Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA0A51 DCM DUMP INITIATED AT (&00)
Meaning
A DCM dump is initiated. (&00) indicates the location at which the error
was detected or from which the dump request was issued.
Response
Submit the dump.
BCA0A52
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA0A52 DCM-DUMP INITIATED AT (&00). DIAGNOSTIC INFORMATION: (&01) ((&02))
Meaning
A DCM-Dump is initiated.
(&00) indicates the location at which the error
was detected or from which the dump request was issued.
(&01) sedecimal information: internal code or return code of system call.
(&02) mnemotechnic abbreviation of a function. Qualifies sedecimal
information.
INTN internal code MEMG memory management retcode
BCAM BCAM return code SLOT slot pool management retcode
BOUR bourse-interface retcode NAMG name manager return code
P1EV P1-eventing return code TINF TCB-access return code
NEAB Station level protocol EXIT EXIT handler return code
CNTY P1-Contingency return code.
Response
Take dump (if the error cannot be found by means of the diagnostic
information).
BCA0B01
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0B01 MEM-RES: LIMIT=(MIN=(&00),ACT=(&01)), USED=(BCAM=(MIN=(I=(&02),O=(&03), R=(&07)),MAX=(I=(&04),O=(&05),R=(&08))), SYSTEM=(&06))
Meaning
Periodic message requested by /BCSET THRESHOLD-MSG=ON :
(&00) : minimal upper limit (in Kb)
(&01) : actual upper limit (in Kb)
(&02) : input data storage requested from BCAM buffer management;
minimum in the monitoring period just elapsed (in % of Threshold)
(&03) : output data storage requested from BCAM buffer management;
minimum in the monitoring period just elapsed (in % of Threshold)
(&04) : input data storage requested from BCAM buffer management;
maximum in the monitoring period just elapsed (in % of Threshold)
(&05) : output data storage requested from BCAM buffer management;
maximum in the monitoring period just elapsed (in % of Threshold)
(&06) : data storage requested from system buffer management (in Kb)
(&07) : data storage for routing requested from BCAM buffer management;
minimum in the monitoring period just elapsed (in % of Threshold)
(&08) : data storage for routing requested from BCAM buffer management;
maximum in the monitoring period just elapsed (in % of Threshold)
BCA0B07
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0B07 MEM-RES WARNING: LIMIT=(MIN=(&00),ACT=(&01)), USED=(BCAM=(I=(&02))), SYSTEM=(&03)
Meaning
Warning for use of resident input data storage :
(&00) : minimal upper limit (in Kb)
(&01) : actual upper limit (in Kb)
(&02) : input data storage requested from BCAM buffer management;
(in % of Threshold)
(&03) : data storage requested from system buffer management (in Kb)
BCA0B15
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0B15 LINE "(&00)": BYTES=(I=(&01)/O=(&02)); I/O'S=(I=(&03)/O=(&04)); PACKETING=(I=(&05)/O=(&06))
Meaning
Periodic message requested by /BCMON RECORD=L2:
(&00) : name of line
(&01) : number of input bytes
(&02) : number of output bytes
(&03) : number of correct reads
(&04) : number of correct writes
(&05) : number of data elements per read I/O
(&06) : number of data elements per write I/O
BCA0B16
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0B16 LINE "(&00)": UNICASTs=(I=(&01)/O=(&02)); MULTICASTs=(I=(&03)/O=(&04))
Meaning
Periodic message requested by /BCMON RECORD=L2:
(&00) : name of line
(&01) : number of unicasts received
(&02) : number of unicasts sent
(&03) : number of multicasts received
(&04) : number of multicasts sent
BCA0B18
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0B18 LINE "(&00)": I/O ERRORs=(I=(&01)/O=(&02)); WAIT+RETRIES=(&03); DISCARDS=(I=(&04)/O=(&05)); PROTOCOL ERRORs=(I=(&06)/O=(&07)); DATA CELL ERRORs=(&08)
Meaning
Periodic message requested by /BCMON RECORD=L2:
(&00) : name of line
(&01) : number of read errors
(&02) : number of write errors
(&03) : number of wait and retries for I/O's
(&04) : number of discarded input data elements
(&05) : number of discarded output data elements
(&06) : number of erroneous data elements received
(&07) : number of erroneous data elements sent
(&08) : number of discarded input data elements
caused by missing data cells
BCA0B19
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0B19 LINE "(&00)": IO-TIME SDV -> TI=(I=(&01)/O=(&03)); IO-TIME TI -> SDV=(I=(&02)/O=(&04))
Meaning
Periodic message requested by /BCMON RECORD=L2, ...
IO-time per IO.
(time difference format HH:MM:SS.TTTTTT
output of hour and minute may be suppressed)
(&00) : line name
(&01) : IO-TIME for input SDV -> TI
(&02) : IO-TIME for input TI -> SDV
(&03) : IO-TIME for output SDV -> TI
(&04) : IO-TIME for output TI -> SDV
BCA0B20
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0B20 LDU: (&00); RDU: (I=(&01), O=(&02)); BTU: (&03)
Meaning
Periodic message requested by /BCMON RECORD=TRANSFER or /BCMON RECORD=STD
:
(&00) : number of local transport service data units
(&01) : number of remote input transport service data units
(&02) : number of remote output transport service data units
(&03) : number of bad transport protocol data units
BCA0B21
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0B21 MEM-RES: LIMIT=(MIN=(&00),ACT=(&01)), USED=(BCAM=(MIN=(I=(&02),O=(&03), R=(&07)),MAX=(I=(&04),O=(&05),R=(&08))), SYSTEM=(&06))
Meaning
Periodic message requested by /BCMON RECORD=RES-MEMORY
or /BCMON RECORD=STD :
(&00) : minimal upper limit (in Kb)
(&01) : actual upper limit (in Kb)
(&02) : input data storage (in Kb) requested from BCAM buffer
management; minimum in the monitoring period just elapsed
(&03) : output data storage (in Kb) requested from BCAM buffer
management; minimum in the monitoring period just elapsed
(&04) : input data storage (in Kb) requested from BCAM buffer
management; maximum in the monitoring period just elapsed
(&05) : output data storage (in Kb) requested from BCAM buffer
management; maximum in the monitoring period just elapsed
(&06) : data storage (in Kb) requested from system buffer management
(&07) : data storage (in Kb) for routing requested from BCAM buffer
management; minimum in the monitoring period just elapsed
(&08) : data storage (in Kb) for routing requested from BCAM buffer
management; maximum in the monitoring period just elapsed
BCA0B22
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0B22 CON: (TOTAL=(&00),ACTIVE=(&03)); APP: (&01); APM: (&02)
Meaning
Periodic message requested by /BCMON RECORD=CONNECTIONS
or /BCMON RECORD=STD :
(&00) : number of existing connections
(&01) : number of opened applications
(&02) : number of openings of application
(&03) : number of active connections
BCA0B23
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0B23 MEM-PAG: LIMIT=(&00), USED=(BCAM=(&01),SYSTEM=(&02))
Meaning
Periodic message requested by /BCMON RECORD=PAG-MEMORY
or /BCMON RECORD=STD :
(&00) : upper limit for pageable data storage in Kb
(&01) : pageable data storage in Kb actually requested
from BCAM buffer management
(&02) : pageable data storage in Kb actually requested
from system memory management
BCA0B24
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0B24 ROUTING: (&00) IP / (&01) ISO / (&02) NEA PDU'S
Meaning
Periodic message requested by /BCMON RECORD=ROUTING
(&00) : number of IP datagrams routed in the monitoring period just
elapsed
(&01) : number of ISO8473 datagrams routed in the monitoring period just
elapsed
BCA0B30
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0B30 REMOTE:I=(&00)/O=(&01); LOCAL:I=(&02)/O=(&03)
Meaning
Periodic message requested by /BCMON RECORD=L4.
Following counters of the Layer 4 interface are given:
(&00) : number of received bytes on remote connections
(&01) : number of sent bytes on remote connections
(&02) : number of received bytes on local connections
(&03) : number of sent bytes on local connections
BCA0B31
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0B31 Connection Setups: Active=(OK=(&00),Failure=(&01)); Passive=(OK=(&02), Failure=(&03))
Meaning
Periodic message requested by /BCMON RECORD=MODIFY-CONNECTION :
(&00) : number of performed active setups of connections
(&01) : number of failed active setups of connections
(&02) : number of performed passive setups of connections
(&03) : number of failed passive setups of connections
BCA0B32
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0B32 LDU: (&00); RDU: (I=(&01), O=(&02)); BTU: (&03); LOOP-DU: (I=(&04), O=(&05))
Meaning
Periodic message requested by /BCMON RECORD=TR-DATA
:
(&00) : number of local transport service data units
(&01) : number of remote input transport service data units
(&02) : number of remote output transport service data units
(&03) : number of bad transport protocol data units
(&04) : number of loopback input transport service data units
(&05) : number of loopback output transport service data units
BCA0B40
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0B40 UDP: INPUT=(TOTAL: (&00), UNKNOWN PORT#: (&01), ERROR: (&02)); OUTPUT: (&03)
Meaning
Periodic message requested by /BCMON RECORD=DATAGRAM :
(&00) : total number of input UDP fragments
(&01) : number of input UDP fragments to unknown PORT#
(&02) : number of erroneous input UDP fragments
(&03) : total number of output UDP fragments
BCA0B41
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0B41 LOOPBACK:I=(&00)/O=(&01)
Meaning
Periodic message requested by /BCMON RECORD=LOOPBACK.
Following counters of the Layer 4 interface are given:
(&00) : number of received bytes on loopback connections
(&01) : number of sent bytes on loopback connections
BCA0B5C
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0B5C VLAN-DEVICE "(&00)": BYTES=(I=(&01)/O=(&02)); I/O'S=(I=(&03)/O=(&04)); PACKETING=(I=(&05)/O=(&06))
Meaning
Periodic message requested by /BCMON RECORD=VLAN-DEVICE:
(&00) : name of VLAN-device
(&01) : number of input bytes
(&02) : number of output bytes
(&03) : number of correct reads
(&04) : number of correct writes
(&05) : number of data elements per read I/O
(&06) : number of data elements per write I/O
BCA0B5D
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0B5D VLAN-DEVICE "(&00)": UNICASTs=(I=(&01)/O=(&02)); MULTICASTs=(I=(&03)/O=(&04))
Meaning
Periodic message requested by /BCMON RECORD=L2:
(&00) : name of device
(&01) : number of unicasts received
(&02) : number of unicasts sent
(&03) : number of multicasts received
(&04) : number of multicasts sent
BCA0B5E
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0B5E VLAN-DEVICE "(&00)": I/O ERRORs=(I=(&01)/O=(&02)); WAIT+RETRIES=(&03); DISCARDS=(I=(&04)/O=(&05)); PROTOCOL ERRORs=(O=(&06)); DATA CELL ERRORs=(&07)
Meaning
Periodic message requested by /BCMON RECORD=VLAN-DEVICE:
(&00) : name of VLAN-device
(&01) : number of read errors
(&02) : number of write errors
(&03) : number of wait and retries for I/O's
(&04) : number of discarded input data elements
(&05) : number of discarded output data elements
(&06) : number of erroneous data elements sent
(&07) : number of discarded input data elements
caused by missing data cells
BCA0B5F
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0B5F VLAN-DEVICE "(&00)": IO-TIME SDV -> TI=(I=(&01)/O=(&03)); IO-TIME TI -> SDV=(I=(&02)/O=(&04))
Meaning
Periodic message requested by /BCMON RECORD=VLAN-DEVICE, ...
IO-time per IO.
