was switched to "offline".
  0120  The STORAGE ELEMENT was already "offline".
  0040  Hardware error.
  03F0  Wrong STORAGE ELEMENT Identifier specified.
  04F0  The STORAGE ELEMENT belongs to another configuration.
  05F0  The STORAGE ELEMENT belongs to another configuration.
  06F0  The SVP function is not executable on this configuration.
  09F0  Invalid address or address range specified.
  0AF0  Inaccessible storage specified or address relocation needed
        but not specified.
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.

HSV0015

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0015 ERROR DURING SVP FUNCTION DIAGNOSE MSSFCALL VARY STORAGE PHYSICALLY ONLINE

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  0020  The storage was switched to "online".
  0120  The storage was already "online".
  0040  Hardware error.
  04F0  The storage belongs to another configuration.
  05F0  The storage belongs to another configuration.
  06F0  The SVP function is not executable on this configuration.
  09F0  Invalid address or address range specified.
  0CF0  All storage is currently assigned.
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.

HSV0016

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0016 ERROR DURING SVP FUNCTION DIAGNOSE MSSFCALL VARY STORAGE PHYSICALLY OFFLINE

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  0020  The storage was switched to "offline".
  0120  The storage was already "offline".
  0040  Hardware error.
  04F0  The storage belongs to another configuration.
  05F0  The storage belongs to another configuration.
  06F0  The SVP function is not executable on this configuration.
  09F0  Invalid address or address range specified.
  0AF0  Inaccessible storage specified.
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.

HSV0017

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0017 ERROR DURING SVP FUNCTION DIAGNOSE MSSFCALL READ IOCDS

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  xx20  The requested function was completed.
        xx returns further information (logical OR):
        80 The IOCDS was open for write. The returned data may be
           invalid.
        40 The IOCDS is the active IOCDS.
        20 The IOCDS was updated since the last IMPL.
  0040  Hardware error.
  4040  Error during open or read of the IOCDS.
  40F0  The IOCDS block number is invalid.
  41F0  The IOCDS is not open.
  42F0  Invalid IOCDS specified.
  50F0  The IOCDS end was exceeded.
  06F0  The SVP function is not executable on this configuration.
  PARE  Parameter error.
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.

HSV0018

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0018 ERROR DURING SVP FUNCTION DIAGNOSE MSSFCALL WRITE IOCDS

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  xx20  The requested function was completed.
        xx returns further information (logical OR):
        80 The IOCDS was already open for write.
        40 The IOCDS is the active IOCDS.
        20 The IOCDS was updated since the last IMPL.
  0040  Hardware error.
  4040  Error during open or write of the IOCDS.
  40F0  The IOCDS block number is invalid.
  41F0  The IOCDS is not open.
  42F0  Invalid IOCDS specified.
  50F0  The IOCDS end was exceeded.
  06F0  The SVP function is not executable on this configuration.
  PARE  Parameter error.
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.

HSV0019

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0019 ERROR DURING SVP FUNCTION DIAGNOSE MSSFCALL READ ACTIVE IOCDS

Meaning

HSV0020

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0020 ERROR DURING THE SVP FUNCTION DIAGNOSE WRITE CONSOLE.

Meaning

HSV0021

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0021 ERROR DURING THE SVP FUNCTION DIAGNOSE HARDWARE SUPPORT FUNCTION READ CORER INFORMATION

Meaning

HSV0022

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0022 ERROR DURING THE SVP FUNCTION DIAGNOSE HARDWARE SUPPORT FUNCTION CLEAR CORER IN MEMORY UNIT

Meaning

HSV0023

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0023 ERROR DURING SVP FUNCTION READ IORSF

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  FFxx  Hardware error.
  0001  The IORSF end was exceeded.
  0300  Command not supported.
  1101  The indicated SVP cannot operate.
  1102  The IORSF number is too large.
  1103  The start sector number exceeded the maximum sector of the
        IORSF file.
  3000  IORSF file access error.
  3500  The buffer busy condition was detected.
  3600  The IO-configuration is not supported or a logical error
        was detected.