(time difference format HH:MM:SS.TTTTTT
output of hour and minute may be suppressed)
(&00) : device name
(&01) : IO-TIME for input SDV -> TI
(&02) : IO-TIME for input TI -> SDV
(&03) : IO-TIME for output SDV -> TI
(&04) : IO-TIME for output TI -> SDV
BCA0B50
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0B50 VLAN-LINE "(&00)": BYTES=(I=(&01)/O=(&02)); UNICASTs=(I=(&03)/O=(&04)); MULTICASTs=(I=(&05)/O=(&06))
Meaning
Periodic message requested by /BCMON RECORD=VLAN-LINE:
(&00) : name of VLAN-line
(&01) : number of input bytes
(&02) : number of output bytes
(&03) : number of unicasts received
(&04) : number of unicasts sent
(&05) : number of multicasts received
(&06) : number of multicasts sent
BCA0B51
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0B51 VLAN-LINE "(&00)": DISCARDS=(I=(&01)); PROTOCOL ERRORs=(I=(&02))
Meaning
Periodic message requested by /BCMON RECORD=VLAN-LINE:
(&00) : name of VLAN-line
(&01) : number of discarded input data elements
(&02) : number of erroneous data elements received
BCA0B60
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0B60 SIH-TIME total=(&00)/((&01)%); TI-OUT=(&02)/((&03)%); TI-IN=(&04)/((&05)%); KA-0=(&06)/((&07)%)
Meaning
Periodic message requested by /BCMON RECORD=SIH-TIME
(time difference format HH:MM:SS.TTTTTT
output of hour and minute may be suppressed)
(&00) : total SIH-TIME
(&01) : part of SIH-TIME for total SIH-TIME
(&02) : TI-OUT termination interrupt OUTPUT
(&03) : part of SIH-TIME for termination interrupt OUTPUT
(&04) : TI-IN termination interrupt for INPUT
(&05) : part of SIH-TIME for termination interrupt INPUT
(&06) : SIH-TIME for KA-process KA-0
(&07) : part of SIH-TIME for KA-process KA-0
BCA0B61
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0B61 SIH-TIME KA-1=(&00)/((&01)%); KA-2=(&02)/((&03)%); KA-3=(&04)/((&05)%); KA-4=(&06)/((&07)%)
Meaning
Periodic message requested by /BCMON RECORD=SIH-TIME
(time difference format HH:MM:SS.TTTTTT
output of hour and minute may be suppressed)
(&00) : SIH-TIME for KA-process KA-1
(&01) : part of SIH-TIME for KA-process KA-1
(&02) : SIH-TIME for KA-process KA-2
(&03) : part of SIH-TIME for KA-process KA-2
(&04) : SIH-TIME for KA-process KA-3
(&05) : part of SIH-TIME for KA-process KA-3
(&06) : SIH-TIME for KA-process KA-4
(&07) : part of SIH-TIME for KA-process KA-4
BCA0B62
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0B62 SIH-TIME KA-5=(&00)/((&01)%); KA-6=(&02)/((&03)%); KA-7=(&04)/((&05)%)
Meaning
Periodic message requested by /BCMON RECORD=SIH-TIME
(time difference format HH:MM:SS.TTTTTT
output of hour and minute may be suppressed)
(&00) : SIH-TIME for KA-process KA-5
(&01) : part of SIH-TIME for KA-process KA-5
(&02) : SIH-TIME for KA-process KA-6
(&03) : part of SIH-TIME for KA-process KA-6
(&04) : SIH-TIME for KA-process KA-7
(&05) : part of SIH-TIME for KA-process KA-7
BCA0B63
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0B63 SIH-TIME INPUT KA PROCESS L2=(&00)/((&01)%); L3=(&02)/((&03)%); L4=(&04)/((&05)%)
Meaning
Periodic message requested by /BCMON RECORD=SIH-TIME
(time difference format HH:MM:SS.TTTTTT
output of hour and minute may be suppressed)
(&00) : SIH-TIME for INPUT KA-process in L2
(&01) : part of SIH-TIME for INPUT KA-process in L2
(&02) : SIH-TIME for INPUT KA-process in L3
(&03) : part of SIH-TIME for INPUT KA-process in L3
(&04) : SIH-TIME for INPUT KA-process in L4
(&05) : part of SIH-TIME for INPUT KA-process in L4
BCA02A0
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA02A0 HOST entry not found
BCA02A1
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA02A1 NODE entry not found
BCA02A2
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA02A2 LINE entry not found
BCA02A3
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA02A3 LINK-AGGREGATION entry not found
BCA02A4
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA02A4 PROCESSOR entry not found
BCA02A5
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA02A5 ROUTE entry not found
BCA02A6
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA02A6 VLAN-DEVICE entry not found
BCA02A7
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA02A7 VLAN-LINE entry not found
BCA02A8
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA02A8 DNS name entry not found
BCA02A9
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA02A9 BCAM name entry not found
BCA02B0
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA02B0 no IP BCAM FIREWALL entry found
BCA02B1
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA02B1 no IPV6 BCAM FIREWALL entry found
BCA02B2
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA02B2 no IP ROUTER entry found
BCA02B3
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA02B3 no IPV6 ROUTER entry found
BCA0200
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA0200 system error occurred
BCA0201
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA0201 internal system error occurred
BCA0202
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA0202 user not privileged to execute the command
BCA0203
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA0203 error occurred at (&00) with RC (&01)
BCA0206
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA0206 BS2000 subsystem SATCP not available
Meaning
return code 'link error' at using macro $SATBCM.
Response
None. BCAM tries to continue SAT logging.
BCA0208
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA0208 BCAM Mapping not initialized
BCA0212
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA0212 operand error occurred
BCA0214
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA0214 combination of operand values not supported
BCA0215
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA0215 operand suppressed
BCA0216
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA0216 no fitting mapping entry found
BCA0222
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA0222 No host entry in BCAM Mapping found
BCA0232
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA0232 host entry not found
BCA0234
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA0234 modification not executed
BCA0235
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0235 JV (&00) could not be used. Reason: (&01)
Meaning
The JV with name (&00) could not be used because of
the following reason (&01) detected during the
/CREATE-VIRTUAL-HOST command:
ALREADY USED already used by BCAM
PROTECTED JV protected
MJV Monitoring JV
ERR JV NAME error in JV name
ERR USERID error in specified userid
BCA0236
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0236 JV (&00) could not be used. Reason: (&01)
Meaning
The JV with name (&00) could not be used because of
the following reason (&01) detected during the
/MODIFY-HOST-ATTRIBUTES command:
ALREADY USED already used by BCAM
PROTECTED JV protected
MJV Monitoring JV
ERR JV NAME error in JV name
ERR USERID error in specified userid
BCA0237
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0237 error occurred during update of JV
Meaning
The Update of JV could actually not be done. Detailed
information will be found in CONSLOG, especially in
message BCA0777.
BCA0242
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA0242 NO LINE TO NODE "(&00)" DEFINED
BCA0290
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA0290 (&00) entry not found
Meaning
The (&00) Entry was not found.
The insert may take the following values:
HOST host
NODE node
LINE line
LINK-AGGREGATION link-aggregation
PROCESSOR processor
ROUTE route
VLAN-DEVICE VLAN device
VLAN-LINE VLAN line
BCA0291
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA0291 (&00) table not found
Meaning
The (&00) table was not found.
The insert may take the following values:
IP-RANGE ip-range table
GATEWAY gateway table
BCA0292
Destination: USER-TASK Routing code: Weight:
Warranty : NO
BCA0292 no (&00) entry found satisfying the selection criteria
Meaning
No (&00) Entry was found satisfying the selection criteria.
The insert may take the following values:
HOST Host
NODE node
LINE line
PROCESSOR processor
ROUTE route
VLAN-DEVICE VLAN device
VLAN-LINE VLAN line
BCA0310
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0310 DCM TRACE SERVICES: TRACE TASK STARTED
Meaning
The central trace control and saving task has been successfully started.
BCA0311
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0311 DCM TRACE SERVICES: SAVING FILE (&00) OPENED
Meaning
The saving file has been successfully opened.
(&00)= Name of the saving file.
BCA0312
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0312 DCM TRACE SERVICES: (&00) PAM-PAGES SAVED
Meaning
The indicated number of PAM-pages have already been saved
in the saving file.
(&00)= Number of PAM-pages saved.
Response
Saving could be continued or terminated as you like.
The indicated number of PAM-pages already saved in the
saving file may be used as an aid for deciding.
BCA0317
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0317 DCM TRACE SERVICES: TRACE TASK TERMINATED
Meaning
The central trace control and saving task has been terminated.
Recording and saving of trace information have been stopped.
BCA0318
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0318 DCM TRACE SERVICES: SAVING FILE (&00) CLOSED
Meaning
The saving file has been closed.
(&00)= Name of the saving file.
BCA0319
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0319 DCM TRACE SERVICES: SAVING FILE (&00) ERASED
Meaning
The saving file has been erased.
(&00)= Name of the saving file.
BCA0330
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA0330 TRACE: (&00);STATE=(&01),BUFLEN=(&02),BUFNUM=(&03)
Meaning
(&00) = Name of the Trace
(&01) = State of the Trace: RUNNING or STOPPED
The state RUNNING has to be described more exactly.
RUNNING/INIT trace entries created only in buffer.
RUNNING/HOLD
RUNNING/SAVE trace entries will be created in output file.
RUNNING/SAVE-REQUESTED trace entries will not be created in
output file. The output file is not opened.
STOPPED No trace entries will be created.
(&02) = length of a TRACE Buffer.
(&03) = number of TRACE Buffers.
BCA05BA
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA05BA AGGREGATION "(&00)": No DEVICE active
BCA05BB
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA05BB AGGREGATION "(&00)" not active
BCA05BC
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA05BC AGGREGATION "(&00)" active
BCA05BD
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA05BD AGGREGATION "(&00)": Activation failed; reason: (&01)
Meaning
Activation of AGGREGATION (&00) failed
due to error '(&01)'.
(&01): sedecimal value identifying the error:
= 01 not enough system memory
= 04 system error
= FF invalid request at IPORT-ADM
Response
01 : Increase the memory limit by /BCMOD RESMEM= and
repeat the command.
BCA05BE
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA05BE AGGREGATION "(&00)" inactive reason: (&01)
Meaning
AGGREGATION (&00) was deactivated
reason:
(&01) = 01 normal deactivation
= 02 administrative deactivation
= 09 deactivated by VLAN-DEVICE handling
= 2B AGGREGATION-NAME exists in duplicate
Response
Corresponding to the reason:
(&01) = 01,02,09 none
= 2B The configuration is invalid.
AGGREGATION-NAME exists in duplicate. Use a different
name.
BCA05BF
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA05BF AGGREGATION "(&00)" already deactivated
BCA05B2
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA05B2 AGGREGATION "(&00)": "(&01)" is set to "(&02)"
BCA05B3
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA05B3 AGGREGATION "(&00)": STATE is set to (ADM="(&01)",TRANSFER="(&02)")
Meaning
the state of the LINK-AGGREGATION will be displayed
(&00) name of the LINK-AGGREGATION
(&01) administrative state
= ACTIVE administrative active
= INACTIVE administrative inactive
= EXCLUDED excluded
(&02) transfer state
= WAIT-FOR-ACTIVATION activation is in process
= WAIT-FOR-DEACTIVATION deactivation is in process
= NOT-READY-TO-OPERATE not yet ready to work
= WORKING active
= NONE not yet activated
BCA05B9
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA05B9 AGGREGATION "(&00)": No DEVICE existing
BCA05DB
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA05DB VLAN-DEVICE "(&00)" not active
BCA05DC
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA05DC VLAN-DEVICE "(&00)" active
BCA05DD
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA05DD VLAN-DEVICE "(&00)": Activation failed; reason: (&01)
Meaning
Activation of VLAN-DEVICE (&00) failed
due to error '(&01)'.
(&01): sedecimal value identifying the error:
= 01 not enough system memory
= 02 device already allocated or not available
= 04 system error
= 0E error allocating the device
= FF invalid request at IPORT-ADM / INET-ADM
Response
01 : Increase the memory limit by /BCMOD RESMEM= and
repeat the command.
02,0E : Attach device or check the configuration.
BCA05DE
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA05DE VLAN-DEVICE "(&00)" inactive reason: (&01)
Meaning
VLAN-Device (&00) was deactivated
reason:
(&01) = 01 normal deactivation
= 02 administrative deactivation
= 03 software error
= 04 hardware error
= 05 timeout
= 06 device not online
= 07 attention interrupt
= 08 device detached
= 0A deactivated by AGGREGATION handling
= 23 HNC version not supported
= 26 DEVICE-NAME exists in duplicate
= 27 CRYPTO device not supported
= 29 VLAN not supported by device
= 2A FRAME CHAINING not supported by device
= 2C Aggregation queue error
= 2D AGGREGATION not supported by device
Response
Corresponding to the reason:
(&01) = 01,02,0A none
= 03 get error information (via ASTRID);
reenter activation command
= 04,06,08 correct hardware error or attach device;
reenter activation command
= 05 take dump of partner processor if possible
= 23,27,29,2A,2D correct the configuration.
= 26 The configuration is invalid.
DEVICE-NAME exists in duplicate. Use a different
name.
BCA05DF
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA05DF VLAN-DEVICE "(&00)" already deactivated
BCA05D0
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA05D0 VLAN-DEVICE "(&00)": "(&01)" changed to "(&02)"
BCA05D1
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA05D1 VLAN-DEVICE "(&00)": "(&01)" is already "(&02)"
BCA05D2
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA05D2 VLAN-DEVICE "(&00)": "(&01)" is set to "(&02)"
BCA05D3
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA05D3 VLAN-DEVICE "(&00)": STATE is set to (ADM="(&01)",TRANSFER="(&02)")
Meaning
the state of the VLAN-device will be displayed
(&00) name of the device
(&01) administrative state
= ACTIVE device is administrative active
= INACTIVE device is administrative inactive
= EXCLUDED device is excluded
(&02) transfer state
= WAIT-FOR-ACTIVATION activation is in process
= WAIT-FOR-DEACTIVATION deactivation is in process
= NOT-READY-TO-OPERATE device is not yet ready to work
= WORKING device is active
= NONE device is not yet activated
BCA05D4
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA05D4 VLAN-DEVICE "(&00)": DEVICES = (WRITE="(&01)",READ="(&02)")
BCA05D5
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA05D5 VLAN-DEVICE "(&00)" NOT deactivated
Meaning
Before processing the requested command
the VLAN-device (&00) must be deactivated.
Response
Repeat command after:
/DEACTIVATE-VLAN-DEVICE DEVICE-NAME=(&00)
BCA05D6
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA05D6 VLAN-DEVICE "(&00)": DEVICES changed to (WRITE="(&01)",READ="(&02)")
BCA05D7
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA05D7 VLAN-DEVICE "(&00)": DEVICES are already (WRITE="(&01)",READ="(&02)")
BCA05D8
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA05D8 VLAN-DEVICE "(&00)": is attached to a LINK-AGGREGATION
BCA05D9
Destination: CONSOLE Routing code: C Weight: 70
Warranty : YES
BCA05D9 VLAN-DEVICE "(&00)": to LINK-AGGREGATION "(&01)"
BCA05EA
Destination: CONSOLE Routing code: C Weight: 70
Warranty : YES
BCA05EA VLAN-LINE "(&00)": to NODE "(&01)"
BCA05EB
Destination: CONSOLE Routing code: C Weight: 70
Warranty : YES
BCA05EB VLAN-LINE "(&00)": to VLAN-DEVICE "(&01)"
BCA05EC
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA05EC VLAN-LINE "(&00)" active
BCA05ED
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA05ED VLAN-LINE "(&00)": Activation failed; reason: (&01)
Meaning
Activation of VLAN-LINE (&00) failed
due to error '(&01)'.
(&01): sedecimal value identifying the error:
= 01 not enough system memory
= 02 device not available
= 04 system error
= FF invalid request at IPORT-ADM / INET-ADM
Response
01 : Increase the memory limit by /BCMOD RESMEM= and
repeat the command.
BCA05EE
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA05EE VLAN-LINE "(&00)" inactive reason: (&01)
Meaning
VLAN-line (&00) was deactivated
reason:
(&01) = 00 software error in the net layer
= 01 normal deactivation
= 02 administrative deactivation
= 03 software error
= 05 timeout
= 09 deactivated by VLAN-DEVICE handling
= 0A deactivated by AGGREGATION handling
= 24 VLAN-LINE-NAME exists in duplicate
= 25 VLAN-DEVICE-NAME not found
Response
Corresponding to the reason:
(&01) = 01,02,09,0A none
= 00,03 get error information (via ASTRID);
reenter activation command
= 25 Correct the configuration.
= 24 The configuration is invalid.
VLAN-LINE-NAME exists in duplicate. Use a different
name.
BCA05EF
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA05EF VLAN-LINE "(&00)" already deactivated
BCA05E0
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA05E0 VLAN-LINE "(&00)": "(&01)" changed to "(&02)"
BCA05E1
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA05E1 VLAN-LINE "(&00)": "(&01)" is already "(&02)"
BCA05E2
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA05E2 VLAN-LINE "(&00)": "(&01)" is set to "(&02)"
BCA05E3
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA05E3 VLAN-LINE "(&00)": STATE is set to (ADM="(&01)",TRANSFER="(&02)")
Meaning
the state of the VLAN-line will be displayed
(&00) name of the VLAN-line
(&01) administrative state
= ACTIVE VLAN-line is administrative active
= INACTIVE VLAN-line is administrative inactive
= EXCLUDED VLAN-line is excluded
(&02) transfer state
= WAIT-FOR-ACTIVATION activation is in process
= WAIT-FOR-DEACTIVATION deactivation is in process
= NOT-READY-TO-OPERATE VLAN-line is not yet ready to work
= WORKING VLAN-line is active
= NONE VLAN-line is not yet activated
BCA05E4
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA05E4 VLAN-LINE for VLAN-DEVICE "(&00)" and VLAN-ID "(&01)" already exists
BCA05E5
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA05E5 VLAN-LINE "(&00)" NOT deactivated
Meaning
Before processing the requested command
the VLAN-line (&00) must be deactivated.
Response
Repeat command after: '/DEACTIVATE-VLAN-LINE LINE-NAME=(&00)'
BCA05E6
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA05E6 VLAN-LINE for LINK-AGGREGATION "(&00)" and VLAN-ID "(&01)" already exists
BCA05E8
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA05E8 VLAN-LINE "(&00)": redundant to LINE "(&01)"
BCA05E9
Destination: CONSOLE Routing code: C Weight: 70
Warranty : YES
BCA05E9 VLAN-LINE "(&00)": to LINK-AGGREGATION "(&01)"
BCA0545
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0545 SLOW-POLL running on VLAN-DEVICE "(&00)"
Meaning
Slow-Poll running on VLAN-device (&00)
due to a former /MODIFY-VLAN-DEVICE command.
BCA0546
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0546 SLOW-POLL stopped for VLAN-DEVICE "(&00)"
Meaning
Slow-Poll stopped for VLAN-device (&00)
due to a former /MODIFY-VLAN-DEVICE command.
BCA0547
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0547 CHECKSUM done by DEVICE for VLAN-DEVICE "(&00)"
Meaning
CHECKSUM done by DEVICE for VLAN-device (&00)
due to a former /MODIFY-VLAN-DEVICE command.
BCA0548
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0548 CHECKSUM done by BCAM for VLAN-DEVICE "(&00)"
Meaning
CHECKSUM done by BCAM for VLAN-device (&00)
due to a former /MODIFY-VLAN-DEVICE command.
BCA0551
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0551 BROADCAST MODE SWITCHED ON for VLAN-LINE "(&00)"
Meaning
Broadcast mode was switched on for VLAN-line (&00)
due to a former /BCOPTION or /MODIFY-VLAN-LINE command.
BCA0552
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0552 BROADCAST MODE SWITCHED OFF for VLAN-LINE "(&00)"
Meaning
Broadcast mode was switched off for VLAN-line (&00)
due to a former /BCOPTION or /MODIFY-VLAN-LINE command.
BCA0553
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0553 MULTICAST MODE SWITCHED ON for VLAN-LINE "(&00)"
Meaning
Multicast mode was switched on for VLAN-line (&00)
due to a former /BCOPTION or /MODIFY-VLAN-LINE command.
BCA0554
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0554 MULTICAST MODE SWITCHED OFF for VLAN-LINE "(&00)"
Meaning
Multicast mode was switched off for VLAN-line (&00)
due to a former /BCOPTION or /MODIFY-VLAN-LINE command.
BCA0555
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0555 SLOW-POLL running on VLAN-LINE "(&00)"
Meaning
Slow-Poll running on for VLAN-line (&00)
due to a former /BCOPTION or /MODIFY-VLAN-LINE command.
BCA0556
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0556 SLOW-POLL stopped on VLAN-LINE "(&00)"
Meaning
Slow-Poll stopped on VLAN-line (&00)
due to a former /BCOPTION or /MODIFY-VLAN-LINE command.
BCA0557
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0557 CHECKSUM done implicitly by DEVICE for VLAN-LINE "(&00)"
Meaning
Checksum done implicitly by DEVICE for VLAN-line (&00)
due to a former /MODIFY-VLAN-DEVICE command.
BCA0558
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0558 CHECKSUM done implicitly by BCAM for VLAN-LINE "(&00)"
Meaning
Checksum done implicitly by BCAM for VLAN-line (&00)
due to a former /MODIFY-VLAN-DEVICE command.
BCA0560
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA0560 Actual MAX-LPDU value is "(&01)" for LINE "(&00)"
BCA0561
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA0561 Actual MAX-LPDU value is "(&01)" for VLAN-LINE "(&00)"
BCA0562
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0562 Actual MAX-LPDU value is "(&01)" for VLAN-DEVICE "(&00)"
BCA0564
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA0564 Actual "(&02)" value is "(&01)" for LINE "(&00)"
BCA0565
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA0565 Actual "(&02)" value is "(&01)" for VLAN-LINE "(&00)"
BCA0566
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA0566 Actual "(&02)" value is "(&01)" for VLAN-DEVICE "(&00)"
BCA057A
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA057A (&00)-ADDRESS (&01) of HOST "(&02)" is added to LINE "(&03)"
BCA057B
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA057B (&00)-ADDRESS (&01) of HOST "(&02)" is add to VLAN-LINE "(&03)"
BCA057C
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA057C (&00)-ADDRESS (&01) already deactivated on LINE "(&02)"
BCA057D
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA057D (&00)-ADDRESS (&01) already deactivated on VLAN-LINE "(&02)"
BCA057E
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA057E (&00)-ADDRESS (&01) of HOST "(&02)" is attached to LINE "(&03)"; address state: "(&04)"
Meaning
address information of a line
(&00) address type
= IP
= IPV6
= ISO
= LAN
(&01) address
(&02) host-name
(&03) name of line
(&04) address state
= TENTATIVE address in state testing
= VALID address may be used
= INVALID address already used in net
= DEACTIVATED address deactivated via command
= DUPLICATE address is duplicate
BCA057F
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA057F (&00)-ADDRESS (&01) of HOST "(&02)" is attached to VLAN-LINE "(&03)"; address state: "(&04)"
Meaning
address information of a VLAN line
(&00) address type
= IP
= IPV6
= ISO
= LAN
(&01) address
(&02) host-name
(&03) name of VLAN line
(&04) address state
= TENTATIVE address in state testing
= VALID address may be used
= INVALID address already used in net
= DEACTIVATED address deactivated via command
= DUPLICATE address is duplicate
BCA0570
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0570 (&00)-ADDRESS (&01) switched to LINE "(&02)"
BCA0571
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0571 (&00)-ADDRESS (&01) switched to VLAN-LINE "(&02)"
BCA0572
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0572 (&00)-ADDRESS (&01) activated on LINE "(&02)"
BCA0573
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0573 (&00)-ADDRESS (&01) activated on VLAN-LINE "(&02)"
BCA0574
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0574 (&00)-ADDRESS (&01) deactivated on LINE "(&02)"
BCA0575
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0575 (&00)-ADDRESS (&01) deactivated on VLAN-LINE "(&02)"
BCA0576
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0576 (&00)-ADDRESS (&01) not switched to LINE "(&02)"
Meaning
The address is not switched to line (&02), because the
reducing the size of LPDU SIZE is not possible.
(&00) address type IP or IPv6 or INTF
(&01) address
(&02) line name
BCA0577
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0577 (&00)-ADDRESS (&01) not switched to VLAN-LINE "(&02)"
Meaning
The address is not switched to line (&02), because the
reducing the size of LPDU SIZE is not possible.
(&00) address type IP or IPv6 or INTF
(&01) address
(&02) line name
BCA06AA
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA06AA SHOW-OWN-ADDRESS command aborted
BCA06A4
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA06A4 SHOW-LINE command aborted
BCA06A7
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA06A7 SHOW-LINK-AGGREGATION command aborted
BCA06A8
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA06A8 SHOW-VLAN-DEVICE command aborted
BCA06A9
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA06A9 SHOW-VLAN-LINE command aborted
BCA06BA
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA06BA MODIFY-OWN-ADDRESS aborted
BCA06B3
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA06B3 MODIFY-ROUTE-ATTRIBUTES command aborted
BCA06B4
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA06B4 MODIFY-LINE command aborted
BCA06B5
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA06B5 MODIFY-ROUTE-PATH command aborted
BCA06B6
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA06B6 MODIFY-ROUTE command aborted
BCA06B7
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA06B7 MODIFY-ADDRESS-ASSIGNMENT command aborted
BCA06B8
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA06B8 MODIFY-VLAN-DEVICE command aborted
BCA06B9
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA06B9 MODIFY-VLAN-LINE command aborted
BCA06CB
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA06CB VLAN-LINE "(&00)": ACTIVATE-VLAN-LINE aborted
BCA06CC
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA06CC LINE "(&00)": ACTIVATE-LINE aborted
BCA06CD
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA06CD VLAN-DEVICE "(&00)": ACTIVATE-VLAN-DEVICE aborted
BCA06CF
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA06CF AGGREGATION "(&00)": ACTIVATE-LINK-AGGREGATION aborted
BCA06C0
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA06C0 (&00)-ADDRESS "(&01)": ACTIVATE-OWN-ADDRESS aborted
BCA06C1
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA06C1 NODE "(&00)": CREATE-NODE aborted
BCA06C2
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA06C2 PROCESSOR "(&00)": CREATE-PROCESSOR aborted
BCA06C3
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA06C3 VLAN-LINE "(&00)": CREATE-VLAN-LINE aborted
BCA06C4
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA06C4 LINE "(&00)": CREATE-LINE aborted
BCA06C5
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA06C5 VLAN-DEVICE "(&00)": CREATE-VLAN-DEVICE aborted
BCA06C6
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA06C6 ROUTE "(&00)": CREATE-ROUTE aborted
BCA06C7
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA06C7 AGGREGATION "(&00)": CREATE-LINK-AGGREGATION aborted
BCA06C8
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA06C8 ADD-OWN-ADDRESS aborted
BCA06DA
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA06DA VLAN-LINE "(&00)": DEACTIVATE-VLAN-LINE aborted
BCA06DF
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA06DF AGGREGATION "(&00)": DEACTIVATE-LINK-AGGREGATION aborted
BCA06D0
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA06D0 (&00)-ADDRESS "(&01)": DEACTIVATE-OWN-ADDRESS aborted
BCA06D2
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA06D2 PROCESSOR "(&00)": DELETE-PROCESSOR aborted
BCA06D7
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA06D7 DELETE-ROUTE command aborted
BCA06D8
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA06D8 LINE "(&00)": DEACTIVATE-LINE aborted
BCA06D9
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA06D9 VLAN-DEVICE "(&00)": DEACTIVATE-VLAN-DEVICE aborted
BCA06EA
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA06EA PROCESSOR "(&00)" deleted
BCA06EE
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA06EE ROUTE "(&00)" deleted
BCA06E2
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA06E2 PROCESSOR "(&00)" created
BCA06E6
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA06E6 ROUTE "(&00)" created
BCA06FD
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA06FD No OWN-ADDRESS to be shown found
BCA06F4
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA06F4 No LINE to be shown found
BCA06F5
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA06F5 No VLAN-DEVICE to be shown found
BCA06F6
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA06F6 No VLAN-LINE to be shown found
BCA06F7
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA06F7 No LINK-AGGREGATION to be shown found
BCA060A
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA060A LINE "(&00)" has not same REDUNDANCY as VLAN-LINE "(&01)"
BCA060C
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA060C OWN-ADDRESS has not same NODE as VLAN-LINE "(&00)"
BCA060D
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA060D OWN-ADDRESS has not same REDUNDANCY as VLAN-LINE "(&00)"
BCA060E
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA060E OWN-ADDRESS has bigger LPDU SIZE as VLAN-LINE "(&00)"
BCA0601
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0601 LINE "(&00)" has not same NODE as LINE "(&01)"
BCA0602
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0602 LINE "(&00)" has not same REDUNDANCY as LINE "(&01)"
BCA0604
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0604 OWN-ADDRESS has not same NODE as LINE "(&00)"
BCA0605
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0605 OWN-ADDRESS has not same REDUNDANCY as LINE "(&00)"
BCA0606
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0606 OWN-ADDRESS has bigger LPDU SIZE as LINE "(&00)"
BCA0609
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0609 LINE "(&00)" has not same NODE as VLAN-LINE "(&01)"
BCA0610
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0610 SOME BCAM OPTIONS CHANGED
Meaning
One or several BCAM options are successfully changed by
/BCOPTION or /MODIFY-BCAM-OPTIONS.
BCA0611
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0611 NO BCAM OPTIONS CHANGED
Meaning
No BCAM options are changed by /BCOPTION
or /MODIFY-BCAM-OPTIONS.
BCA0612
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0612 SOME BCAM START VALUES CHANGED
Meaning
One or several BCAM start values are successfully changed by /BCMOD.
BCAM start values are values set by /DCSTART or /DCOPT.