  xx20  The requested function was completed.
        xx returns further information (logical OR):
        80 The IORSF was open for write. The returned data may be
           invalid.
        40 The IORSF is the active IORSF.
        20 The IORSF was updated since the last IMPL.
  0040  Hardware error.
  4040  Error during open or read of the IORSF.
  40F0  The IORSF block number is invalid.
  41F0  The IORSF is not open.
  42F0  Invalid IORSF specified.
  50F0  The IORSF end was exceeded.
  06F0  The SVP function is not executable on this configuration.

  PARE  Parameter error.
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.

HSV0024

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0024 ERROR DURING SVP FUNCTION WRITE IORSF

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  FFxx  Hardware error.
  0001  The IORSF end was exceeded.
  0300  Command not supported.
  1101  The indicated SVP cannot operate.
  1102  The IORSF number is too large.
  1103  The start sector number exceeded the maximum sector of the
        IORSF file.
  3000  IORSF file access error.
  3100  Write-open operation for IORSF failed.
  3101  Write-close operation for IORSF failed.
  3200  The IORSF is already in write-open status.
  3300  The IORSF is not in write-open status.
  3400  The IORSF is write-protected.
  3500  The buffer busy condition was detected.
  3600  The IO-configuration is not supported or a logical error
        was detected.

  xx20  The requested function was completed.
        xx returns further information (logical OR):
        80 The IORSF was already open for write.
        40 The IORSF is the active IORSF.
        20 The IORSF was updated since the last IMPL.
  0040  Hardware error.
  4040  Error during open or write of the IORSF.
  40F0  The IORSF block number is invalid.
  41F0  The IORSF is not open.
  42F0  Invalid IORSF specified.
  50F0  The IORSF end was exceeded.
  06F0  The SVP function is not executable on this configuration.

  PARE  Parameter error.
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.

HSV0025

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0025 ERROR DURING SVP FUNCTION READ ACTIVE IORSF

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  FFxx  Hardware error.
  0001  The IORSF end was exceeded.
  1103  The start sector number exceeded the maximum sector of the
        IORSF file.
  3000  IORSF file access error.

  xx20  The requested function was completed.
        xx returns further information (logical OR):
        80 The IORSF was open for write. The returned data may be
           invalid.
        40 The IORSF is the active IORSF.
        20 The IORSF was updated since the last IMPL.
  0040  Hardware error.
  4040  Error during open or read of the IORSF.
  40F0  The IORSF block number is invalid.
  41F0  The IORSF is not open.
  42F0  Invalid IORSF specified.
  50F0  The IORSF end was exceeded.
  06F0  The SVP function is not executable on this configuration.

  PARE  Parameter error.
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.

HSV0026

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0026 ERROR DURING THE SVP FUNCTION GET GLOBAL CONFIGURATION

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  0010  OK, information delivered.
  0110  Information may not be up to date.
  E1F0  The GSU is in power off state.
  E2F0  The GSU is offline.
  E3F0  The GSU is assigned to another GCMP.
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.
  GERR  The DIAGNOSE instruction could not be executed because
        of a global error.

HSV0027

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0027 ERROR DURING THE SVP FUNCTION GET GSU INFORMATION

Meaning

HSV0028

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0028 ERROR DURING THE SVP FUNCTION GET GSU FAILURE INDICATION

Meaning

HSV0029

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0029 ERROR DURING THE SVP FUNCTION RESET GSU FAILURE INDICATION

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  0020  The call was executed.
  E0F0  The caller has no authorization for this function.
  E1F0  The GSU is in power off state.
  E2F0  The GSU is offline.
  E3F0  The GSU is assigned to another GCMP.
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.
  GERR  The DIAGNOSE instruction could not be executed because
        of a global error.