BCA0613
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0613 NO BCAM START VALUES CHANGED
Meaning
No BCAM start values are changed by /BCMOD.
BCAM start values are values set by /DCSTART or /DCOPT.
BCA0614
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0614 DNS-ACCESS parameters changed
Meaning
One or several parameters are successfully changed
by /MODIFY-DNS-ACCESS.
BCA0615
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0615 No DNS-ACCESS parameter changed
Meaning
No parameter is changed by /MODIFY-DNS-ACCESS.
BCA0616
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0616 VLAN-ASSIGNMENT parameters changed
Meaning
One or several parameters are successfully changed
by /MODIFY-VLAN-ASSIGNMENT.
BCA0617
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0617 No VLAN-ASSIGNMENT parameter changed
Meaning
No parameter is changed by /MODIFY-VLAN-ASSIGNMENT.
BCA062A
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA062A SOME MONITORING STARTED
Meaning
Function "Start BCAM monitoring" was successfully processed
by BCAM command /BCMON.
BCA062B
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA062B NO MONITORING STARTED
Meaning
Function "Start BCAM monitoring" was not processed,
( BCAM command /BCMON ).
BCA062C
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA062C /BCSET COMMAND PROCESSED
Meaning
Function "Set diagnostic and maintenance operands" was successfully
processed by BCAM command /BCSET.
BCA062D
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA062D /BCSET COMMAND ABORTED
Meaning
Function "Set diagnostic and maintenance operands" was aborted,
( BCAM command /BCSET ).
BCA062E
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA062E MAPPING COMMAND PROCESSED
Meaning
Function "Control BCAM mapping function" was successfully
processed by BCAM command /BCMAP.
BCA062F
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA062F MAPPING COMMAND ABORTED
Meaning
Function "Control BCAM mapping function" was aborted,
( BCAM command /BCMAP ).
BCA0620
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0620 INCLUDING PROCESSED
Meaning
Function "Initialize/generate communication components" was
successfully processed by BCAM command /BCIN.
BCA0621
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0621 INCLUDING ABORTED
Meaning
Function "Initialize/generate communication components" was aborted,
( BCAM command /BCIN ).
BCA0622
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0622 ACTIVATION PROCESSED
Meaning
Function "Activate communication components" was
successfully processed by BCAM command /BCACT.
BCA0623
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0623 ACTIVATION ABORTED
Meaning
Function "Activate communication components" was aborted,
( BCAM command /BCACT ).
BCA0624
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0624 DEACTIVATION PROCESSED
Meaning
Function "Deactivate communication components" was
successfully processed by BCAM command /BCDAC.
BCA0625
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0625 DEACTIVATION ABORTED
Meaning
Function "Deactivate communication components" was aborted,
( BCAM command /BCDAC ).
BCA0626
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0626 CLOSE DOWN PROCESSED
Meaning
Function "Close down communication components" was
successfully processed by BCAM command /BCOUT.
BCA0627
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0627 CLOSE DOWN ABORTED
Meaning
Function "Close down communication components" was aborted,
( BCAM command /BCOUT ).
BCA0628
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0628 DEFINING TIMER PROCESSED
Meaning
Function "Define BCAM time intervals" was successfully processed
by BCAM command /BCTIMES.
BCA0629
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0629 DEFINING TIMER ABORTED
Meaning
Function "Define BCAM time intervals" was aborted,
( BCAM command /BCTIMES ).
BCA063A
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA063A SHUT DOWN OF CONNECTION PROCESSED
Meaning
The shut down of connection was processed,
( BCAM command /BCCONN ).
BCA063B
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA063B SHUT DOWN OF CONNECTION NOT PROCESSED
Meaning
The shut down of connection was not processed,
( BCAM command /BCCONN ).
BCA063C
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA063C SHUT DOWN OF CONNECTION PROCESSED
Meaning
The shut down of connection was processed,
( BCAM command /BCDISCON ).
BCA063D
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA063D SHUT DOWN OF CONNECTION NOT PROCESSED
Meaning
The shut down of connection was not processed,
( BCAM command /BCDISCON ).
BCA063E
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA063E CONNECTION PROPOSAL FOR APPLICATION PROCESSED
Meaning
The Connection proposal for an application was processed,
( BCAM command /BCCONP ).
BCA063F
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA063F CONNECTION PROPOSAL FOR APPLICATION NOT PROCESSED
Meaning
The Connection proposal for an application was not processed,
( BCAM command /BCCONP ).
BCA0630
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0630 SWITCH PORT COMMAND PROCESSED
Meaning
Function "Switch PORT" was successfully processed
by BCAM command /BCSWP.
BCA0631
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0631 SWITCH PORT COMMAND ABORTED
Meaning
Function "Switch PORT" was aborted,
( BCAM command /BCSWP ).
BCA0632
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA0632 /DCDIAG COMMAND PROCESSED
Meaning
Function "Control DCAM traces" was successfully processed
by BCAM command /DCDIAG.
BCA0634
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0634 SOME MONITORING STOPPED
Meaning
BCAM monitoring was stopped,
( BCAM command /BCMON ).
BCA0635
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0635 NO MONITORING STOPPED
Meaning
Stopping of BCAM monitoring was not processed,
( BCAM command /BCMOFF ).
BCA0636
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0636 ACTIVATION/DEACTIVATION OF APPLICATION PROCESSED
Meaning
The activation/deactivation of the application was processed,
( BCAM command /BCAPPL ).
BCA0637
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0637 ACTIVATION/DEACTIVATION OF APPLICATION NOT PROCESSED
Meaning
The activation/deactivation of the application was not processed,
( BCAM command /BCAPPL ).
BCA0638
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0638 DEACTIVATION OF APPLICATION PROCESSED
Meaning
The deactivation of the application was processed,
( BCAM command /BCLOSE ).
BCA0639
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0639 DEACTIVATION OF APPLICATION NOT PROCESSED
Meaning
The deactivation of the application was not processed,
( BCAM command /BCLOSE ).
BCA0642
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0642 CHANGE OF NAME AND/OR ADDRESS PROCESSED
Meaning
The change of name and/or address was processed,
( BCAM command /BCGEN ).
BCA0643
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0643 CHANGE OF NAME AND/OR ADDRESS NOT PROCESSED
Meaning
The change of name and/or address was not processed,
( BCAM command /BCGEN ).
BCA065A
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA065A SHOW-OWN-ADDRESS command processed
BCA0654
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0654 SHOW-LINE command processed
BCA0657
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0657 SHOW-LINK-AGGREGATION command processed
BCA0658
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0658 SHOW-VLAN-DEVICE command processed
BCA0659
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0659 SHOW-VLAN-LINE command processed
BCA066A
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA066A MODIFY-OWN-ADDRESS processed
BCA0663
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0663 MODIFY-ROUTE-ATTRIBUTES command processed
BCA0664
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0664 MODIFY-LINE command processed
BCA0665
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0665 MODIFY-ROUTE-PATH command processed
BCA0666
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0666 MODIFY-ROUTE command processed
BCA0667
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0667 MODIFY-ADDRESS-ASSIGNMENT command processed
BCA0668
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0668 MODIFY-VLAN-DEVICE command processed
BCA0669
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0669 MODIFY-VLAN-LINE command processed
BCA067B
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA067B VLAN-LINE "(&00)": ACTIVATE-VLAN-LINE processed
BCA067C
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA067C LINE "(&00)": ACTIVATE-LINE processed
BCA067D
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA067D VLAN-DEVICE "(&00)": ACTIVATE-VLAN-DEVICE processed
BCA067F
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA067F AGGREGATION "(&00)": ACTIVATE-LINK-AGGREGATION processed
BCA0670
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0670 (&00)-ADDRESS "(&01)": ACTIVATE-OWN-ADDRESS processed
BCA0671
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0671 NODE "(&00)": CREATE-NODE processed
BCA0672
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0672 PROCESSOR "(&00)": CREATE-PROCESSOR processed
BCA0673
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0673 VLAN-LINE "(&00)": CREATE-VLAN-LINE processed
BCA0674
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0674 LINE "(&00)": CREATE-LINE processed
BCA0675
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0675 VLAN-DEVICE "(&00)": CREATE-VLAN-DEVICE processed
BCA0676
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0676 ROUTE "(&00)": CREATE-ROUTE processed
BCA0677
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0677 AGGREGATION "(&00)": CREATE-LINK-AGGREGATION processed
BCA0678
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0678 ADD-OWN-ADDRESS processed
BCA068A
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA068A VLAN-LINE "(&00)": DEACTIVATE-VLAN-LINE processed
BCA068F
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA068F AGGREGATION "(&00)": DEACTIVATE-LINK-AGGREGATION processed
BCA0680
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0680 (&00)-ADDRESS "(&01)": DEACTIVATE-OWN-ADDRESS processed
BCA0682
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0682 PROCESSOR "(&00)": DELETE-PROCESSOR processed
BCA0687
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0687 DELETE-ROUTE command processed
BCA0688
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0688 LINE "(&00)": DEACTIVATE-LINE processed
BCA0689
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0689 VLAN-DEVICE "(&00)": DEACTIVATE-VLAN-DEVICE processed
BCA0690
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA0690 NEA ADDRESSES no longer supported !!!!
Meaning
NEA addresses are no longer supported.
The definitions of NEA addresses are ignored.
Response
The definitions of NEA addresses should be eliminated.
BCA0691
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA0691 WAN NET and NEA ADDRESSES no longer supported !!!!
Meaning
WAN Net and NEA addresses are no longer supported.
The definitions of WAN net and NEA addresses are ignored.
Response
The definitions of WAN net and NEA addresses should be eliminated.
BCA07AA
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07AA VLAN-LINE "(&00)" UNKNOWN
BCA07AB
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07AB No VLAN-LINE found for LINK-AGGREGATION "(&00)"
BCA07AC
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07AC No VLAN-LINE found for VLAN-DEVICE "(&00)"
BCA07AD
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07AD LINE "(&00)" is no NODE line
BCA07AE
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07AE NODE "(&00)" is a VLAN NODE
BCA07AF
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07AF NODE "(&00)" is not a VLAN NODE
BCA07A0
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07A0 PROCESSOR "(&00)" UNKNOWN
BCA07A1
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07A1 ROUTE "(&00)" UNKNOWN
BCA07A2
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07A2 LINE "(&00)" UNKNOWN
BCA07A3
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07A3 NODE "(&00)" UNKNOWN
BCA07A4
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07A4 HOST "(&00)" UNKNOWN
BCA07A5
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07A5 VLAN-DEVICE "(&00)" UNKNOWN
BCA07A6
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07A6 No VLAN-DEVICE found for LINK-AGGREGATION "(&00)"
BCA07A7
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07A7 LINK-AGGREGATION "(&00)" UNKNOWN
BCA07A8
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07A8 PROCESSOR "(&00)" NOT EXCLUDED
Meaning
Before processing the requested command
the processor (&00) must be excluded.
Response
Repeat command after: /BCOUT PROCESSOR=(&00)
BCA07A9
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07A9 ROUTE "(&00)" NOT EXCLUDED
Meaning
Before processing the requested command
the route (&00) must be excluded.
Response
Repeat command after: /BCOUT ROUTE=(&00)
BCA07B0
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA07B0 ROUTE "(&00)" USED AS (&01)-ROUTER FOR ADDRESS "(&02)"
Meaning
Routing functions are performed via route (&00) now.
(&01) : IP - routing for IP address (&02)
ISO8473 - routing due to ISO8473 protocol for INTF address (&02)
IPV6 - routing for IPV6 address (&02)
(&02) : *UNKNOWN - routing for all addresses not defined elsewhere
BCA07B1
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA07B1 ROUTE "(&00)" NO MORE USED AS (&01)-ROUTER FOR ADDRESS "(&02)"
Meaning
Routing functions are no more performed via route (&00).
(&01) : IP - routing for IP address (&02)
ISO8473 - routing due to ISO8473 protocol for INTF address (&02)
IPV6 - routing for IPV6 address (&02)
(&02) : *UNKNOWN - definition of default router is withdrawn
BCA07B2
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA07B2 ROUTE(S) SWITCHED FROM LINE "(&00)" TO LINE "(&01)"; REASON: "(&02)"
Meaning
Routes are switched from line (&00) to line (&01).
Reason: (&02) = 01 error from line (&00)
= 02 switching caused by line activation
= 03 error from line supervision
Response
Check line "(&00)"
BCA07B3
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA07B3 ROUTE "(&00)" (own address (&01)) used as IP-ROUTER for (&02)
Meaning
IP routing functions are performed via route (&00) now.
(&01) : own address of route
(&02) : *UNKNOWN - routing for all addresses not defined elsewhere
BCA07B4
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA07B4 ROUTE "(&00)" (own address (&01)) no more used as IP-ROUTER for (&02)
Meaning
IP routing functions are no more performed via route (&00).
(&01) : own address of route
(&02) : *UNKNOWN - definition of default router is withdrawn
BCA07B5
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA07B5 ROUTE "(&00)" (own address (&01)) used as IPV6-ROUTER for (&02)
Meaning
IPV6 routing functions are performed via route (&00) now.
(&01) : own address of route
(&02) : *UNKNOWN - routing for all addresses not defined elsewhere
BCA07B6
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA07B6 ROUTE "(&00)" (own address (&01)) no more used as IPV6-ROUTER for (&02)
Meaning
IPV6 routing functions are no more performed via route (&00).
(&01) : own address of route
(&02) : *UNKNOWN - definition of default router is withdrawn
BCA07CA
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA07CA No ROUTE to be deleted found
BCA07CE
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA07CE FIREWALL ROUTE: modification not allowed
BCA07C0
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07C0 NO ROUTE MODIFIED
Meaning
No route modification was performed due to the last command.
The reason was announced in an own message.
BCA07C1
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA07C1 (&00) ROUTES TO PROCESSOR "(&01)" MODIFIED
Meaning
This message is displayed after a /MODIFY-ROUTE or
/MODIFY-ROUTE-ATTRIBUTES command, if more than
one route was referenced with this command.
Each change was announced with an own message (BCA07C2).
BCA07C2
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA07C2 ROUTE "(&00)" TO PROCESSOR "(&01)" MODIFIED
Meaning
This message is always displayed when route attributes were modified
due to a /MODIFY-ROUTE, /MODIFY-ROUTE-ATTRIBUTES or
/BCOPTION command with ARP/TIMER=. If only one
route was selected, positive command end is signaled with this message.
BCA07C3
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA07C3 ROUTE "(&00)": "(&01)" is set to "(&02)"
Meaning
The NSDU value ist set due to L2/L3 restrictions.
BCA07C4
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA07C4 operand "(&00)" will not be set due to not matching "(&01)"
Meaning
The operand value will not be set due to restrictions.
BCA07DA
Destination: CONSOLE Routing code: C Weight: 70
Warranty : YES
BCA07DA LINE "(&00)": to NODE "(&01)"
BCA07DC
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA07DC LINE "(&00)" active
BCA07DD
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA07DD LINE "(&00)": Activation failed; reason: (&01)
Meaning
Activation of LINE (&00) failed
due to error '(&01)'.
(&01): sedecimal value identifying the error:
= 01 not enough system memory
= 02 device already allocated or not available
= 04 system error
= 06 invalid device type
= 07 attention interrupt
= 0E error allocating the device
= FF invalid request at IPORT-ADM / INET-ADM
Response
01 : Increase the memory limit by /BCMOD RESMEM= and
repeat the command.
06 : Correct device error and repeat command
02,0E : Attach device or check the configuration.
BCA07DE
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA07DE LINE "(&00)" inactive reason: (&01)
Meaning
Line (&00) was deactivated
reason:
(&01) = 00 software error in the net layer
= 01 normal deactivation
= 02 administrative deactivation
= 03 software error
= 04 hardware error
= 05 timeout
= 06 device not online
= 07 attention interrupt
= 08 device detached
= 23 HNC version not supported
= 24 LINE-NAME exists in duplicate
= 27 CRYPTO device not supported
= 2A FRAME CHAINING not supported
Response
Corresponding to the reason:
(&01) = 01,02 none
= 00,03 get error information (via ASTRID);
reenter activation command
= 04,06,08 correct hardware error or attach device;
reenter activation command
= 05 take dump of partner processor if possible
= 23,27,2A Correct the configuration.
= 24 The configuration is invalid.
LINE-NAME exists in duplicate. Use a different
name.
BCA07DF
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA07DF LINE "(&00)": redundant to LINE "(&01)"
BCA07D0
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA07D0 LINE "(&00)": "(&01)" changed to "(&02)"
BCA07D1
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA07D1 LINE "(&00)": "(&01)" is already "(&02)"
BCA07D2
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA07D2 LINE "(&00)": "(&01)" is set to "(&02)"
BCA07D3
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA07D3 LINE "(&00)": STATE is set to (ADM="(&01)",TRANSFER="(&02)")
Meaning
the state of the line will be displayed
(&00) name of the line
(&01) administrative state
= ACTIVE line is administrative active
= INACTIVE line is administrative inactive
= EXCLUDED line is excluded
(&02) transfer state
= WAIT-FOR-ACTIVATION activation is in process
= WAIT-FOR-DEACTIVATION deactivation is in process
= NOT-READY-TO-OPERATE line is not yet ready to work
= WORKING line is active
= NONE line is not yet activated
BCA07D4
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA07D4 LINE "(&00)": DEVICES = (WRITE="(&01)",READ="(&02)")
BCA07D5
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07D5 LINE "(&00)" NOT deactivated
Meaning
Before processing the requested command
the line (&00) must be deactivated.
Response
Repeat command after: deactivation command
BCA07D6
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA07D6 LINE "(&00)": DEVICES changed to (WRITE="(&01)",READ="(&02)")
BCA07D7
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA07D7 LINE "(&00)": DEVICES are already (WRITE="(&01)",READ="(&02)")
BCA07EA
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07EA PROCESSOR "(&00)": (&01) command running
BCA07EB
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07EB ROUTE "(&00)": Route is in use
BCA07EC
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07EC ROUTE "(&00)": Deletion not permitted
Meaning
The Release of the Route (&00) will not be executed
because the route is used by IPSEC
BCA07ED
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07ED ROUTE "(&00)" is no (&01) route
BCA07EE
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07EE ROUTE "(&00)": (&01) command running
BCA07EF
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07EF PROCESSOR "(&00)": Routes existing
BCA07E0
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07E0 "(&00)" already used as PROCESSOR-NAME
BCA07E1
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07E1 "(&00)" already used as ROUTE-NAME
BCA07E2
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07E2 "(&00)" already used as LINE-NAME
BCA07E3
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07E3 "(&00)" already used as NODE-NAME
BCA07E4
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07E4 "(&00)" already used as HOST-NAME
BCA07E5
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07E5 "(&00)" already used as DEVICE-NAME
BCA07E7
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA07E7 "(&00)" already used as AGGREGATION-NAME
BCA07F0
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA07F0 ABNORMAL TASK TERMINATION OF BCAM TASK "B C A M"
Meaning
Abnormal task termination of the BCAM task with TSN "BCAM".
Response
Take dump.
BCA07F1
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA07F1 ABNORMAL TASK TERMINATION OF BCAM TASK "B C A T"
Meaning
Abnormal task termination of the BCAM task with TSN "BCAT".
Response
Take dump.
BCA0702
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA0702 TRACE "(&00)" NOT INITIALIZED
Meaning
The initialization for the trace (&00)
has not been successful.
BCA0703
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0703 BCAM "(&00)" ACTIVE
Meaning
The BCAM task was successfully initialized.
BCAM version (&00) is active.
BCA071B
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA071B DCOPT MISSING AS FIRST COMMAND IN SOF FILE
Meaning
No DCOPT-Command given or the DCOPT-Command
is not the first command in the SOF-File.
Response
Correct the SOF-File and retry.
BCA071C
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA071C NAME OF HOST SPECIFIED NEITHER IN /DCSTART NOR IN /DCOPT COMMAND
Meaning
The name of the processor node in which BCAM is started was neither
specified in the /DCSTART nor in the /DCOPT command contained in the SOF.
Response
Restart BCAM using a corrected /DCSTART command or with a corrected SOF
after the termination message of BCAM.
BCA071F
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA071F BCAM "(&00)" DOESN'T FIT TO BS2000 "(&01)"
Meaning
The BCAM version (&00) does not fit to the BS2000 version (&01).
Reason: erroneous BS2000 system generation.
Response
Generate the BS2000 system with the correct BCAM.
BCA0715
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA0715 THE APPLICATION (&00) COULD NOT BE ENABLED
Meaning
The application (&00) needed for the internal processing of the BCAM task
could not be created.
Response
Call the system administrator.
BCA0716
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA0716 BCAM TERMINATED
Meaning
BCAM has been terminated.
Response
BCAM can be restarted after this message has been issued.
BCA0719
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA0719 Transport task TERMINATED
Meaning
A BCAM transport task has been terminated.
Response
The transport task will be restarted automatically.
BCA0720
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0720 HOST "(&00)" CREATED
Meaning
Host has been created.
(&00) = Name of the Host
BCA0728
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0728 HOST "(&00)" NOT CREATED
Meaning
The Host has not been created.
(&00) = Name of the Host
BCA0730
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0730 SHOW-ROUTE COMMAND PROCESSED
Meaning
BCAM command SHOW-ROUTE ended.
All information on selected routes are shown.
BCA0731
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0731 SHOW-BCAM-ATTRIBUTES COMMAND PROCESSED
Meaning
BCAM command SHOW-BCAM-ATTRIBUTES ended.
All selected information are shown.
BCA0740
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0740 PROG OR TASKEND PROCESSING COMPLETED
Meaning
The program or task end processing for the task in question has been
completed. Under normal circumstances this should not occur, as it
indicates that the task (program) after its termination processing
was still enabled as BCAM. Taskend processing is activated for each
such application of BCAM. In this way the task is automatically
disabled by force with respect to BCAM and name manager.
BCA0750
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0750 FILE "(&00)" IS NOW ACTIVE
Meaning
The content of file (&00) is read in and now used by BCAM.
BCA0751
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0751 BCAM FILE SERVICE started
Meaning
The BCAM FILE SERVICE was started.
BCA0752
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0752 BCAM FILE SERVICE terminated
Meaning
The BCAM FILE SERVICE was terminated.
BCA0758
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0758 INFO READY
Meaning
The INFO task was successfully initialized. INFO is ready.
BCA0759
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0759 INFO PROCESSING TERMINATED
Meaning
The INFO task was terminated.
BCA076A
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA076A ERROR "(&01)" AT COMMAND /(&00)
Meaning
The command handling of the command (&00) reported the error (&01).
(&01): Error identifier
= 0101 Parameter APPL invalid.
= 0201 Parameter HOST invalid.
= 0301 Parameter TSEL invalid.
= 0401 Parameter PTSEL invalid.
= 0501 Parameter ES invalid.
= 0601 Parameter FUNCT invalid.
= 0701 Parameter FILE invalid.
= 0801 Parameter MAXMAP invalid.
= 0901 Parameter SUBFUNCT invalid.
= 0A01 Parameter NAME invalid.
= 0F01 Parameter ROUTE invalid
= 1001 Parameter L3-CUD invalid.
= 1501 Parameter OPORT# invalid.
= 1601 Parameter PPORT# invalid.
= 0002 Object not found.
= 0003 name already defined.
= 0004 NAME already defined.
= 0005 global name already defined.
= 0007 mapping for NAME already existing.
= 0008 TSEL-N/TSEL-I/OPORT# inconsistent.
= 0009 PTSEL-N/PTSEL-I/PPORT# inconsistent.
= 000A mapping not allowed for ES.
= 000B TSEL-N/TSEL-I/OPORT# not free.
= 0010 Mapping function already initialized.
= 0011 Mapping function not initialized.
= 0020 DMS error occurred.
= 0021 no memory available or the maximum of allowed
mapping entries definded by MAXMAP is reached.
= 0022 (internal) error occurred.
Response
Enter corrected command.
BCA076C
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA076C (&00) cmd ignored
Meaning
Command (&00) has been ignored.
BCA076D
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA076D COMMAND /(&00) no longer supported
Meaning
command (&00) no longer supported.
Response
Do not use the command any more.
BCA076E
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA076E START PROCESSING ABORTED AT LOCATION (&00)
BCA076F
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA076F TIMEOUT FOR COMMAND (&00)
BCA0760
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0760 (&00) IN PROGRESS. /(&01) REJECTED
Meaning
The command /(&01) is rejected because
the command (&00) is running.
Response
Repeat command after termination of running command.
BCA0762
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0762 /(&00)/NAK
Meaning
The BCAM command (&00) couldn't be performed.
Response
The reason is already acquainted.
BCA0763
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0763 /(&00)/ACK
Meaning
Processing for the command (&00) is terminated without errors.
BCA0764
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0764 /(&00)/REJ
Meaning
The BCAM command (&00) is rejected.
The command is terminated.
Response
The reason is already acquainted.
BCA0765
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0765 /(&00)/ACC
Meaning
The command (&00) is accepted for processing.
BCA0766
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0766 BCAM NOT ACTIVE
Meaning
The command is only accepted if BCAM has been initialized.
BCA0767
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0767 Command (&00) in progress
BCA0768
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA0768 SYNTACTICAL ERROR IN COMMAND /(&00)
Meaning
Syntactical error in command (&00).
Response
Enter corrected command.
BCA0769
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0769 (&00) cmd syntactically correct
Meaning
Command (&00) is syntactically correct.
BCA077A
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA077A DEFINITION OF ROUTE "(&02)" TO PROCESSOR "(&00)" INVALID: (&01)
Meaning
The definition of the route (&02) to the processor (&00) is invalid.
The reason is given by (&01).
Reason = 03 No node attached to the route leading via a LAN
= 06 More than 1 socket hostname defined for the processor
= 09 Partner net address not given
= 0B More than 1 LAN address to 1 LAN adapter
= 0C No Line is assigned to this Route
= 0D More than 32 Routes to 1 Processor
= 16 Own ISO internet address missing
= 17 Own IP address missing
= 22 L3 profile wrong
= 25 router route has no fitting L3 profile
= 34 Own LAN address missing
= 36 LAN address is a broadcast/multicast address
= 37 IP address is a broadcast address
= 38 IP address is a loopback address
= 39 IP address type is not supported
= 43 Address already exists
= 49 Own IPV6 address missing
= 50 Automatic route modification active
= 51 no fitting IPV6 addressed route found
= 52 old IPV6 address missing
= 54 IPV6 not supported
= 56 same lines for route pair between virtual hosts
= 57 partner address belongs to same host
= 58 partner address = own address
= 59 IPv6 address is a IPV4 mapped address
= 60 IPv6 address is a Multicast address
= 61 IPv6 address is a Loopback address
= 62 IPv6 address type not supported
= 63 new name used for already existing processor
= 64 IP/IPv6 pair of addresses exists, check line and own-addr
BCA077B
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA077B Invalid parameter LAN-ADDRESS if parameter AGGREGATION-NAME is given
Meaning
LAN-ADDRESS=*DYNAMIC is valid if parameter AGGREGATION-NAME is given.
Response
Correct the command and retry.
BCA0770
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA0770 PARAMETER (&00) IS INVALID: (&01)
Meaning
The parameter (&00) is invalid.