HSV0030

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0030 ERROR DURING THE SVP FUNCTION READ HARDWARE STORAGE AREA

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  0020  OK, information delivered.
  0040  Hardware error.
  4040  Error during open or read of the HSA.
  41F0  The HSA-file is not open.
  50F0  The end of HSA-file was exceeded.
  06F0  The SVP function is not executable on this configuration.

  PARE  Parameter error.
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.

HSV0031

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0031 ERROR DURING THE SVP FUNCTION MODIFY ACCESS BITS

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  0010  The call was executed.
  0301  The caller has no authorization for this function.
  1101  Number of protection blocks too large.
  E0F0  The caller has no authorization for this function.
  E1F0  The GSU is in power off state.
  E2F0  The GSU is offline.
  E3F0  The GSU is assigned to another GCMP.
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.
  GERR  The DIAGNOSE instruction could not be executed because
        of a global error.

HSV0032

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0032 ERROR DURING THE SVP FUNCTION GET GLOBAL CONNECTION

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.
  GERR  The DIAGNOSE instruction could not be executed because
        of a global error.

HSV0033

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0033 ERROR DURING THE SVP FUNCTION MODIFY GLOBAL CONNECTION

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  11F0  The SSU could not connected in guestsystem because
        SSU is not assigned to guestsystem.
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.
  GERR  The DIAGNOSE instruction could not be executed because
        of a global error.

HSV0041

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0041 ERROR DURING THE SVP FUNCTION GET IPL DEVICE LIST

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  GERR  The DIAGNOSE instruction could not be executed because
        of a global error.

HSV0042

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0042 ERROR DURING THE SVP FUNCTION MODIFY IPL DEVICE LIST

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  GERR  The DIAGNOSE instruction could not be executed because
        of a global error.

HSV0043

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0043 ERROR DURING THE SVP FUNCTION CONNECT SSU

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  11F0  The SSU could not be connected in guestsystem because
        SSU is not assigned to guestsystem.
  1111  The SSU could not be connected because SSU is not in correct
        state (neither offline nor operational).
  0401  The SSU could not be connected because SSU is not available
        (maybe Power Off).
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.
  GERR  The DIAGNOSE instruction could not be executed because
        of a global error.

HSV0044

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0044 ERROR DURING THE SVP FUNCTION DISCONNECT SSU

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  PARE  The given SSU-number is wrong.
  GERR  The DIAGNOSE instruction could not be executed because
        of a global error.

HSV0045

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0045 ERROR DURING THE SVP FUNCTION CONNECT SCMP CORE

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  11F0  A SSU could not connected in guestsystem because
        SSU is not assigned to guestsystem.
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  GERR  The DIAGNOSE instruction could not be executed because
        of a global error.

HSV0046

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0046 ERROR DURING THE SVP FUNCTION CONNECT LOCAL CLUSTER

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  GERR  The DIAGNOSE instruction could not be executed because
        of a global error.

HSV0047

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0047 ERROR DURING THE SVP FUNCTION DISCONNECT CLUSTER

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  GERR  The DIAGNOSE instruction could not be executed because
        of a global error.

HSV0050

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0050 ERROR DURING THE SVP FUNCTION DIAGNOSE SDAP READ IO-UNIT FROM IORSF

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  FFxx  Hardware error.
  0300  Command not supported.
  0301  The caller has no authorization for this function.
  1104  The specified unit type is unknown.
  1105  The specified I/O unit does not exist in IORSF.
  BUSY  The DIAGNOSE instruction was completed with condition code 1
        or 2.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.