The reason is given by (&01) or it is clear.
reason = 02 route processor not found
= 03 route processor is no NODE route
= 04 ADD- not concurrently with REMOTE-IP-NET possible
= 05 ADD- not concurrently with REMOTE-ISO-NET possible
= 07 name already exists
= 08 name not given
= 09 address not specified
= 10 ROUTE parameter not specified
= 11 first device mnemonic in DEV parameter not specified
= 12 second device mnemonic in DEV parameter not specified
= 13 MAXTSDU exceeds maximum
= 14 MAXTSDU exceeds minimum
= 15 L4 profile has to be ISO4 or TCP
= 16 own ISO internet address missing
= 17 own IP address missing
= 18 host not found
= 19 not defined as default router
= 20 not defined as router for specified address
= 22 L3 profile wrong
= 23 L3 and L4 profile do not fit
= 25 route with fitting L3 profile not found
= 26 LINE and ROUTE parameter do not fit
= 27 OLD-IPADR parameter not specified
= 28 OLD-INTADR parameter not specified
= 29 OLD-LANADR parameter not specified
= 30 fitting route with ISO internet addressing not found
= 31 fitting route with LAN addressing not found
= 32 fitting route with IP addressing not found
= 33 route processor must not be the processor itself
= 34 own LAN address missing
= 36 LAN address is a broadcast/multicast address
= 37 IP address is a broadcast address
= 38 IP address is a loopback address
= 39 IP address type is not supported
= 40 shortage of system memory (class 5)
= 42 another address is already defined
= 43 address already exists
= 45 no single route specified
= 46 route does not lead to specified processor
= 47 upper IP address less than lower one
= 48 PATH not simultaneously with other parameter possible
= 49 own IPV6 address missing
= 50 automatic route modification active
= 51 no fitting IPV6 addressed route found
= 52 old IPV6 address missing
= 53 processor is not local attached to the LAN
= 54 IPV6 not supported
= 55 PATH=*VIA-ROUTE not specified
= 56 same lines for route pair between virtual hosts
= 57 partner address belongs to same host
= 58 partner address = own address
= 59 IPv6 address is a IPV4 mapped address
= 60 IPv6 address is a Multicast address
= 61 IPv6 address is a Loopback address
= 62 IPv6 address type not supported
= 63 new name used for already existing processor
= 64 IP/IPv6 pair of addresses exists, check line and own-addr
= 65 L3 profile not allowed over VLAN
= 66 already defined as default router
= 67 Router has a different own address
= 68 already defined as router
= 69 must not be router for itself
= 70 LINK-LOCAL IPv6 address is no router address
= 71 L3 Profil fehlt
= 72 L2 Profil fehlt
Response
Correct the command and retry.
BCA0771
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA0771 ERROR (&00) IN LINE (&01) OF FILE "(&02)"
Meaning
Line (&01) of file (&02) doesn't fit the conventions:
(&02) defines the file name or : "SOCKETHOST-TABLE" ,
"PROCESSOR-TABLE", "FQDN-TABLE", "SERVICES-TABLE",
or "APPLICATION-TABLE" (see command DCSTART).
(&00) defines the error:
1 = shortage of memory when reading the file
2 = more lines in file than allowed
3 = line length erroneous
4 = "address type" erroneous
5 = "processor name" erroneous
6 = "sockethost name" erroneous
7 = "IP/IPv6 address" erroneous
8 = "ISO8473 address" erroneous
9 = "IP/IPv6/ISO8473 address" double within the file
10 = "processor/sockethost/application name" double within the file
11 = invalid syntax
12 = invalid "service name"
13 = invalid "ProtoPort"
14 = no "service name"
15 = too many "service alias names"
16 = "FQDN" invalid
A = "address inconsistency" to processor-table in file
detected
B = "name type" erroneous (neither "NEA" nor "ISO")
C = "NEA application name" erroneous
D = "ISO application name" erroneous
E = "SOCKETS USERID" erroneous
F = "host name" erroneous
20 = other error
Response
Correct the file
BCA0772
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA0772 (&00) ERRORS OF TYPE (&01) IN FILE "(&02)" DETECTED
Meaning
There are (&00) errors with message number (&01) detected
during reading of file (&02).
Not all incorrect statements are protocolled separately.
Response
Correct the file
BCA0773
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA0773 Invalid DATA TYPE for "(&00)"
Meaning
Invalid DATA TYPE given for the parameter (&00).
Response
Correct the command and retry.
BCA0774
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA0774 OWN-(&00)-ADDRESS missing
Meaning
Own address of type "(&00)" is undefined.
Response
Correct the command and retry.
BCA0775
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA0775 (&00)-ADDRESS missing
Meaning
Address of type "(&00)" is undefined.
Response
Correct the command and retry.
BCA0776
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA0776 (&00) interface used at (&01) for (&02); Exhausted at used slots: (&03)
Meaning
The system function (&00) was used at address (&01) for (&02). The
returncode "exhausted" was obtained at used slots (&03).
there means:
(&00): function causing the error
(&01): Address of call to the function
(&02): resource
(&03): usage
BCA0777
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA0777 (&00)-INTERFACE USED AT (&01) FOR (&02); RC: (&03)
Meaning
The system function (&00) was used at address (&01) for (&02). The
returncode (&03) was obtained.
there means:
(&00): function causing the error
(&01): Address of call to the function
(&02): resource
(&03): returncode of function
meaning of function and resource:
(&00) (&02) meaning
---------------------------------------------------------------
<DMS macro> <file> DMS macro call with file name as parameter
DMS-OPEN RDF open RDF (resource definition file)
DMS-OPEN SOF open SOF (start option file)
DMS-OPEN CMD-FILE open BCAM command file
CATJV STA-JV catalog a status-JV
ERAJV STA-JV erase a status-JV
SETJV STA-JV set a status-JV
STAJV STA-JV information to a status-JV
RDUID GET-USER get user-ID
$SATBCM BAO-SUCC TSAP open successful
$SATBCM BAO-FAIL TSAP open failure
$SATBCM BAC-SUCC TSAP close successful
$SATBCM BAC FAIL TSAP close failure
$SATBCM BCN-SUCC Connection open successful
$SATBCM BCN-FAIL Connection open failure
$SATBCM BDS-SUCC Connection close successful
$SATBCM BDS-FAIL Connection close failure
$SATIPS ILD-SUCC Load IPSEC database successful
$SATIPS ILD-FAIL Load IPSEC database failure
$SATIPS IPV IPSEC security policy threat
$SETPRV SETPRIV set "TSOS" privilege
$SETPRV RSETPRIV reset "TSOS" privilege
$SRMREQ CREAPRIV create task privilege "TSOS"
$TSNCHA <tsn> change the TSN
$TSNGET <tid> get TSN for given TID (&02)
$TSNINF <tsn> get TID for given TSN (&02)
$TSNNFR <tsn> get the next free TSN (&02) from system
BCA0778
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA0778 (&00) interface used at (&01) for (&02); Rc: (&03), Id: (&04), Slot: (&05)
Meaning
The system function (&00) was used at address (&01) for (&02). The
returncode (&03) was obtained. (&04) was the slot id, (&05) the
slot address.
There means:
(&00): function causing the error
(&01): Address of call to the function
(&02): resource
(&03): returncode of function
(&04): slot id
(&05): address of slot
BCA079A
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA079A IPv6 LINK LOCAL ADDRESS not allowed in command
BCA079E
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA079E (&00) ADDRESS "(&01)" not allowed. Reason: "(&02)"
Meaning
(&00) : address type
= IP
= IPV6
(&01) : typed address
(&02) : reason
= FIREWALL
BCA079F
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA079F (&00) ADDRESS "(&01)" UNKNOWN
Meaning
(&00) : address type
= IP
= IPV6
= LAN
= ISO
(&01) : typed address
BCA0790
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA0790 APPLICATION GROUP "(&00)" UNKNOWN
BCA0791
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA0791 APPLICATION "(&00)" UNKNOWN
BCA08AB
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA08AB ROUTE "(&00)" : ENDSYSTEM=(&01),VLAN-LINE=(&02),LINK-AGGREGATION=(&03), VLAN-ID=(&04)
Meaning
the state of the route will be displayed
(&00) name of the route
(&01) name of endsystem
(&02) name of the VLAN-LINE
(&03) name of the LINK-AGGREGATION
(&04) value of the VLAN-ID
BCA08AE
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA08AE ROUTE "(&00)" : ROUTER=(&01),STATE=(&02),TRANSFER=(&03),TYPE=((&04),(&07)), MAX-NSDU=(&05),MAX-TSDU=(&06)
Meaning
The state of the route will be displayed
(&00) name of the route
(&01) name of the router
(&02) administrative status
= ACTIVE route is administrative active
= INACTIVE route is administrative inactive
= EXCLUDED route is administrative excluded
(&03) transfer state
= WAIT-FOR-INIT route is not used
= WAIT-FOR-READY routing protocol is in process
= NOT-READY route is not ready
= READY route is working
(&04) type of route
= NODE
= REMOTE
(&05) maximum NSDU length
(&06) maximum TSDU length
(&07) type of using of the route
= ISO/IP ROUTER
= FIREWALL-ENTRY
= SERVER-PORT-ACCESS
= REMOTE-SERVER-PORT-ACCESS
= TRANSON-SERVER
= MULTICAST
BCA08AF
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA08AF ROUTE "(&00)" : ENDSYSTEM=(&01),VLAN-LINE=(&02),VLAN-DEVICE=(&03), VLAN-ID=(&04)
Meaning
the state of the route will be displayed
(&00) name of the route
(&01) name of endsystem
(&02) name of the VLAN-LINE
(&03) name of the VLAN-DEVICE
(&04) value of the VLAN-ID
BCA08A1
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA08A1 Connection (CON#=x'(&00)'): Application=(NAME=(&01)/TSEL=(&02)/HOST=(&03)); SAVE=(&04)
Meaning
(&00) : unique number for the connection
(&01) : application name formatted as (<type>,<string>)
(&02) : transport selector of application formatted as (<type>,<string>)
(&03) : host name
(&04) : NO connection is not saved
LOCAL connection is saved locally
BCA08A2
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA08A2 Connection (CON#=x'(&00)'): Partner=(NAME=(&01)/TSEL=(&02)/ES=(&03)/ROUTE=(&04));PROT=(&05), IPSEC=(&06),VLAN=(&07)
Meaning
(&00) : unique number for the connection
(&01) : partner name formatted as (<type>,<string>)
(&02) : transport selector of partner formatted as (<type>,<string>)
(&03) : name of partner endsystem
(&04) : name of route or *LOOPBACK
(&05) : transport protocol
(&06) : NO connection is not secured via IPSEC
YES connection is secured via IPSEC
(&07) : NO connection does not lead via VLAN
n connection leads via VLAN with VLAN-ID n
BCA08A6
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA08A6 ROUTE "(&00)" : ENDSYSTEM=(&01),PROFILE=((&02),(&03),(&04)), NETADDRESS=((&05),(&06))
Meaning
the state of the route will be displayed
(&00) name of the route
(&01) name of endsystem
(&02) layer 4 profile
= ISO4
= TCP
(&03) layer 3 profile
= INTF
= IP
= IPV6
(&04) layer 2 profile
= LLC1
= ETHERNET
= SNAP
= LAN
(&05) own netaddress
(&06) partner netaddress
BCA08A7
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA08A7 Local Connection (CON#=x'(&00)'): Application=(NAME=(&01)/TSEL=(&02)/HOST=(&03)); SAVE=(&04)
Meaning
(&00) : unique number for the connection
(&01) : application name formatted as (<type>,<string>)
(&02) : transport selector of application formatted as (<type>,<string>)
(&03) : host name
(&04) : NO connection is not saved
LOCAL connection is saved locally
BCA08A8
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA08A8 Local Connection (CON#=x'(&00)'): Partner=(NAME=(&01)/TSEL=(&02)/PARTNERHOST=(&03))
Meaning
(&00) : unique number for the connection
(&01) : partner name formatted as (<type>,<string>)
(&02) : transport selector of partner formatted as (<type>,<string>)
(&03) : name of partner host
BCA08BA
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA08BA Command "(&00)" is not allowed from a Command File
Meaning
BCAM SDF command (&00) can not be started from a command file or SOF.
Response
Retry the command after termination of the current command file or the
SOF.
BCA08B0
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA08B0 COMMAND FILE OR SOF IN PROCESS
Meaning
Another command file or the SOF is currently in process.
Response
Retry the command after termination of the current command file or the
SOF.
BCA08B1
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA08B1 TOO MANY BRANCH INSTRUCTION LEVELS IN COMMAND FILE
Meaning
Maximal 8 levels of branch instructions (IF-BCAM-ACK,IF-BCAM-NAK,
ELSE-BCAM,END-IF-BCAM) are permitted in a command file or in SOF .
Response
Correct command file or SOF and restart.
BCA08B2
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA08B2 BRANCH INSTRUCTION /IF-BCAM- IS MISSING IN COMMAND FILE
Meaning
A branch instruction /ELSE-BCAM or /END-IF-BCAM was read.
The corresponding instruction /IF-BCAM-ACK or /IF-BCAM-NAK is missing.
Response
Correct command file or SOF and restart.
BCA08B3
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA08B3 Branch instruction /IF-BCAM-HOST is missing in COMMAND FILE
Meaning
A branch instruction /END-IF-BCAM-HOST was read.
The corresponding instruction /IF-BCAM-HOST is missing.
Response
Correct command file or SOF and restart.
BCA08B4
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA08B4 Branch instruction /IF-BCAM-SYSINF is missing in COMMAND FILE
Meaning
A branch instruction /END-IF-BCAM-SYSINF was read.
The corresponding instruction /IF-BCAM-SYSINF is missing.
Response
Correct command file or SOF and restart.
BCA08B5
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA08B5 HOST-NAME not specified in /DCSTART command
Meaning
The name of the processor node in which BCAM is started was not
specified in the /DCSTART command.
Response
Restart BCAM using a corrected /DCSTART command
after the termination message of BCAM.
BCA08B6
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA08B6 Too many HOST branch instruction LEVELS in COMMAND FILE
Meaning
Maximal 1 level of HOST branch instructions (IF-BCAM-HOST,
END-IF-BCAM-HOST) is permitted in a command file or in a SOF.
Response
Correct command file or SOF and restart.