HSV0051

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0051 ERROR DURING THE SVP FUNCTION DIAGNOSE SDAP ADD IO-UNIT TO IORSF

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  FFxx  Hardware error.
  0300  Command not supported.
  0301  The caller has no authorization for this function.
  0421  Insufficient hardware space to store control information.
  1103  No empty area to store specified I/O unit.
  1104  The specified unit type is unknown.
  1105  The specified I/O unit does not exist or already exist.
  1106  Effective byte length is wrong.
  1107  No unit to which specified i/0 unit can be connected.
  1108  Condition for replacing or adding an I/O unit is not met.
  1109  Replacement code or unit type not supported by hardware.
  BUSY  The DIAGNOSE instruction was completed with condition code 1
        or 2.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.

HSV0052

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0052 ERROR DURING THE SVP FUNCTION DIAGNOSE SDAP DELETE IO-UNIT FROM IORSF

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  FFxx  Hardware error.
  0300  Command not supported.
  0301  The caller has no authorization for this function.
  0421  Insufficient hardware space to store control information.
  1103  No empty area to store specified I/O unit.
  1104  The specified unit type is unknown.
  1105  The specified I/O unit does not exist.
  1106  Effective byte length is wrong.
  1107  A lower-level unit is connected to specified I/O unit.
  1108  Condition for replacing or deleting an I/O unit is not met.
  1109  Replacement code or unit type not supported by hardware.
  BUSY  The DIAGNOSE instruction was completed with condition code 1
        or 2.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  TOUT  The DIAGNOSE instruction was not terminated with a service
        signal interrupt during the waiting time.

HSV0056

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0056 ERROR DURING THE SVP FUNCTION DIAGNOSE SDAP VARY SSU ONLINE

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  GERR  The DIAGNOSE instruction could not be executed because
        of a global error.

HSV0057

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0057 ERROR DURING THE SVP FUNCTION DIAGNOSE SDAP VARY SSU OFFLINE

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  GERR  The DIAGNOSE instruction could not be executed because
        of a global error.

HSV0058

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0058 ERROR DURING THE SVP FUNCTION DIAGNOSE SDAP LOCAL CLUSTER ONLINE

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  GERR  The DIAGNOSE instruction could not be executed because
        of a global error.

HSV0059

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0059 ERROR DURING THE SVP FUNCTION DIAGNOSE SDAP VARY CLUSTER ONLINE

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  GERR  The DIAGNOSE instruction could not be executed because
        of a global error.

HSV0060

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0060 ERROR DURING THE SVP FUNCTION DIAGNOSE SDAP VARY CLUSTER OFFLINE

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  GERR  The DIAGNOSE instruction could not be executed because
        of a global error.

HSV0061

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0061 ERROR DURING THE SVP FUNCTION DIAGNOSE SDAP CREATE SCMP

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  BUSY  The DIAGNOSE instruction was completed with condition code 2
        or the SVP driver is busy.
  NSUP  The DIAGNOSE instruction was completed with condition code 3.
  GERR  The DIAGNOSE instruction could not be executed because
        of a global error.

HSV0062

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0062 ERROR DURING THE SVP FUNCTION DIAGNOSE RSC DR-CONTROL

Meaning

During the function an error was reported by the SVP.
The returncode has the following meaning:
  BUSY  The SVP driver is busy.
  NSUP  The function is not supported.
  CC=1  The DIAGNOSE instruction was completed with condition code 1.
  CC=2  The DIAGNOSE instruction was completed with condition code 2.
  CC=3  The DIAGNOSE instruction was completed with condition code 3.

HSV0063

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0063 ERROR DURING THE SVP FUNCTION DIAGNOSE RSC DR-RESPONSE

Meaning

HSV0064

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0064 ERROR DURING THE SVP FUNCTION DIAGNOSE READ FIRMWARE-INFO

Meaning

HSV0069

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0069 ERROR DURING THE SVP FUNCTION DIAGNOSE DEFINE MEMORY DOMAINS

Meaning

HSV0070

Destination: CONSOLE Routing code: * (main console) Weight: 99

Warranty : NO

HSV0070 ERROR DURING THE SVP FUNCTION DIAGNOSE WRITE VM DATA