BCA08B7
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA08B7 Too many SYSINF branch instruction LEVELS in COMMAND FILE
Meaning
Maximal 1 level of SYSINF branch instructions (IF-BCAM-SYSINF,
END-IF-BCAM-SYSINF) is permitted in a command file or in a SOF.
Response
Correct command file or SOF and restart.
BCA08CA
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA08CA VLAN-LINE "(&00)": DUPLICATE-Address "(&01)" received from "(&02)" !!!
Meaning
The OWN IP/IPv6 address (&01) at VLAN-line (&00)
was received from MAC address (&02).
BCA08CB
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA08CB IP-SUBNET : NODE "(&00)",STATE=(&01),IP-SUBNET-MASK=(&02)
Meaning
An IP-SUBNET will be displayed
(&00) name of the according node
(&01) status
= WAIT-FOR-EXTENSION AR-CACHE extension is in process
(&02) Mask for IP-subnet-address
BCA08CF
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA08CF /BCSWP (&00) PROCESSED
Meaning
The /BCSWP command is executed for (&00).
BCA08C5
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA08C5 MULTICAST LIST EXHAUSTED FOR LINE "(&00)"; ADDRESS (&01) INOPERABLE
Meaning
The Multicast slot necessary for working of the address can not be
loaded into the device because of hardware restrictions.
Response
Use a different line with an wider multicast list.
BCA08C7
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA08C7 LINE "(&00)": Address "(&01)" is DUPLICATE to "(&02)"
Meaning
The IP/IPv6 address (&01) at line (&00)
was checked as duplicate to MAC address (&02)
and set invalid.
BCA08C8
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA08C8 LINE "(&00)": DUPLICATE-Address "(&01)" received from "(&02)" !!!
Meaning
The OWN IP/IPv6 address (&01) at line (&00)
was received from MAC address (&02).
BCA08C9
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA08C9 VLAN-LINE "(&00)": Address "(&01)" is DUPLICATE to "(&02)"
Meaning
The IP/IPv6 address (&01) at VLAN-line (&00)
was checked as duplicate to MAC address (&02)
and set invalid.
BCA08DA
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA08DA PROCESSOR "(&00)" ALREADY DEACTIVATED
Meaning
Processor (&00) is not active. Command /BCDAC not necessary.
BCA08DE
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA08DE ROUTE "(&00)" TO PROCESSOR "(&01)" ACTIVE
BCA08DF
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA08DF "(&00)" ACTIVE
Meaning
(&00) is set active in the internal BCAM tables.
(&00) is a processor or an application group.
BCA08D0
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA08D0 LINE "(&00)" ALREADY DEACTIVATED
Meaning
Line (&00) is not active. Deactivation is not necessary.
BCA08D1
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA08D1 HOST "(&00)" ACTIVE
Meaning
Virtual Host (&00) is accessible. Message transfer is possible to
partners.
BCA08D2
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA08D2 NODE "(&00)" ACTIVE
Meaning
LAN node (&00) is accessible. Message Transfer is possible to
partners.
BCA08D3
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA08D3 HOST "(&00)" NOT ACTIVE
Meaning
Virtual Host (&00) was not yet activated by /BCACT.
Response
Activate the Virtual Host (&00) by /BCACT.
BCA08D4
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA08D4 NODE "(&00)" NOT ACTIVE
Meaning
LAN node (&00) was not yet activated by /BCACT.
Response
Activate the LAN node (&00) by /BCACT.
BCA08D5
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA08D5 HOST "(&00)" DEACTIVATED
Meaning
Virtual Host (&00) was deactivated by /BCDAC.
Existing connections are stopped but remain.
BCA08D6
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA08D6 NODE "(&00)" DEACTIVATED
Meaning
LAN node (&00) was deactivated by /BCDAC.
Existing connections are stopped but remain.
BCA08D7
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA08D7 "(&00)" ALREADY ACTIVE
Meaning
(&00) is already active.
BCA08D9
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA08D9 ROUTE "(&00)" ALREADY DEACTIVATED
Meaning
Route (&00) is not active. Command /BCDAC not necessary.
BCA08EA
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA08EA ENDSYSTEM "(&00)" : STATE=(&01),TYPE=(&02),MAX-TSDU=(&03),SOCKETHOST=(&04)
Meaning
The state of the endsystem will be displayed
(&00) name of endsystem
(&01) administrative status
= ACTIVE endsystem is administrative active
= INACTIVE endsystem is administrative inactive
= EXCLUDED endsystem is administrative excluded
(&02) type of endsystem
= HOST/BCAM endsystem is a HOST
= HOST/? another type of endsystem
(&03) maximal TSDU size
(&04) sockethost name of endsystem
BCA08EB
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA08EB NODE "(&00)" : STATE=(&01),IP-SUBNET-MASK=(&02),LAN-TYPE=(&03)
Meaning
The state of the node will be displayed
(&00) name of node
(&01) administrative status
= WAIT-FOR-ACTIVATION activation of node is in process
= WAIT-FOR-DEACTIVATION deactivation of node is in process
= ACTIVE node is administrative active
= INACTIVE node is administrative inactive
= EXCLUDED node is administrative excluded
(&02) Mask for IP-subnet-address
(&03) lan type
= *NORMAL normal lan
= *VIRTUAL virtual lan
BCA08EC
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA08EC NODE "(&00)" : STATE=(&01),IP-SUBNET-MASK=(&02),LAN-TYPE=(&03), NODE-TYPE=(&04)
Meaning
The state of the node will be displayed
(&00) name of node
(&01) administrative status
= WAIT-FOR-ACTIVATION activation of node is in process
= WAIT-FOR-DEACTIVATION deactivation of node is in process
= ACTIVE node is administrative active
= INACTIVE node is administrative inactive
= EXCLUDED node is administrative excluded
(&02) Mask for IP-subnet-address
(&03) lan type
= *NORMAL normal lan
= *VIRTUAL virtual lan
(&03) node type
= *NORMAL normal node
= *CONTROL control node
BCA08ED
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA08ED LINE "(&00)" : STATE=(&01),TRANSFER=(&07),PROFILE=(&02), DEVICE=(WRITE=(&03),READ=(&04),DIAG=(&05)),MAX-LSDU=(&06)
Meaning
The state of the line will be displayed
(&00) name of the line
(&01) administrative status
= ACTIVE line is administrative aktiv
= INACTIVE line is administrative inaktiv
= EXCLUDED line is excluded
(&02) transfer procedure
= CSMACD link protocol for CSMA/CD mode
(&03) mnemonic line name for write
(&04) mnemonic line name for read
(&05) mnemonic line name for diagnosis
(&06) maximum LSDU length
(&07) transfer state
= WAIT-FOR-ACTIVATION activation is in process
= WAIT-FOR-DEACTIVATION deactivation is in process
= NOT-READY-TO-OPERATE line is not yet ready to work
= WORKING line is active
= NONE line is not yet activated
BCA08EE
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA08EE ROUTE "(&00)" : ENDSYSTEM=(&01),STATE=(&02),TRANSFER=(&03),TYPE=((&04), (&07)),MAX-NSDU=(&05),MAX-TSDU=(&06)
Meaning
The state of the route will be displayed
(&00) name of the route
(&01) name of endsystem
(&02) administrative status
= ACTIVE route is administrative active
= INACTIVE route is administrative inactive
= EXCLUDED route ist administrative excluded
(&03) transfer state
= WAIT-FOR-INIT route is not used
= WAIT-FOR-READY routing protocol is in process
= NOT-READY route is not ready
= READY route is working
(&04) type of route
= NODE
= REMOTE
(&05) maximum NSDU length
(&06) maximum TSDU length
(&07) type of using of the route
= ISO/IP ROUTER
= FIREWALL-ENTRY
= SERVER-PORT-ACCESS
= REMOTE-SERVER-PORT-ACCESS
= TRANSON-SERVER
= MULTICAST
BCA08EF
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA08EF NOTHING TO SHOW FOUND
BCA08E0
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA08E0 HOST "(&00)" : STATE=(&01),TYPE=(&02),MAX-TSDU=(&03)
Meaning
The state of the host will be displayed
(&00) name of the host
(&01) administrative status
= ACTIVE host is administrative active
= INACTIVE host is administrative inactive
= EXCLUDED host ist administrative excluded
(&02) type of host
= NORMAL
= VIRTUAL
(&03) maximum TSDU length
BCA08E1
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA08E1 BCAM: VERSION (&00), PVLU (&01), LOADER (&02)
BCA08E2
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA08E2 APPLICATION (&00) IN (&01): TSN=(&02), TID=(&03)
Meaning
The application (&00) in the host (&01) has been enabled by the task with
TSN (&02), TID (&03).
BCA08E5
Destination: CONSOLE Routing code: C Weight: 70
Warranty : YES
BCA08E5 "(&00)" UNKNOWN
Meaning
The object "(&00)" is unknown. The type of the object
is defined by the corresponding command.
BCA08E6
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA08E6 ROUTE "(&00)" : ENDSYSTEM=(&01),PROFILE=((&02),(&03),(&04)), NETADDRESS=((&05),(&06)),LINE=(&07)
Meaning
the state of the route will be displayed
(&00) name of the route
(&01) name of endsystem
(&02) layer 4 profile
= ISO4
= TCP
(&03) layer 3 profile
= INT0
= INTF
= IP
= IPV6
(&04) layer 2 profile
= LLC1
= ETHERNET
= SNAP
= LAN
(&05) own netaddress
(&06) partner netaddress
(&07) name of the line
BCA08E7
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA08E7 APPLICATION (APP#=X'(&02)'): NAME=(&00)/HOST=(&01), PORT#=(&08), TASKS=(&03), CONNECTIONS=(&04), GROUP=(&05), FUNCT=(&06), SHARE=(&07)
Meaning
(&00) : application name formatted as (<type>,<string>)
(&01) : host name
(&02) : unique number for the application
(&03) : number of tasks having enabled the application
(&04) : number of connections of this application
(&05) : name of application group this application belongs to or "-"
(&06) : functionality of interface (NEA/ISO/STREAMS)
(&07) : The application may be opened by several task (YES) or by only one
(&08) : Port-# used by application
BCA08E8
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA08E8 Connection (CON#=X'(&00)'): PROT=(&01), DATA=(I=X'(&02)',O=X'(&03)'), TRANSFER=(&04), MEMORY=(I=(&05),O=(&06))
Meaning
(&00) : unique number for the connection
(&01) : transport protocol
(&02) : data bytes received by the application on this connection
(&03) : data bytes sent by the application on this connection
(&04) : data transfer in protocol entity is possible (YES) or stopped (NO)
(&05) : used data buffer in bytes for input data not yet received by the
application
(&06) : used data buffer in bytes for output data not yet transferred to
the partner
BCA08F0
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA08F0 OWN ALIASHOST = (&00) / PARTNER ALIASHOST = (&01)
Meaning
(&00) : own aliashostname
(&01) : partner aliashostname
BCA08F4
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA08F4 IP-RANGE: (&00)
Meaning
Display of IP-RANGES.
BCA08F5
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA08F5 REMOTE-SERVER-PORTS: (&00)
Meaning
The remote server ports are displayed.
BCA08F6
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA08F6 TIMER PERIODS FOR ROUTE "(&00)" OF PROCESSOR "(&01)": WINDOW=(&02), RETRANSMISSION=(&03),AK=(&04),REJECT=(&05),ERROR-RECOVERY=(&06), EXP-RETRANSMISSION=(&07)
Meaning
The route specific times are displayed.
BCA08F7
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA08F7 TIMER PERIODS: WARNING=(&00), CONNECTION=(&01), INPUT LETTER=(&02), INPUT DATAGRAM=(&08), CONFIGURATION=(&04), IP=(&05), ISO8473=(&06), NET REASSEMBLY=(&07) (&03) (&09)
Meaning
The global times are displayed.
The value 'INFINITE' for the letter arrival period
means that this timer has not yet been started.
BCA08F8
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA08F8 MEM-PAG: (&05)KB, MEM-RES: (&04)KB, DASTFA: (&03), MAXCNN: (&00), MAXNPA: (&01), MAXNPT: (&02), PRIVPORT#: (&06), FREEPORT#: (&07), MAX-ISAM-POOL-SIZE: (&08)
Meaning
The maximum size of the resident and pageable data pool and the values
MAXCNN, MAXNPA, MAXNPT, DASTFA, FREEPORT#, PRIVPORT# and
MAX-ISAM-POOL-SIZE, set by /DCSTART or /BCMOD command, are displayed.
(DASTFA = historical, but yet supported)
BCA08F9
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA08F9 SERVER-PORTS: (&00)
Meaning
The server ports are displayed.
BCA0801
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA0801 ILLEGAL FILE NAME "(&00)"
Meaning
syntax error in file name.
BCA0802
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA0802 FILE NAME ERROR, (&00) "(&01)" SAME AS (&02) "(&03)"
Meaning
Same file names not permitted.
Checked file names :
Processor Table
FQDN Table
Sockethost Table
Services Table
Application Table.
BCA0810
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0810 BCAM ALREADY ACTIVE
Meaning
A /DCSTART command must not be issued before the BCAM task created by
a previously issued /DCSTART command is destroyed, i. e. before the
message BCAM PROCESSING TERMINATED has been issued.
BCA0814
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0814 BCAM ABNORMALLY TERMINATING
Meaning
The BCAM task is abnormally terminating.
Response
Reply the command as soon as BCAM has been terminated.
BCA0815
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0815 BCAM ALREADY STARTING
Meaning
DCSTART command already in progress.
BCA0816
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0816 BCAM IS SHUTTING
Meaning
Wait with /DCSTART - command until shutting of BCAM is finished.
BCA082A
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA082A (&00) ALREADY INCLUDED
Meaning
(&00) is already included.
BCA082B
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA082B RDF DSECTS INCOMPATIBLE WITH BCAM DSECTS
Meaning
Incompatibility between RDF and BCAM modules, wrong RDF version.
Response
A new RDF must be generated.
BCA0825
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA0825 PARAMETER "HOST=(&00)" DOES NOT SPECIFY A BCAM HOST
Meaning
The specified segment in HOST parameter of /DCSTART is not a BS2000
segment.
Response
Check definitions, retry with correct name.
BCA083E
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA083E ROUTE "(&00)" TO PROCESSOR "(&01)" INCLUDED
Meaning
Route (&00) to processor (&01) was included in net description
by /BCIN.
BCA083F
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA083F (&00) INCLUDED
Meaning
(&00) has been included.
BCA0830
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0830 HOST "(&00)" INCLUDED
Meaning
Virtual Host (&00) was included in net description by /BCIN.
BCA0831
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0831 NODE "(&00)" INCLUDED
Meaning
LAN node (&00) was included in net description by /BCIN.
BCA0832
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA0832 PACKET LENGTH FOR LINK PROCEDURE TOO SMALL ON LINE "(&00)". STANDARD TAKEN
Meaning
The packet length from or to a directly connected processor has been
generated too small. The standard value is taken.
Response
Correct the generation.
BCA0833
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA0833 NAME (&00) ALREADY DEFINED
Meaning
The name (&00) is defined twice.
Response
Regenerate with unique names.
BCA0836
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA0836 MAXIMUM NUMBER OF LINES ALREADY DEFINED
Meaning
The maximum number of LINEs was reached.
BCA084A
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA084A (&00) "(&01)" SET TO "(&02)"
Meaning
BCAM operating parameter (&01) of the group (&00) is set to (&02).
BCA084B
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA084B "(&00)" IS ALREADY "(&01)"
Meaning
BCAM operating parameter (&00) was already set to (&01).
BCA084D
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA084D "(&00)" MONITORING STARTED WITH "(&01)" SECONDS
Meaning
(&00)-Monitoring was started,
the cycle time was set to (&01) seconds.
BCA084F
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA084F "(&00)" MONITORING STOPPED
Meaning
(&00)-Monitoring was stopped.
BCA0841
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0841 BROADCAST activated for LINE "(&00)"
Meaning
Broadcast mode was switched on for line (&00)
due to a former /BCOPTION or /MODIFY-LINE command.
BCA0842
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0842 BROADCAST deactivated for LINE "(&00)"
Meaning
Broadcast deactivated for line (&00)
due to a former /BCOPTION or /MODIFY-LINE command.
BCA0843
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0843 MULTICAST activated for LINE "(&00)"
Meaning
Multicast was activated for line (&00)
due to a former /BCOPTION or /MODIFY-LINE command.
BCA0844
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0844 MULTICAST deactivated for LINE "(&00)"
Meaning
Multicast was deactivated for line (&00)
due to a former /BCOPTION or /MODIFY-LINE command.
BCA0845
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0845 SLOW-POLL running on LINE "(&00)"
Meaning
Slow-Poll running on line (&00)
due to a former /BCOPTION or /MODIFY-LINE command.
BCA0846
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0846 SLOW-POLL stopped on LINE "(&00)"
Meaning
Slow-Poll was stopped on line (&00)
due to a former /BCOPTION or /MODIFY-LINE command.
BCA0847
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0847 CHECKSUM done by DEVICE for LINE "(&00)"
Meaning
Checksum done by DEVICE for LINE (&00)
due to a former /MODIFY-LINE command.
BCA0848
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0848 CHECKSUM done by BCAM for LINE "(&00)"
Meaning
Checksum done by BCAM for LINE (&00)
due to a former /MODIFY-LINE command.
BCA0849
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0849 "(&00)" CHANGED TO "(&01)"
Meaning
BCAM operating parameter (&00) was changed to (&01).
BCA085C
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA085C /BCOUT (&00),W=Y ALREADY GIVEN; CURRENT COMMAND REJECTED
Meaning
/BCOUT (&00),W=Y command was given twice.
Response
None; /BCOUT W=N can be used to remove the processor immediately.
BCA085D
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA085D HOST "(&00)" EXCLUDED
Meaning
Virtual Host (&00) was excluded from net configuration by /BCOUT.
He is no longer accessible. Existing connections are cancelled.
BCA085E
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA085E NODE "(&00)" EXCLUDED
Meaning
LAN node (&00) was excluded from net configuration by /BCOUT.
He is no longer accessible. Existing connections are cancelled.
BCA085F
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA085F (&00) EXCLUDED
Meaning
The processor or the application group (&00) is excluded.
BCA0850
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0850 WARNING ALREADY GIVEN; CURRENT COMMAND REJECTED
Meaning
A command with W=Y command was given twice.
Response
None.
BCA0852
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0852 PROCESSOR "(&00)" INACTIVE
Meaning
Processor (&00) was deactivated.
BCA0853
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0853 ROUTE "(&00)" TO PROCESSOR "(&01)" INACTIVE
Meaning
The route (&00) to processor (&01) was deactivated.
BCA0856
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA0856 (&00) NOT INCLUDED
Meaning
The object named (&00) could not be included.
BCA0857
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA0857 NAME OF RUNNING BCAM NOT ALLOWED IN THE COMMAND
Meaning
the command is not allowed for the running BCAM.
Response
To terminate BCAM, /BCEND command must be given.
BCA0858
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA0858 HOST "(&00)" NOT INCLUDED
Meaning
Virtual Host (&00) is not included in net description by /BCIN.
Response
Include the Virtual Host (&00) by /BCIN into the net description.
BCA086F
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA086F STATION (&00): DISCONNECTION FROM APPLICATION (&01) AFTER WARNING COMPLETED
Meaning
A connection is deleted after a /BCCONN command with warning has been
issued for it. Disconnection may have occurred by any possible reason.
BCA0862
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA0862 NO CONNECTION FOUND
Meaning
No connection has been found.
BCA0863
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0863 STATION (&00): DISCONNECTION FROM APPLICATION (&01) SUCCESSFUL
Meaning
The connection to (&00) has been destroyed.
BCA087A
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA087A BCAM MAPPING DEFINITION: APPL=(&00),HOST=(&01),TSEL=(NEA:(&02)/ISO: (&03)/PORT#:(&10));NAME=(&04),PTSEL=(NEA:(&05)/ISO:(&06)/PORT#:(&11)), ES=(&07);ROUTES=(&08);L3-CUD=(&09)
Meaning
the mapping-entry will be displayed:
(&00) name of application
(&01) name of host
(&02) name of own NEA-T-selector
(&03) name of own ISO-T-selector
(&10) own port-number
(&04) name of partner application
(&05) name of partner NEA-T-selector
(&06) name of partner ISO-T-selector
(&07) name of endsystem
(&11) partner port-number
(&08) name of routes maximal 8 name of routes
(&09) L3 call user data
BCA087C
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA087C BCAM NAME MAPPING ENTRIES EXIST FOR HOST: (&00)
Meaning
State of BCAM-mapping is shown :
(&00) name of host with existing mapping-entries
BCA0870
Destination: CONSOLE Routing code: C Weight: 30
Warranty : YES
BCA0870 STATE OF BCAM-MAPPING: MAXMAP=(&00), CURMAP=(&01), MAXQUEUE=(&02)
Meaning
State of BCAM-mapping is shown :
(&00) = maximum number of mapping entries
(&01) = actual number of mapping entries
(&02) = maximum length of queue
BCA088A
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA088A (&00) IS A SYSTEM APPLICATION
Meaning
The command is not allowed for system applications.
BCA088F
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA088F APPLICATION (&00) CLOSED
Meaning
Close processing for application (&00) is finished.
Response
None.
BCA089A
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA089A CONNECTION TO $CONSOLE REJECTED
Meaning
$CONSOLE rejects the connection request of BCAM.
Response
Check definitions. Enter commands of the command file at the operator
console.
BCA089B
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA089B CONNECTION TO $CONSOLE FAILED CAUSED BY INTERNAL SHORTAGE OF MEMORY
Meaning
Command file processing has gotten an internal shortage of slots
when trying to establish a connection to $CONSOLE.
Response
Probably enter commands of the command file at the operator console.
BCA089C
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA089C A COMMAND COULD NOT BE SENT TO $CONSOLE
Meaning
A command could not be sent to $CONSOLE.
BCA089D
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA089D COMMAND "(&00)..." TOO LONG
Meaning
The command "(&00)..." of the command file exceeds the maximal length.
Response
Correct the command file.
BCA089E
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA089E COMMAND FILE PROCESSING ABORTED
Meaning
Command file processing is terminated owing to an error.
The reason is given in the previous message.
Response
Remaining commands in the command file can be given via console.
BCA089F
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA089F SOF PROCESSING COMPLETED
Meaning
All commands of the SOF have been processed.
BCA0890
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0890 COMMAND FILE PROCESSING COMPLETED
Meaning
All commands of the command file have been processed.
BCA0891
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA0891 CONNECTION REQUEST TO $CONSOLE FAILED
Meaning
Connection to $CONSOLE could not be established.
Response
Probably enter commands of the command file at the operator console.
BCA0893
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA0893 SOF PROCESSING ABORTED
Meaning
SOF processing is terminated owing to an error.
The reason is given in the previous message.
Response
Remaining commands in the SOF can be given via console.
BCA0895
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA0895 DCOPT COMMAND MISSING
Meaning
The DCOPT command has to be the first command in the SOF file;
but it was not found.
Response
Correct the SOF file.
BCA0896
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA0896 command file is not accessible
Meaning
The command file may be migrated or may not exist.
Response
Make the migrated file accessible.
BCA0898
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA0898 TIMEOUT WHILE PROCESSING A COMMAND FILE
BCA0899
Destination: CONSOLE Routing code: C Weight: 70
Warranty : NO
BCA0899 NO NEXT COMMAND FILE ALLOWED
Meaning
There are 10 command files simultaneous in work.
BCA0910
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0910 ROUTE "(&00)" NOT READY TO OPERATE
BCA0911
Destination: CONSOLE Routing code: C Weight: 50
Warranty : NO
BCA0911 ROUTE "(&00)" READY TO OPERATE AGAIN
BCA0915
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0915 OSPF HELLO RECEIVED from ROUTER "(&00)" via ROUTE "(&01)"
Meaning
A OSPF protocol HELLO message was received from ROUTER (&00)
via ROUTE (&01).
Now BCAM knows the router (&00) via ROUTE (&01) and will use it
for automatic endsystem creation and as alternative router.
BCA0916
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA0916 OSPF HELLO TIMED OUT for ROUTER "(&00)" via ROUTE "(&01)"
Meaning
No more OSPF protocol HELLO messages received from ROUTER (&00)
via ROUTE (&01).
Now BCAM no longer uses the ROUTER (&00) via ROUTE "(&01)".
Response
Check the ROUTER (&00) via ROUTE "(&01)".
BCA0920
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0920 LINE "(&00)" READY FOR ACTIVATION
BCA0925
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA0925 TIMEOUT ON LINE "(&00)"
BCA0937
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0937 (&00) READY FOR ACTIVATION
Meaning
The processor (&00) is ready for activation.
BCA0950
Destination: CONSOLE Routing code: C Weight: 30
Warranty : NO
BCA0950 VLAN-LINE "(&00)" READY FOR ACTIVATION
BCA0955
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA0955 TIMEOUT ON VLAN-LINE "(&00)"
BCA0965
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA0965 TIMEOUT ON VLAN-DEVICE "(&00)"
BCA0980
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA0980 CMDCB-INDEX-TABLE IS FULL
Meaning
There are no free entries in CMDCB-INDEX-TABLE.The command control block
(CMDCB) could not be included in the table.
More than 4096 commands are not terminated.
BCA0990
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA0990 RSC I/O ERROR ON DEVICE "(&00)" OF VLAN-DEVICE "(&01)": RC=(&02),CC=(&03), SB=(&04)
Meaning
A RSC I/O error occurred on device (&00) of VLAN-DEVICE (&01).
This message is especially for the hardware service.
The error information given means:
RC RSC return code
CC RSC condition code
SB sense bytes
BCA0991
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA0991 RSC I/O ERROR ON DEVICE "(&00)" OF LINE "(&01)": RC=(&02),CC=(&03),SB=(&04)
Meaning
A RSC I/O error occurred on device (&00) of line (&01).
This message is especially for the hardware service.
The error information given means:
RC RSC return code
CC RSC condition code
SB sense bytes
BCA0995
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA0995 LENGTH ERROR ON DEVICE "(&00)": JUMBO FRAME RECEIVED
Meaning
A length error occurred on device (&00).
A jumbo frame has been received.
BCA0996
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA0996 I/O ERROR ON DEVICE "(&00)" OF VLAN-DEVICE "(&01)": CCW=(&02),LRC=(&03), EFB=(&04),EFB3=(&05),FLAG=(&06),CSB=(&07),USB/SDB=(&08),SB=(&09)
Meaning
An I/O error occurred on device (&00) of VLAN-DEVICE (&01).
This message is especially for the hardware service.
The error information given means:
CCW current CCW
LRC logical return code
EFB executive flag byte
EFB3 executive flag byte 3
FLAG flag byte
CSB channel status byte
USB/SDB unit status byte/standard device byte
SB sense bytes
BCA0997
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA0997 LENGTH ERROR ON LINE "(&00)": JUMBO FRAME RECEIVED
Meaning
A length error occurred on line (&00).
A jumbo frame has been received.
BCA0999
Destination: CONSOLE Routing code: C Weight: 99
Warranty : NO
BCA0999 I/O ERROR ON DEVICE "(&00)" OF LINE "(&01)": CCW=(&02),LRC=(&03),EFB=(&04), EFB3=(&05),FLAG=(&06),CSB=(&07),USB/SDB=(&08),SB=(&09)
Meaning
An I/O error occurred on device (&00) of line (&01).
This message is especially for the hardware service.
The error information given means:
CCW current CCW
LRC logical return code
EFB executive flag byte
EFB3 executive flag byte 3
FLAG flag byte
CSB channel status byte
USB/SDB unit status byte/standard device byte
SB sense bytes